Sintering behavior of a nanostructured thermal barrier coating deposited using electro‐sprayed particles

2020 ◽  
Vol 103 (12) ◽  
pp. 7267-7282
Author(s):  
Chen Xing ◽  
Meiyu Yi ◽  
Xiao Shan ◽  
Xin Wang ◽  
Xiaofeng Zhao ◽  
...  
Keyword(s):  
Thermal Barrier Coating ◽  
Sintering Behavior ◽  
Thermal Barrier ◽  
Barrier Coating ◽  
Nanostructured Thermal Barrier Coating

Sintering Behavior of Plasma-Sprayed Sm2Zr2O7 Coating

2010 ◽  
Author(s):  
Jianhua Yu ◽  
Huayu Zhao ◽  
Shunyan Tao ◽  
Xiaming Zhou ◽  
Chuanxian Ding
Keyword(s):  
Thermal Conductivity ◽  
Thermal Expansion ◽  
High Temperature ◽  
Thermal Expansion Coefficient ◽  
Thermal Barrier Coating ◽  
Expansion Coefficient ◽  
Sintering Behavior ◽  
Thermal Barrier ◽  
Barrier Coating ◽  
Plasma Sprayed

Plasma-sprayed thermal barrier coating (TBC) systems are widely used in gas turbine blades to increase turbine entry temperature (TET) and better efficiency. Yttria stabilized zirconia (YSZ) has been the conventional thermal barrier coating material because of its low thermal conductivity, relative high thermal expansion coefficient and good corrosion resistance. However the YSZ coatings can hardly fulfill the harsh requirements in future for higher reliability and the lower thermal conductivity at higher temperatures. Among the interesting TBC candidates, materials with pyrochlore structure show promising thermo-physical properties for use at temperatures exceeding 1200 °C. Sm2Zr2O7 bulk material does not only have high temperature stability, sintering resistance but also lower thermal conductivity and higher thermal expansion coefficient. The sintering characteristics of ceramic thermal barrier coatings under high temperature conditions are complex phenomena. In this paper, samarium zirconate (Sm2Zr2O7, SZ) powder and coatings were prepared by solid state reaction and atmosphere plasma spraying process, respectively. The microstructure development of coatings derived from sintering after heat-treated at 1200–1500 °C for 50 h have been investigated. The microstructure was examined by scanning electron microscopy (SEM) and the grain growth was analyzed in this paper as well.

scholarly journals Sintering Behavior of Zirconia Thermal Barrier Coating under Gradient Temperature.

1999 ◽  
Vol 48 (7) ◽  
pp. 740-745 ◽  
Author(s):  
Yoshiyasu ITOH ◽  
Tsuneji KAMEDA ◽  
Takanari OKAMURA ◽  
Kohsoku NAGATA
Keyword(s):  
Thermal Barrier Coating ◽  
Sintering Behavior ◽  
Thermal Barrier ◽  
Barrier Coating

Heat treatment of nanostructured thermal barrier coating

2007 ◽  
Vol 33 (6) ◽  
pp. 1075-1081 ◽  
Author(s):  
Na Wang ◽  
Chungen Zhou ◽  
Shengkai Gong ◽  
Huibin Xu
Keyword(s):  
Heat Treatment ◽  
Thermal Barrier Coating ◽  
Thermal Barrier ◽  
Barrier Coating ◽  
Nanostructured Thermal Barrier Coating

HOT CORROSION OF CERIA-YTTRIA STABILIZED ZIRCONIA PLASMA SPRAYED THERMAL BARRIER COATING BY EUTECTIC VANDIUM PENTAOXIDE-SODIUM SULFATE

2018 ◽  
Vol 18 (1) ◽  
pp. 182-192 ◽  
Author(s):  
Mohammed J Kadhim ◽  
Mohammed H Hafiz ◽  
Maryam A Ali Bash
Keyword(s):  
Thermal Barrier Coating ◽  
Hot Corrosion ◽  
Monoclinic Phase ◽  
Volume Fraction ◽  
High Volume ◽  
Thermal Barrier ◽  
Air Plasma ◽  
Plan View ◽  
Barrier Coating ◽  
Plasma Sprayed

The high temperature corrosion behavior of thermal barrier coating (TBC) systemconsisting of IN-738 LC superalloy substrate, air plasma sprayed Ni24.5Cr6Al0.4Y (wt%)bond coat and air plasma sprayed ZrO2-20 wt% ceria-3.6 wt% yttria (CYSZ) ceramic coatwere characterized. The upper surfaces of CYSZ covered with 30 mg/cm2 , mixed 45 wt%Na2SO4-55 wt% V2O5 salt were exposed at different temperatures from 800 to 1000 oC andinteraction times from 1 up to 8 h. The upper surface plan view of the coatings wereidentified for topography, roughness, chemical composition, phases and reaction productsusing scanning electron microscopy, energy dispersive spectroscopy, talysurf, and X-raydiffraction. XRD analyses of the plasma sprayed coatings after hot corrosion confirmed thephase transformation of nontransformable tetragonal (t') into monoclinic phase, presence ofYVO4 and CeVO4 products. Analysis of the hot corrosion CYSZ coating confirmed theformation of high volume fraction of YVO4, with low volume fractions of CeOV4 and CeO2.The formation of these compounds were combined with formation of monoclinic phase (m)from transformation of nontransformable tetragonal phase (t').

Evaluation of Spatial Resolution of Nondestructive Testing of Thermal Barrier Coating by Terahertz Imaging

2012 ◽  
Vol 132 (10) ◽  
pp. 864-870
Author(s):  
Tetsuo Fukuchi ◽  
Norikazu Fuse ◽  
Mitsutoshi Okada ◽  
Tomoharu Fujii ◽  
Maya Mizuno ◽  
...  
Keyword(s):  
Nondestructive Testing ◽  
Thermal Barrier Coating ◽  
Spatial Resolution ◽  
Terahertz Imaging ◽  
Thermal Barrier ◽  
Barrier Coating
Sign in / Sign up

Export Citation Format

Share Document