Measurement and Research of the Characteristics of Noise Distribution in Three-Phase Four-Wire Low-Voltage Power Network Channels

2007 ◽  
Vol 22 (1) ◽  
pp. 122-128 ◽  
Author(s):  
Yang Xiaoxian ◽  
Zheng Tao ◽  
Zhang Baohui
Keyword(s):  
Low Voltage ◽  
Noise Distribution ◽  
Power Network ◽  
Three Phase

scholarly journals D-PMU and 5G-Network-Based Coordination Control Method for Three-Phase Imbalance Mitigation Units in the LVDN

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2754
Author(s):  
Mengmeng Xiao ◽  
Shaorong Wang ◽  
Zia Ullah
Keyword(s):  
Mobile Networks ◽  
Control Method ◽  
Low Voltage ◽  
Control Unit ◽  
Distribution Networks ◽  
Optimal Operation ◽  
Positive Sequence ◽  
Measurement Unit ◽  
Control Units ◽  
Three Phase

Three-phase imbalance is a long-term issue existing in low-voltage distribution networks (LVDNs), which consequently has an inverse impact on the safe and optimal operation of LVDNs. Recently, the increasing integration of single-phase distributed generations (DGs) and flexible loads has increased the probability of imbalance occurrence in LVDNs. To overcome the above challenges, this paper proposes a novel methodology based on the concept of "Active Asymmetry Energy-Absorbing (AAEA)" utilizing loads with a back-to-back converter, denoted as “AAEA Unit” in this paper. AAEA Units are deployed and coordinated to actively absorb asymmetry power among three phases for imbalance mitigation in LVDNs based on the high-precision, high-accuracy, and real-time distribution-level phasor measurement unit (D-PMU) data acquisition system and the 5th generation mobile networks (5G) communication channels. Furthermore, the control scheme of the proposed method includes three control units. Specifically, the positive-sequence control unit is designed to maintain the voltage of the DC-capacitor of the back-to-back converter. Likewise, the negative-sequence and zero-sequence control units are expected to mitigate the imbalanced current components. A simple imbalanced LVDN is modeled and tested in Simulink/Matlab (MathWorks, US). The obtained results demonstrate the effectiveness of the proposed methodology.

An Improved Three-Phase Buck Rectifier with Low Voltage Stress on Switching Devices

2020 ◽  
pp. 1-1
Author(s):  
Qiang Chen ◽  
Jianping Xu ◽  
Fei Zeng ◽  
Rui Huang ◽  
Lei Wang
Keyword(s):  
Low Voltage ◽  
Three Phase ◽  
Voltage Stress ◽  
Switching Devices

scholarly journals Modeling and Design of the Vector Control for a Three-Phase Single-Stage Grid-Connected PV System with LVRT Capability according to the Spanish Grid Code

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2899 ◽  
Author(s):  
Alexis B. Rey-Boué ◽  
N. F. Guerrero-Rodríguez ◽  
Johannes Stöckl ◽  
Thomas I. Strasser
Keyword(s):  
Vector Control ◽  
Reactive Power ◽  
Low Voltage ◽  
Single Stage ◽  
Photovoltaic System ◽  
Lookup Table ◽  
Voltage Sags ◽  
Pv System ◽  
Low Voltage Ride Through ◽  
Three Phase

This article deals with the vector control in dq axes of a three-phase grid-connected photovoltaic system with single-stage topology and low-voltage-ride-through capability. The photovoltaic generator is built using an array of several series-parallel Suntech PV modules and is modeled as a Lookup Table (two-dimensional; 2-D). The requirements adopted when grid voltage sags occur are based in both the IEC 61400-21 European normative and the allowed amount of reactive power to be delivered according to the Spanish grid code, which avoids the disconnection of the inverter under grid faults by a limitation in the magnitude of the three-phase output inverter currents. For this, the calculation of the positive- and negative-sequences of the grid voltages is made and a conventional three-phase Phase-Locked Loop is used for the inverter-grid synchronization, allowing the control of the active and reactive powers solely with the dq components of the inverter currents. A detailed enhanced flowchart of the control algorithm with low-voltage-ride-through capability is presented and several simulations and experiments using Matlab/SIMULINK and the Controller Hardware-in-the-Loop simulation technique, respectively, are run for several types of one- and three-phase voltage sags in order to validate its behavior.

scholarly journals Rancang Bangun Pengaman Panel Distribusi Tenaga Listrik Di Lippo Plaza Sidoarjo Dari Kebakaran Berbasis Arduino Nano

2017 ◽  
Vol 1 (2) ◽  
pp. 31
Author(s):  
Achmad Solih ◽  
Jamaaluddin Jamaaluddin
Keyword(s):  
Control System ◽  
Power Factor ◽  
Power Distribution ◽  
Low Voltage ◽  
Capacitor Bank ◽  
Warning Sign ◽  
Inductive Load ◽  
Three Phase ◽  
Working Principle ◽  
Power Distribution Control

Panel system power distribution at Lippo Plaza Mall Sidoarjo consists of several parts, namely from Cubicle 20 KV, 20 KV step-down transformer for 380 V, then the supply to LVMDP (Low Voltage Main Distribution Panel) The new panel to the user. Before delivery to users to note that the power factor is corrected using a capacitor bank. Less good a power factor is turned into inductive load on the capacitor bank so that temperatures high  because of high load resulting capacitor bank erupt. To overcome in this study proposes a safety panel automation power distribution control system using a microcontroller. Control system microcontrollers for safety panel power distribution consists of: Microcontroller (Arduino Nano), Light sensor (LDR), temperature sensor (LM35DZ), LCD 16x2 I2C, Actuators (fan, buzzer, relay switch breaker network three phase), switch ( relay 5 VDC), ADC as Input data. The working principle of this microcontroller LM35DZ if the sensor detects a high temperature fan will flash, if the LDR sensor detects sparks then the buzzer will sound as a warning sign of the dangers and disconnected the electricity network. From the design of a safety tool for power distribution panels due to high temperatures or sparks as well as the expected rate of fire outbreaks can be prevented.

Sign in / Sign up

Export Citation Format

Share Document