Analysis of a Rectangular Waveguide, Edge Slot Array With Finite Wall Thickness

2007 ◽  
Vol 55 (3) ◽  
pp. 812-819 ◽  
Author(s):  
John C. Young ◽  
Jiro Hirokawa ◽  
Makoto Ando
Keyword(s):  
Wall Thickness ◽  
Rectangular Waveguide

Analysis of edge slots in rectangular waveguide with finite waveguide wall thickness

1996 ◽  
Vol 44 (8) ◽  
pp. 1120-1126 ◽  
Author(s):  
Cheng-Geng Jan ◽  
Ruey-Beei Wu ◽  
Powen Ilsu ◽  
Dau-Chyrh Chang
Keyword(s):  
Wall Thickness ◽  
Rectangular Waveguide ◽  
Waveguide Wall

Assessment of Myocardial Viability in Persistent Defects on Thallium-201 SPECT after Reinjection Using Gradient-Echo MRI

1996 ◽  
Vol 35 (05) ◽  
pp. 146-152 ◽  
Author(s):  
A. Kögler ◽  
H.-A. Schmitt ◽  
D. Emrich ◽  
H. Kreuzer ◽  
D. L. Munz ◽  
...  
Keyword(s):  
Wall Thickness ◽  
Myocardial Viability ◽  
Cardiac Cycle ◽  
Single Photon ◽  
Contractile Function ◽  
Left Ventricular ◽  
Wall Thickening ◽  
Gradient Echo ◽  
Systolic Wall Thickening

SummaryThis prospective study assessed myocardial viability in 30 patients with coronary heart disease and persistent defects despite reinjection on TI-201 single-photon computed tomography (SPECT). In each patient, three observers graded TI-201 uptake in 7 left ventricular wall segments. Gradient-echo magnetic resonance imaging in the region of the persistent defect generated 12 to 16 short axis views representing a cardiac cycle. A total of 120 segments were analyzed. Mean end-diastolic wall thickness and systolic wall thickening (± SD) was 11.5 ± 2.7 mm and 5.8 ± 3.9 mm in 48 segments with normal TI-201 uptake, 10.1 ± 3.4 mm and 3.7 ± 3.1 mm in 31 with reversible lesions, 11.3 ± 2.8 mm and 3.3 ± 1.9 mm in 10 with mild persistent defects, 9.2 ± 2.9 mm and 3.2 ±2.2 mm in 15 with moderate persistent defects, 5.8 ± 1.7 mm and 1.3 ± 1.4 mm in 16 with severe persistent defects, respectively. Significant differences in mean end-diastolic wall thickness (p <0.0005) and systolic wall thickening (p <0.005) were found only between segments with severe persistent defects and all other groups, but not among the other groups. On follow-up in 11 patients after revascularization, 6 segments with mild-to-moderate persistent defects showed improvement in mean systolic wall thickening that was not seen in 6 other segments with severe persistent defects. These data indicate that most myocardial segments with mild and moderate persistent TI-201 defects after reinjection still contain viable tissue. Segments with severe persistent defects, however, represent predominantly nonviable myocardium without contractile function.

CT Measurement of Wall Thickness of Early Gastric Cancer: Correlation with Upper GI Series

1995 ◽  
Vol 32 (3) ◽  
pp. 453
Author(s):  
Sung Hoon Chung ◽  
Hyun Sook Kim ◽  
In Oak Ahn ◽  
Goo Lee ◽  
Joon Hee Joh
Keyword(s):  
Gastric Cancer ◽  
Early Gastric Cancer ◽  
Wall Thickness ◽  
Upper Gi ◽  
Upper Gi Series ◽  
Ct Measurement

Performance study of RTV-2 Silicone Rubber Material For Soft Actuator by Experimental and Numerical methods: The Effect of Inflation Pressure and Wall Thickness

2020 ◽  
Vol 17 (1) ◽  
pp. 7524-7532 ◽  
Author(s):  
Deepak D. ◽  
Nitesh Kumar ◽  
Shreyas P. Shetty ◽  
Saurabh Jain ◽  
Manoj Bhat
Keyword(s):  
Numerical Methods ◽  
Wall Thickness ◽  
Silicone Rubber ◽  
Inflation Pressure ◽  
Performance Study ◽  
Rubber Material ◽  
Soft Actuator ◽  
Alternative Materials ◽  
Load Carrying ◽  
Influential Parameters

The expensive nature of currently used materials in the soft robotic industry demands the consideration of alternative materials for fabrication. This work investigates the performance of RTV-2 grade silicone rubber for fabrication of a soft actuator. Initially, a cylindrical actuator is fabricated using this material and its performance is experimentally assessed for different pressures. Further, parametric variations of the effect of wall thickness and inflation pressure are studied by numerical methods. Results show that, both wall thickness and inflation pressure are influential parameters which affect the elongation behaviour of the actuator. Thin (1.5 mm) sectioned actuators produced 76.97% more elongation compared to thick sectioned, but the stress induced is 89.61 % higher. Whereas, the thick sectioned actuator (6 mm) showed a higher load transmitting capability. With change in wall thickness from 1.5 mm to 6 mm, the elongation is reduced by 76.97 %, 38.35 %, 21.05 % and 11.43 % at pressure 100 kPa, 75 kPa, 50 kPa and 25 kPa respectively. The induced stress is also found reduced by 89.61 %, 86.66 %, 84.46 % and 68.68 % at these pressures. The average load carrying capacity of the actuator is found to be directly proportional to its wall thickness and inflation pressure.

Sign in / Sign up

Export Citation Format

Share Document