In vitro precision of fit of computer-aided designed and computer-aided manufactured titanium screw-retained fixed dental prostheses before and after ceramic veneering

2013 ◽  
Vol 26 (1) ◽  
pp. 44-49 ◽  
Author(s):  
Joannis Katsoulis ◽  
Regina Mericske-Stern ◽  
Norbert Enkling ◽  
Konstantinos Katsoulis ◽  
Markus B. Blatz
Keyword(s):  
Titanium Screw ◽  
Dental Prostheses ◽  
Computer Aided ◽  
Before And After ◽  
Fixed Dental Prostheses

scholarly journals Does Printing Orientation Matter? In-Vitro Fracture Strength of Temporary Fixed Dental Prostheses after a 1-Year Simulation in the Artificial Mouth

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 259
Author(s):  
Julian Nold ◽  
Christian Wesemann ◽  
Laura Rieg ◽  
Lara Binder ◽  
Siegbert Witkowski ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Fracture Strength ◽  
Computer Aided Design ◽  
In Vitro Study ◽  
Bending Test ◽  
Dental Prostheses ◽  
Computer Aided ◽  
Subtractive Manufacturing ◽  
Fixed Dental Prostheses

Computer-aided design and computer-aided manufacturing (CAD–CAM) enable subtractive or additive fabrication of temporary fixed dental prostheses (FDPs). The present in-vitro study aimed to compare the fracture resistance of both milled and additive manufactured three-unit FDPs and bar-shaped, ISO-conform specimens. Polymethylmethacrylate was used for subtractive manufacturing and a light-curing resin for additive manufacturing. Three (bars) and four (FDPs) different printing orientations were evaluated. All bars (n = 32) were subjected to a three-point bending test after 24 h of water storage. Half of the 80 FDPs were dynamically loaded (250,000 cycles, 98 N) with simultaneous hydrothermal cycling. Non-aged (n = 40) and surviving FDPs (n = 11) were subjected to static loading until fracture. Regarding the bar-shaped specimens, the milled group showed the highest flexural strength (114 ± 10 MPa, p = 0.001), followed by the vertically printed group (97 ± 10 MPa, p < 0.007). Subtractive manufactured FDPs revealed the highest fracture strength (1060 ± 89 N) with all specimens surviving dynamic loading. During artificial aging, 29 of 32 printed specimens failed. The present findings indicate that both printing orientation and aging affect the strength of additive manufactured specimens. The used resin and settings cannot be recommended for additive manufacturing of long-term temporary three-unit FDPs.

scholarly journals Cytomorphometric Analysis of Inflammation Dynamics in the Periodontium Following the Use of Fixed Dental Prostheses

Molecules ◽  
2020 ◽  
Vol 25 (20) ◽  
pp. 4650
Author(s):  
Artak Heboyan ◽  
Azeem Ul Yaqin Syed ◽  
Dinesh Rokaya ◽  
Paul R. Cooper ◽  
Mikael Manrikyan ◽  
...  
Keyword(s):  
Epithelial Cells ◽  
Periodontal Diseases ◽  
Cell Counts ◽  
Dental Prostheses ◽  
Computer Aided ◽  
Metal Ceramic ◽  
Before And After ◽  
Cad Cam ◽  
Fixed Dental Prostheses ◽  
Cobalt Chrome

Cytomorphometry is used in the sampling of biological materials and diagnostic procedures. The use of cytological studies in periodontal diseases is not well described in the literature. Our study aimed to quantitatively assess the inflammation dynamics using cytomorphometric analysis of the periodontium before and after the use of fixed dental prostheses. Following ethics approval, a total of 105 subjects were divided in 3 groups as gingivitis (n = 23), periodontitis (n = 58), and healthy periodontium (control) (n = 24). The fixed dental prostheses (crowns and fixed partial dentures) were fabricated from cobalt-chrome metal-ceramic prostheses using the conventional method (C/M-CoCr), cobalt-chrome metal-ceramic prostheses by the computer-aided design and computer-aided manufacturing (CAD/CAM) technique (C/C-CoCr), and zirconia-based ceramic prostheses by the CAD/CAM technique (C/C-Zr) among subjects with gingivitis and periodontitis. The gingival crevicular fluid (GCF) was obtained from subjects before and after the use of the prostheses. The total count of epithelial cells and the connective tissue cells or polymorphonuclear neutrophils (PMNs) in GCF were studied using cytomorphometric analysis. The Statistical Package Tor the Social Sciences (SPSS), Version 20 (IBM Company, Chicago, IL, USA) was used to analyze the results and the significance level was set at p = 0.05. The data for before and after the use of the prostheses were compared using independent t-Tests. Similarly, the results after the use of prostheses in gingivitis, periodontitis, and control in each type of prostheses were compared using One-way ANOVA with post hoc using Scheffe. The total epithelial cells and the PMNs were determined along with the epithelium/leukocyte index. Regardless of the prostheses type used, no significant change in the parameters was identified among patients with a healthy periodontium, before and after prosthetic treatment. In all study groups, a statistically increase (p value < 0.05) was observed in the oral epithelial cell counts and a statistically decrease (p < 0.05) in the PMNs count following the use of the fixed prostheses. Data on cytomorphometric analysis could enable the selection of the most appropriate prostheses for use in patients with periodontal pathologies. When choosing prostheses, changes in the composition of GCF could be considered as a useful criterion for their use.

