A new wave energy converter using flap-type blade and its power generation test

2017 ◽  
Author(s):  
Hangil Joe ◽  
Hyunwoo Roh ◽  
Son-Cheol Yu
Keyword(s):  
Power Generation ◽  
Wave Energy ◽  
Wave Energy Converter ◽  
New Wave ◽  
Energy Converter ◽  
Generation Test

scholarly journals A Piezoelectric Wave-Energy Converter Equipped with a Geared-Linkage-Based Frequency Up-Conversion Mechanism

Sensors ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 204
Author(s):  
Shao-En Chen ◽  
Ray-Yeng Yang ◽  
Guang-Kai Wu ◽  
Chia-Che Wu
Keyword(s):  
Power Generation ◽  
Wave Energy ◽  
Wave Motion ◽  
Wave Energy Converter ◽  
Gear Train ◽  
Piezoelectric Composite ◽  
Maximum Height ◽  
Resistive Load ◽  
Linkage Mechanism ◽  
Energy Converter

In this paper, a piezoelectric wave-energy converter (PWEC), consisting of a buoy, a frequency up-conversion mechanism, and a piezoelectric power-generator component, is developed. The frequency up-conversion mechanism consists of a gear train and geared-linkage mechanism, which converted lower frequencies of wave motion into higher frequencies of mechanical motion. The slider had a six-period displacement compared to the wave motion and was used to excite the piezoelectric power-generation component. Therefore, the operating frequency of the piezoelectric power-generation component was six times the frequency of the wave motion. The developed, flexible piezoelectric composite films of the generator component were used to generate electrical voltage. The piezoelectric film was composed of a copper/nickel foil as the substrate, lead–zirconium–titanium (PZT) material as the piezoelectric layer, and silver material as an upper-electrode layer. The sol-gel process was used to fabricate the PZT layer. The developed PWEC was tested in the wave flume at the Tainan Hydraulics Laboratory, Taiwan (THL). The maximum height and the minimum period were set to 100 mm and 1 s, respectively. The maximum voltage of the measured value was 2.8 V. The root-mean-square (RMS) voltage was 824 mV, which was measured through connection to an external 495 kΩ resistive load. The average electric power was 1.37 μW.

Design and analysis of a new wave energy converter based on a point absorber and a hydraulic system harvesting energy from waves near the shore in calm seas

2020 ◽  
Vol 45 (1) ◽  
pp. 661-690
Author(s):  
Silvio Barbarelli ◽  
Mario Amelio ◽  
Teresa Castiglione ◽  
Gaetano Florio ◽  
Nino Michele Scornaienchi
Keyword(s):  
Wave Energy ◽  
Hydraulic System ◽  
Wave Energy Converter ◽  
New Wave ◽  
Energy Converter ◽  
Point Absorber

The new wave energy converter WaveCat: Concept and laboratory tests

2012 ◽  
Vol 29 (1) ◽  
pp. 58-70 ◽  
Author(s):  
H. Fernandez ◽  
G. Iglesias ◽  
R. Carballo ◽  
A. Castro ◽  
J.A. Fraguela ◽  
...  
Keyword(s):  
Wave Energy ◽  
Laboratory Tests ◽  
Wave Energy Converter ◽  
New Wave ◽  
Energy Converter

A Mathematical Model With Preliminary Experiments of a Gyroscopic Ocean Wave Energy Converter

2015 ◽  
Author(s):  
Hidenori Murakami ◽  
Oscar Rios ◽  
Ardavan Amini
Keyword(s):  
Mathematical Model ◽  
Power Generation ◽  
Wave Energy ◽  
Equations Of Motion ◽  
Energy Generation ◽  
Wave Energy Converter ◽  
Ocean Wave ◽  
Scale Model ◽  
Energy Converter ◽  
Ocean Wave Energy

Global attempts to increase generation of clean and reproducible natural energy have greatly contributed to the progress of solar, wind, biomass, and geothermal energy generation. To meet the goal set by the Renewable Portfolio Standards (RPS) in the United States, it is advisable for several of the coastal states to tap into the least explored resource: ocean-wave energy. There are many advantages to ocean-wave energy generation. First, the energy per unit area is 20 to 30 times larger compared with solar and five to ten times larger when compared to wind energy. Second, waves are more easily predicted than wind. Currently, there are several challenges with capturing ocean energy: With respect to the environment, noise pollution and effects on marine life need to be taken into consideration; with respect to design, ocean-wave power generators need to withstand large waves due to hurricanes and be designed to lessen visual pollution. There are various methods and devices used to capture ocean wave energy. Point absorbers, such as PowerBuoy, can harness vertical or heaving motion into electricity while attenuators like Pelamis use the induced movement of its joints from the incoming waves. Unfortunately, many have few parameters that can be varied to optimize power generation and or suffer from the various challenges mentioned above. The gyroscopic ocean wave energy converter harnesses the rocking or pitching motion induced by the ocean waves and converts it into rotary motion that is then fed to a generator. Furthermore, it is a fully enclosed floating device that has several parameters that can be varied to optimize power output. Previous work has demonstrated the viability of such a device, but the theoretical modeling of these converters is still in its infancy compared to that of other ocean wave energy converters. The objective of the research presented is to fully understand the mechanisms of power generation in the gyroscopic ocean wave energy converter. Using the moving frame method, a mathematical model of the device is developed. The nonlinear equations of motion are derived through the use of this novel method and then solved numerically. The results are then used to optimize the system and identify key parameters and their effect on the output power generated. Additionally, the resulting equations serve as a tool for identifying an appropriate control strategy for the system. Finally, a scale model of a gyroscopic ocean wave energy converter is developed to validate the equations of motion that have been derived.

Harnessing the kinetic and potential wave energy: Design and development of a new wave energy converter

2015 ◽  
pp. 367-374 ◽  
Author(s):  
P Rosa-Santos ◽  
F Taveira-Pinto ◽  
J Pinho-Ribeiro ◽  
L Teixeira ◽  
J Marinheiro
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
New Wave ◽  
Energy Converter ◽  
Design And Development ◽  
Potential Wave

scholarly journals Optimization of an Invention Based on a Force Multiplier Mechanism for Wave Power Generation

2014 ◽  
Vol 507 ◽  
pp. 480-485
Author(s):  
Javier Aparisi ◽  
Jose González ◽  
Bernabé Hernandis
Keyword(s):  
Power Generation ◽  
Wave Height ◽  
Wave Energy ◽  
Fossil Fuels ◽  
Clean Energy ◽  
Wave Energy Converter ◽  
Wave Power ◽  
Rectilinear Motion ◽  
Energy Converter ◽  
The Waves

The development and exploitation of new sources of clean energy that do not depend on traditional sources based on the use of fossil fuels, is the focus of this research, which starts with the optimization of an invention capable of transforming a reciprocating rectilinear motion into continuous circular motion in a very efficient way, to be used in the development of a Wave Energy Converter (WEC), capable of operating with low wave height and taking advantage of the oscillating movement of the waves both when rising, and when lowering, unlike other similar devices that harness it only in one way.

Sign in / Sign up

Export Citation Format

Share Document