Pressureless sintering of transparent AlON ceramic with assimilable γ‐Al 2 O 3 as sintering promoting additives

2022 ◽  
Author(s):  
Zhao Feng ◽  
Xu Huang ◽  
Dan Chen ◽  
Zhijun Liao ◽  
Jianqi Qi ◽  
...  
Keyword(s):  
Pressureless Sintering

scholarly journals Pressureless Sintering of YIG Ceramics from Coprecipitated Nanopowders

2021 ◽  
Vol 7 (5) ◽  
pp. 56
Author(s):  
Yimin Yang ◽  
Xiaoying Li ◽  
Ziyu Liu ◽  
Dianjun Hu ◽  
Xin Liu ◽  
...  
Keyword(s):  
High Temperature ◽  
Calcination Temperature ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Secondary Phase ◽  
Coprecipitation Method ◽  
Pressureless Sintering ◽  
Densification Behavior ◽  
Sintering Process

Nanoparticles prepared by the coprecipitation method were used as raw materials to fabricate Y3Fe5O12 (YIG) ceramics by air pressureless sintering. The synthesized YIG precursor was calcinated at 900–1100 °C for 4 h in air. The influences of the calcination temperature on the phase and morphology of the nanopowders were investigated in detail. The powders calcined at 1000–1100 °C retained the pure YIG phase. YIG ceramics were fabricated by sintering at 1200–1400 °C for 10 h, and its densification behavior was studied. YIG ceramics prepared by air sintering at 1250 °C from powders calcinated at 1000 °C have the highest in-line transmittance in the range of 1000-3000 nm. When the sintering temperature exceeds 1300 °C, the secondary phase appears in the YIG ceramics, which may be due to the loss of oxygen during the high-temperature sintering process, resulting in the conversion of Fe3+ into Fe2+.

scholarly journals Improvement of mechanical properties of HfB2-based composites by incorporating in situ SiC reinforcement through pressureless sintering

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
S. Ghadami ◽  
E. Taheri-Nassaj ◽  
H. R. Baharvandi ◽  
F. Ghadami
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Relative Density ◽  
Pressureless Sintering ◽  
Sintering Process ◽  
Vacuum Atmosphere ◽  
Sic Reinforcement ◽  
Microstructural Studies ◽  
Composite Samples

AbstractHfB2, Si, and activated carbon powders were selected to fabricate 0–30 vol% SiC reinforced HfB2-based composite. Pressureless sintering process was performed at 2050 °C for 4 h under a vacuum atmosphere. Microstructural studies revealed that in situ SiC reinforcement was formed and distributed in the composite according to the following reaction: Si + C = SiC. A maximum relative density of 98% was measured for the 20 vol% SiC containing HfB2 composite. Mechanical investigations showed that the hardness and the fracture toughness of these composites were increased and reached up to 21.2 GPa for HfB2-30 vol% SiC and 4.9 MPa.m1/2 for HfB2-20 vol% SiC, respectively. Results showed that alpha-SiC reinforcements were created jagged, irregular, and elongated in shape which were in situ formed between HfB2 grains and filled the porosities. Formation of alpha-SiC contributed to improving the relative density and mechanical properties of the composite samples. By increasing SiC content, an enhanced trend of thermal conductivity was observed as well as a reduced trend for electrical conductivity.

scholarly journals Fabrication of Hydroxyapatite/Tantalum Composites by Pressureless Sintering in Different Atmosphere

ACS Omega ◽  
2021 ◽  
Author(s):  
Cuiling Cai ◽  
Xinyu Wang ◽  
Binbin Li ◽  
Kuo Dong ◽  
Ying Shen ◽  
...  
Keyword(s):  
Pressureless Sintering

Preparation of intragranular-oxide-strengthened ultrafine-grained tungsten via low-temperature pressureless sintering

2020 ◽  
Vol 774 ◽  
pp. 138878 ◽  
Author(s):  
Mingli Qin ◽  
Junjun Yang ◽  
Zheng Chen ◽  
Pengqi Chen ◽  
Shangjie Zhao ◽  
...  
Keyword(s):  
Low Temperature ◽  
Pressureless Sintering ◽  
Ultrafine Grained

Effect of TiO2 and MgO on Microstructure of α-Alumina Ceramics and its Sintering Behavior

2015 ◽  
Vol 1112 ◽  
pp. 519-523 ◽  
Author(s):  
Jarot Raharjo ◽  
Sri Rahayu ◽  
Tika Mustika ◽  
Masmui ◽  
Dwi Budiyanto
Keyword(s):  
Mechanical Properties ◽  
Sintering Temperature ◽  
Physical And Mechanical Properties ◽  
Basic Material ◽  
Sintering Behavior ◽  
Pressureless Sintering ◽  
Alumina Ceramics ◽  
Density Measurements ◽  
Technical Alumina ◽  
Platelet Structure

Observation on the effect of adding titanium oxide (TiO2) and magnesium oxide (MgO) on the sintering of α-alumina (Al2O3) has been performed. In this study, technical alumina used as basic material in which the sample is formed by the pressureless sintering/cold press and sintered at 1500°C which is lower than alumina sintering temperature at 1700°C. Elemental analysis, observation of microstructure, hardness, fracture toughness and density measurements were carried out to determine the physical and mechanical properties of alumina. The results indicate a change in the microstructure where the content of the platelet structure are much more than the equilateral structure. At sintering temperature of 1500°C, neck growth occurs at ceramics grain, supported by the results of the density test which indicate perfect compaction has occurred in this process.

Preparation of Porous HA Bioceramics by Gelcasting and Pressureless Sintering

2011 ◽  
Vol 335-336 ◽  
pp. 1454-1458
Author(s):  
Jing Xian Zhang ◽  
Bi Qin Chen ◽  
Dong Liang Jiang ◽  
Qing Ling Lin ◽  
Zhong Ming Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Pore Size ◽  
Pressureless Sintering ◽  
High Compressive Strength ◽  
Microstructure And Properties ◽  
Pmma Beads ◽  
Average Compressive Strength

In the present work, porous HA scaffolds with well controlled pore size, porosity and high compressive strength were prepared by aqueous gelcasting. PMMA beads with different size were used as the pore forming agent. The compositions, microstructure and properties of porous HA bioceramics were analyzed by XRD, SEM, Hg porosimetry etc. The mechanical properties were also tested. For scaffolds with the porosity as 70%, the average compressive strength was 11.9±1.7 MPa. Results showed that glecasting process can be used for the preparation of porous HA biomaterials with well controlled pore size and improved mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document