scholarly journals A Framework for Measuring the Time-Varying Shape and Full-Field Deformation of Residual Limbs Using 3-D Digital Image Correlation

2019 ◽  
Vol 66 (10) ◽  
pp. 2740-2752 ◽  
Author(s):  
Dana Solav ◽  
Kevin M. Moerman ◽  
Aaron M. Jaeger ◽  
Hugh M. Herr
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Image Correlation ◽  
Time Varying ◽  
Full Field

scholarly journals A framework for measuring the time-varying shape and full-field deformation of residual limbs using 3D digital image correlation

2019 ◽  
Author(s):  
Dana Solav ◽  
Kevin Mattheus Moerman ◽  
Aaron M. Jaeger ◽  
Hugh M. Herr
Keyword(s):  
High Resolution ◽  
Digital Image Correlation ◽  
Digital Image ◽  
Soft Tissues ◽  
Low Cost ◽  
Image Correlation ◽  
Time Varying ◽  
Residual Limb ◽  
Full Field ◽  
Prosthetic Socket

Effective prosthetic socket design following lower-limb amputation depends upon the accurate characterization of the shape of the residual limb as well as its volume and shape fluctuations. Objective: This study proposes a novel framework for the measurement and analysis of residual limb shape and deformation, using a high-resolution and low-cost system. Methods: A multi-camera system was designed to capture sets of simultaneous images of the entire residuum surface. The images were analyzed using a specially developed open-source three-dimensional digital image correlation (3D-DIC) toolbox, to obtain the accurate time-varying shapes as well as the full-field deformation and strain maps on the residuum skin surface. Measurements on a transtibial amputee residuum were obtained during knee flexions, muscle contractions, and swelling upon socket removal. Results: It was demonstrated that 3D-DIC can be employed to quantify with high resolution the time-varying residuum shapes, deformations, and strains. Additionally, the enclosed volumes and cross-sectional areas were computed and analyzed. Conclusion: This novel low-cost framework provides a promising solution for the in-vivo evaluation of residuum shapes and strains, as well as the potential for characterizing the mechanical properties of the underlying soft-tissues. Significance: These data may be used to inform data-driven computational algorithms for the design of prosthetic sockets, as well as of other wearable technologies mechanically interfacing with the skin.

scholarly journals Experimental Characterization of the FRCM-Concrete Interface Bond Behavior Assisted by Digital Image Correlation

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1154
Author(s):  
Dario De Domenico ◽  
Antonino Quattrocchi ◽  
Damiano Alizzio ◽  
Roberto Montanini ◽  
Santi Urso ◽  
...  
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Mechanical Tests ◽  
Image Correlation ◽  
Front Face ◽  
Full Field ◽  
Bond Behavior ◽  
Externally Bonded ◽  
Strengthening Technique ◽  
Concrete Interface

Digital Image Correlation (DIC) provides measurements without disturbing the specimen, which is a major advantage over contact methods. Additionally, DIC techniques provide full-field maps of response quantities like strains and displacements, unlike traditional methods that are limited to a local investigation. In this work, an experimental application of DIC is presented to investigate a problem of relevant interest in the civil engineering field, namely the interface behavior between externally bonded fabric reinforced cementitious mortar (FRCM) sheets and concrete substrate. This represents a widespread strengthening technique of existing reinforced concrete structures, but its effectiveness is strongly related to the bond behavior between composite fabric and underlying concrete. To investigate this phenomenon, a set of notched concrete beams are realized, reinforced with FRCM sheets on the bottom face, subsequently cured in different environmental conditions (humidity and temperature) and finally tested up to failure under three-point bending. Mechanical tests are carried out vis-à-vis DIC measurements using two distinct cameras simultaneously, one focused on the concrete front face and another focused on the FRCM-concrete interface. This experimental setup makes it possible to interpret the mechanical behavior and failure mode of the specimens not only from a traditional macroscopic viewpoint but also under a local perspective concerning the evolution of the strain distribution at the FRCM-concrete interface obtained by DIC in the pre- and postcracking phase.

The Stress Intensity Factor of Opening Mode Determined by Digital Image Correlation

2011 ◽  
Vol 83 ◽  
pp. 54-59 ◽  
Author(s):  
Rui Zhang ◽  
Ling Feng He ◽  
Chang Rong Li
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Digital Image Correlation ◽  
Intensity Factor ◽  
Digital Image ◽  
Correlation Method ◽  
Compact Tension ◽  
Image Correlation ◽  
Full Field ◽  
Opening Mode

Applications of the digital image correlation method (DIC) for the determination of the opening mode stress intensity factor (SIF) is investigated using an edge cracked aluminum plate in this paper. Standard compact tension test specimen was tested under tensile loading and the full-field displacement fields of the test sample were recorded using DIC. The SIF associated with unavoidable rigid-body displacement translation were calculated simultaneously from the experimental data by fitting the theoretical displacement field using the method of least-squares. Selection of displacement and convergence values is discussed. For validation, the SIF thus determined is compared with theoretical results, confirming the effectiveness and accuracy of the proposed technique. Therefore it reveals that the DIC is a practical and effective tool for full-field deformation and SIF measurement.

scholarly journals Novel Boundary Edge Detection for Accurate 3D Surface Profilometry Using Digital Image Correlation

2018 ◽  
Vol 8 (12) ◽  
pp. 2541 ◽  
Author(s):  
Liang-Chia Chen ◽  
Ching-Wen Liang
Keyword(s):  
Digital Image Correlation ◽  
Edge Detection ◽  
Digital Image ◽  
Optical Diffraction ◽  
Image Correlation ◽  
Detection Accuracy ◽  
Boundary Edge ◽  
Discontinuous Surface ◽  
Full Field ◽  
Surface Profilometry

Digital image correlation (DIC) has emerged as a popular full-field surface profiling technique for analyzing both in-plane and out-of-plane dynamic structures. However, conventional DIC-based surface 3D profilometry often yields erroneous contours along surface edges. Boundary edge detection remains one of the key issues in DIC because a discontinuous surface edge cannot be detected due to optical diffraction and height ambiguity. To resolve the ambiguity of edge measurement in optical surface profilometry, this study develops a novel edge detection approach that incorporates a new algorithm using both the boundary subset and corner subset for accurate edge reconstruction. A pre-calibrated gauge block and a circle target were reconstructed to prove the feasibility of the proposed approach. Experiments on industrial objects with various surface reflective characteristics were also conducted. The results showed that the developed method achieved a 15-fold improvement in detection accuracy, with measurement error controlled within 1%.

Sign in / Sign up

Export Citation Format

Share Document