scholarly journals Influence of Sequential CAD/CAM Milling on the Fitting Accuracy of Titanium Three-Unit Fixed Dental Prostheses

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1401
Author(s):  
Doo-Bin Song ◽  
Man-So Han ◽  
Si-Chul Kim ◽  
Junyong Ahn ◽  
Yong-Woon Im ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Computer Aided Design ◽  
Dental Prostheses ◽  
Computer Aided ◽  
Cad Cam ◽  
Fixed Dental Prostheses ◽  
Gap Data ◽  
Aided Design ◽  
Fitting Accuracy

This study investigated the fitting accuracy of titanium alloy fixed dental prostheses (FDP) after sequential CAD/CAM (Computer Aided Design/Computer Aided Manufacturing) fabrication. A three-unit FDP model connecting mandibular second premolars and molars was prepared and scanned to fabricate titanium FDPs by CAD/CAM milling. A total of six FDPs were sequentially milled in one titanium alloy disk using a new set of burs every time (n = 4). The fitting accuracy of FDPs was mesiodistally evaluated by a silicone replica technique and the measurement was triplicated at four different locations: MO (marginal opening), MG (marginal gap), AG (axial gap), and OG (occlusal gap). Data were statistically analyzed using ANOVA and Tukey’s HSD test. The fitting accuracy of PMMA (polymethyl methacrylate) FDPs milled using the worn or new bur were evaluated by the same procedure (n = 6). The mean dimensions of titanium FDP for all measuring positions, except for AG, were significantly increased from the third milling. However, no difference was noted between the first FDP and the second FDP milled with the same set of burs. Severe edge chippings were observed in all milling burs. Detrimental effects of the worn burs on the fitting accuracy were demonstrated in the CAD/CAM-milled PMMA FDP. The results recommend proper changing frequency of cutting burs to achieve the quality of fit and predictable outcomes for dental CAD/CAM prostheses.

scholarly journals Strategic Use of CAD-CAM Interim Restoration for the Recovery of the Vertical Dimension of Occlusion in the Posterior Partially Edentulous Jaw

2020 ◽  
Vol 10 (21) ◽  
pp. 7735
Author(s):  
Hai Yen Mai ◽  
Jae-Min Seo ◽  
Jae-Kwang Jung ◽  
Du-Hyeong Lee
Keyword(s):  
Case Report ◽  
Computer Aided Design ◽  
Vertical Dimension ◽  
Posterior Region ◽  
Occlusal Contact ◽  
Dental Prostheses ◽  
Computer Aided ◽  
Cad Cam ◽  
Fixed Dental Prostheses ◽  
Aided Design

Occlusal contact loss occasionally occurs following the placement of implant-supported fixed dental prostheses in the posterior region. This complication is caused by the change in the vertical dimension of occlusion after the recovery of mastication. The change is probably related to the prosthesis sinking phenomenon and previous mandibular dislocation. The use of interim prostheses could help re-establish the vertical dimension of occlusion. The definitive prostheses can then be accurately fabricated using digital techniques in the newly established vertical dimension. In this case report, we introduce a protocol incorporating a computer-aided design and computer-aided manufacturing (CAD-CAM) interim prosthesis and digital techniques to minimize the occurrence of unexpected initial occlusal changes in the prosthetic treatment of implant-supported prostheses in the posterior region.

scholarly journals Fracture Resistance of CAD/CAM Versus Traditional Interim Fixed Dental Prostheses

