scholarly journals Effects of dentin and enamel porcelain layer thickness on the color of various ceramic restorations

2021 ◽  
Author(s):  
Binting Xu
Keyword(s):  
Layer Thickness ◽  
Ceramic Restorations

The influence of porcelain layer thickness on the final shade of ceramic restorations

2003 ◽  
Vol 90 (6) ◽  
pp. 563-570 ◽  
Author(s):  
Alma Dozić ◽  
Cornelis Johannes Kleverlaan ◽  
Marcel Meegdes ◽  
Jef van der Zel ◽  
Albert Joseph Feilzer
Keyword(s):  
Layer Thickness ◽  
Ceramic Restorations

Structure and Orientation of As Precipitates in LT-MBE Grown GaAs

1991 ◽  
Vol 49 ◽  
pp. 900-901 ◽  
Author(s):  
Alain Claverie ◽  
Zuzanna Liliental-Weber
Keyword(s):  
Transport Properties ◽  
Layer Thickness ◽  
Growth Temperature ◽  
Low Temperatures ◽  
Lattice Parameter ◽  
Crystalline Quality ◽  
Insulating Properties ◽  
Lt Gaas

GaAs layers grown by MBE at low temperatures (in the 200°C range, LT-GaAs) have been reported to have very interesting electronic and transport properties. Previous studies have shown that, before annealing, the crystalline quality of the layers is related to the growth temperature. Lowering the temperature or increasing the layer thickness generally results in some columnar polycrystalline growth. For the best “temperature-thickness” combinations, the layers may be very As rich (up to 1.25%) resulting in an up to 0.15% increase of the lattice parameter, consistent with the excess As. Only after annealing are the technologically important semi-insulating properties of these layers observed. When annealed in As atmosphere at about 600°C a decrease of the lattice parameter to the substrate value is observed. TEM studies show formation of precipitates which are supposed to be As related since the average As concentration remains almost unchanged upon annealing.

The stabilization of B.C.C. Cu in Cu/Nb nanolayered composites

1996 ◽  
Vol 54 ◽  
pp. 228-229
Author(s):  
H. Kung ◽  
A.J. Griffin ◽  
Y.C. Lu ◽  
K.E. Sickafus ◽  
T.E. Mitchell ◽  
...  
Keyword(s):  
Electrical Resistivity ◽  
Layer Thickness ◽  
Volume Fraction ◽  
Ion Beam ◽  
High Strength ◽  
Cross Sectional ◽  
Metastable Structure ◽  
High Resolution Tem ◽  
Potential Improvement ◽  
Two Phases

Materials with compositionally modulated structures have gained much attention recently due to potential improvement in electrical, magnetic and mechanical properties. Specifically, Cu-Nb laminate systems have been extensively studied mainly due to the combination of high strength, and superior thermal and electrical conductivity that can be obtained and optimized for the different applications. The effect of layer thickness on the hardness, residual stress and electrical resistivity has been investigated. In general, increases in hardness and electrical resistivity have been observed with decreasing layer thickness. In addition, reduction in structural scale has caused the formation of a metastable structure which exhibits uniquely different properties. In this study, we report the formation of b.c.c. Cu in highly textured Cu/Nb nanolayers. A series of Cu/Nb nanolayered films, with alternating Cu and Nb layers, were prepared by dc magnetron sputtering onto Si {100} wafers. The nominal total thickness of each layered film was 1 μm. The layer thickness was varied between 1 nm and 500 nm with the volume fraction of the two phases kept constant at 50%. The deposition rates and film densities were determined through a combination of profilometry and ion beam analysis techniques. Cross-sectional transmission electron microscopy (XTEM) was used to examine the structure, phase and grain size distribution of the as-sputtered films. A JEOL 3000F high resolution TEM was used to characterize the microstructure.

On the Effect of 2-Layer Thickness by High-Specific Gravity Armor Blocks on Wave Reflection

1999 ◽  
Author(s):  
Masahiro Ito ◽  
Yuitch Iwagaki ◽  
Hiroshi Murakami ◽  
Kenji Nemoto ◽  
Masato Yamamoto ◽  
...  
Keyword(s):  
Specific Gravity ◽  
Layer Thickness ◽  
Wave Reflection ◽  
High Specific Gravity

Exciton dynamics in thick GaN MOVPE epilayers deposited on sapphire.

1997 ◽  
Vol 2 ◽  
Author(s):  
J. Allègre ◽  
P. Lefebvre ◽  
J. Camassel ◽  
B. Beaumont ◽  
Pierre Gibart
Keyword(s):  
Layer Thickness ◽  
Buffer Layers ◽  
Rate Equations ◽  
Time Resolved ◽  
Versus Layer ◽  
Level Model ◽  
Shallow Impurities ◽  
Aln Buffer ◽  
Time Resolved Photoluminescence

Time-resolved photoluminescence spectra have been recorded on three GaN epitaxial layers of thickness 2.5 μm, 7 μm and 16 μm, at various temperatures ranging from 8K to 300K. The layers were deposited by MOVPE on (0001) sapphire substrates with standard AlN buffer layers. To achieve good homogeneities, the growth was in-situ monitored by laser reflectometry. All GaN layers showed sharp excitonic peaks in cw PL and three excitonic contributions were seen by reflectivity. The recombination dynamics of excitons depends strongly upon the layer thickness. For the thinnest layer, exponential decays with τ ~ 35 ps have been measured for both XA and XB free excitons. For the thickest layer, the decay becomes biexponential with τ1 ~ 80 ps and τ2 ~ 250 ps. These values are preserved up to room temperature. By solving coupled rate equations in a four-level model, this evolution is interpreted in terms of the reduction of density of both shallow impurities and deep traps, versus layer thickness, roughly following a L−1 law.

Sign in / Sign up

Export Citation Format

Share Document