The Effect of Silica and Prepolymer Nanoparticles on the Mechanical Properties of Denture Base Acrylic Resin

2016 ◽  
Vol 27 (8) ◽  
pp. 763-770 ◽  
Author(s):  
Pinar Cevik ◽  
Arzu Zeynep Yildirim-Bicer
Keyword(s):  
Mechanical Properties ◽  
Acrylic Resin ◽  
Denture Base

scholarly journals Novel acrylic resin denture base with enhanced mechanical properties by the incorporation of PMMA-modified hydroxyapatite

2013 ◽  
Vol 23 (1) ◽  
pp. 89-93 ◽  
Author(s):  
Yingying Pan ◽  
Fengwei Liu ◽  
Dan Xu ◽  
Xiaoze Jiang ◽  
Hao Yu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Acrylic Resin ◽  
Denture Base

scholarly journals TESTING OF THE FRACTURE RESISTANCE OF THE HEAT-CURING DENTURE BASE ACRYLIC RESIN

2018 ◽  
Vol 9 (2) ◽  
Author(s):  
Aleksandra Maletin ◽  
Jovana Bastajić ◽  
Ivan Ristić ◽  
Branislava Petronijević Šarčev ◽  
Isidora Nešković ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Fracture Resistance ◽  
Acrylic Resin ◽  
Denture Base ◽  
Universal Testing ◽  
Heat Curing ◽  
Significant Difference ◽  
Student’S T ◽  
Student’S T Test

For many years, poly-methyl methacrylate has been used as a material of choice for making the denture base, thanks to its good and desirable performances, such as: simplicity in work, possibility of reparation, aesthetics and affordable price. Considering to its insufficient hardness and fracture resistance, there is a tendency to improve the mechanical properties of the material, by changing its basic composition. The aim of the research was to determine the fracture resistance of the heat-curing denture base acrylic resin materials. Materials and methods: For the research ,20 samples of the 2 heat-curing acrylics had been prepared, standard ones and reinforced acrylic resin material. After the storage in the saline for 15 days, measurements of the fracture resistance were performed by using the universal testing device. The data were statistically processed using the Student’s t-test for independent samples. Results: By measuring the flexural strength and deflection at breakage, it has been proven that there was, statistically, a significant difference of the flexural strength between reinforced (179.91-248.72MPa) and standard heat-curing acrylics (183.25- 200.74MPa). The deflection at breakage showed approximately the same values for both materials (1,0-1,4mm; 1.0-1.5mm). Conclusion: By enhancing the polymer, the mechanical properties of the denture base acrylic resin materials will be improved, primarily, higher fracture resistance, that means that these technologies need to be improved.

scholarly journals Polytetrafluorethylene added to acrylic resins: mechanical properties

2010 ◽  
Vol 21 (1) ◽  
pp. 55-59 ◽  
Author(s):  
Fabiana Gouveia Straioto ◽  
Antonio Pedro Ricomini Filho ◽  
Alfredo Júlio Fernandes Neto ◽  
Altair Antoninha Del Bel Cury
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Flexural Modulus ◽  
Peak Load ◽  
Surface Hardness ◽  
Acrylic Resin ◽  
Denture Base ◽  
Standard Data ◽  
Acrylic Resins

The addition of different polymers, such as polytetrafluorethylene (PTFE), to denture base resins could be an option to modify acrylic resin mechanical properties. This study evaluated the surface hardness, impact and flexural strength, flexural modulus and peak load of 2 acrylic resins, one subjected to a long and another subjected to a short polymerization cycle, which were prepared with or without the addition of 2% PTFE. Four groups were formed according to the polymerization cycle and addition or not of PTFE. Forty specimens were prepared for each test (10 per group) with the following dimensions: hardness (30 mm diameter x 5 mm thick), impact strength (50 x 6 x 4 mm) and flexural strength (64 x 10 x 3.3 mm) test. The results of the flexural strength test allowed calculating flexural modulus and peak of load values. All tests were performed in accordance with the ISO 1567:1999 standard. Data were analyzed statistically by ANOVA and Tukey's test with the level of significance set at 5%. No statistically significant differences (p>0.05) were found for surface hardness. Flexural strength, impact strength and peak load were significantly higher (p<0.05) for resins without added PTFE. The flexural modulus of the acrylic resin with incorporated 2% PTFE polymerized by long cycle was significantly higher (p<0.05) than that of the other resins. Within the limits of this study, it may be concluded that the addition of PTFE did not improve the mechanical properties of the evaluated acrylic resins.

scholarly journals EFFECT OF E-GLASS FIBER ADDITION ON MECHANICAL PROPERTIES OF HEAT-POLYMERIZED ACRYLIC RESIN DENTURE BASE

2019 ◽  
Vol 8 (12) ◽  
pp. 872-878
Author(s):  
Sri Yuliharsini ◽  
Ismet Danial Nasution ◽  
Harry Agusnar ◽  
Putri Welda Utami Ritonga
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Acrylic Resin ◽  
Denture Base ◽  
Fiber Addition

scholarly journals 3D-Printed vs. Heat-Polymerizing and Autopolymerizing Denture Base Acrylic Resins

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5781
Author(s):  
Leila Perea-Lowery ◽  
Mona Gibreel ◽  
Pekka K. Vallittu ◽  
Lippo V. Lassila
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Water Solubility ◽  
Base Material ◽  
Acrylic Resin ◽  
Denture Base ◽  
3D Printed ◽  
Work Of Fracture

The aim of this work was to investigate the effect of two post-curing methods on the mechanical properties of a 3D-printed denture base material. Additionally, to compare the mechanical properties of that 3D-printed material with those of conventional autopolymerizing and a heat-cured denture base material. A resin for 3D-printing denture base (Imprimo®), a heat-polymerizing acrylic resin (Paladon® 65), and an autopolymerizing acrylic resin (Palapress®) were investigated. Flexural strength, elastic modulus, fracture toughness, work of fracture, water sorption, and water solubility were evaluated. The 3D-printed test specimens were post-cured using two different units (Imprimo Cure® and Form Cure®). The tests were carried out after both dry and 30 days water storage. Data were collected and statistically analyzed. Resin type had a significant effect on the flexural strength, elastic modulus, fracture toughness, and work of fracture (p < 0.001). The flexural strength and elastic modulus for the heat-cured polymer were significantly the highest among all investigated groups regardless of the storage condition (p < 0.001). The fracture toughness and work of fracture of the 3D-printed material were significantly the lowest (p < 0.001). The heat-cured polymer had the lowest significant water solubility (p < 0.001). The post-curing method had an impact on the flexural strength of the investigated 3D-printed denture base material. The flexural strength, elastic modulus, fracture toughness, work of fracture of the 3D-printed material were inferior to those of the heat-cured one. Increased post-curing temperature may enhance the flexural properties of resin monomers used for 3D-printing dental appliances.

Sign in / Sign up

Export Citation Format

Share Document