2018 ◽  
Vol 55 (3) ◽  
pp. 361-363
Author(s):  
Daniel Alexandru Pop ◽  
R. Malaescu ◽  
Liviu Marsavina ◽  
Tiberiu Hosszu ◽  
Raul Rotar ◽  
...  
Keyword(s):  
Testing Machine ◽  
In Vitro Study ◽  
Maximum Load ◽  
Fracture Load ◽  
Digital Design ◽  
Computer Assisted ◽  
Dental Prostheses ◽  
Cad Cam ◽  
Fixed Dental Prostheses

The aim of this in vitro study is to compare the load-to-fracture performance of polymethyl methacrylates (PMMA) provisional restorations manufactured with a traditional laboratory technique in comparison to a computer-assisted design and computer-assisted manufacturing (CAD-CAM) technique. Five interim three-unit fixed dental prostheses were fabricated with the conventional indirect technique, on a standard typodont. The same model was scanned with an intraoral scanner and the digital design of identical fixed dental prostheses was made. Then other five interim three-unit fixed dental prostheses were milled from PMMA CAD/CAM blocks with an in office milling machine. All specimens were tested for flexural strength in a universal testing machine, and the maximum load to fracture was measured. For the conventional provisional restorations, the load to fracture was 121.16 � 24.6, in comparison to CAD/CAM interim restorations, for which the load to fracture was 728.88 � 228.7. Within the limitations of this study, one can conclude that CAD/CAM provisional restorations present a higher fracture load than the conventional manufactured interim restorations.

scholarly journals The Effect of Resin Bonding on Long-Term Success of High-Strength Ceramics

2017 ◽  
Vol 97 (2) ◽  
pp. 132-139 ◽  
Author(s):  
M.B. Blatz ◽  
M. Vonderheide ◽  
J. Conejo
Keyword(s):  
Clinical Success ◽  
High Strength ◽  
Composite Resins ◽  
Partial Coverage ◽  
Dental Prostheses ◽  
Computer Aided ◽  
Fixed Dental Prostheses ◽  
Ceramic Restorations ◽  
Resin Bonding

Digital manufacturing, all-ceramics, and adhesive dentistry are currently the trendiest topics in clinical restorative dentistry. Tooth- and implant-supported fixed restorations from computer-aided design (CAD)/computer-aided manufacturing (CAM)–fabricated high-strength ceramics—namely, alumina and zirconia—are widely accepted as reliable alternatives to traditional metal-ceramic restorations. Most recent developments have focused on high-translucent monolithic full-contour zirconia restorations, which have become extremely popular in a short period of time, due to physical strength, CAD/CAM fabrication, and low cost. However, questions about proper resin bonding protocols have emerged, as they are critical for clinical success of brittle ceramics and treatment options that rely on adhesive bonds, specifically resin-bonded fixed dental prostheses or partial-coverage restorations such as inlays/onlays and veneers. Resin bonding has long been the gold standard for retention and reinforcement of low- to medium-strength silica-based ceramics but requires multiple pretreatment steps of the bonding surfaces, increasing complexity, and technique sensitivity compared to conventional cementation. Here, we critically review and discuss the evidence on resin bonding related to long-term clinical outcomes of tooth- and implant-supported high-strength ceramic restorations. Based on a targeted literature search, clinical long-term studies indicate that porcelain-veneered alumina or zirconia full-coverage crowns and fixed dental prostheses have high long-term survival rates when inserted with conventional cements. However, most of the selected studies recommend resin bonding and suggest even greater success with composite resins or self-adhesive resin cements, especially for implant-supported restorations. High-strength ceramic resin-bonded fixed dental prostheses have high long-term clinical success rates, especially when designed as a cantilever with only 1 retainer. Proper pretreatment of the bonding surfaces and application of primers or composite resins that contain special adhesive monomers are necessary. To date, there are no clinical long-term data on resin bonding of partial-coverage high-strength ceramic or monolithic zirconia restorations.

In vitro comparison of trueness of 10 intraoral scanners for implant-supported complete-arch fixed dental prostheses

2020 ◽  
Vol 124 (6) ◽  
pp. 755-760 ◽  
Author(s):  
Caglar Bilmenoglu ◽  
Altug Cilingir ◽  
Onur Geckili ◽  
Hakan Bilhan ◽  
Tayfun Bilgin
Keyword(s):  
Dental Prostheses ◽  
Fixed Dental Prostheses ◽  
In Vitro Comparison
Sign in / Sign up

Export Citation Format

Share Document