Layout-aware gate-sizing and buffer insertion for low-power low-noise DSM circuits

2004 ◽  
Author(s):  
A. Mukhejee ◽  
R. Sankaranarayan ◽  
K.R. Dusety
Keyword(s):  
Low Power ◽  
Low Noise ◽  
Gate Sizing ◽  
Buffer Insertion

A Low Power and Low Noise On-Chip Active RF Tracking Filter for Digital TV Tuner ICs

2011 ◽  
Vol E94-C (10) ◽  
pp. 1698-1701
Author(s):  
Yang SUN ◽  
Chang-Jin JEONG ◽  
In-Young LEE ◽  
Sang-Gug LEE
Keyword(s):  
Low Power ◽  
Digital Tv ◽  
Low Noise ◽  
On Chip ◽  
Tracking Filter

A low noise and low power device composed of electrode and CD ASIC for neural and other vital signals recording

2021 ◽  
Vol 324 ◽  
pp. 112681
Author(s):  
Jianhui Sun ◽  
Zibin Wang ◽  
Tongxi Wang ◽  
Guozhu Liu ◽  
Jiangwei Tian
Keyword(s):  
Low Power ◽  
Low Noise ◽  
Power Device

Tunable Low-Power Low-Noise Amplifier for Healthcare Applications

2021 ◽  
Author(s):  
Rafael Vieira ◽  
Nuno Horta ◽  
Nuno Lourenço ◽  
Ricardo Póvoa
Keyword(s):  
Low Power ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Healthcare Applications ◽  
Noise Amplifier

A Low-Noise, Low-Power, Wide Dynamic Range Logarithmic Amplifier for Biomedical Applications

2018 ◽  
Vol 27 (07) ◽  
pp. 1850104 ◽  
Author(s):  
Yuwadee Sundarasaradula ◽  
Apinunt Thanachayanont
Keyword(s):  
Low Power ◽  
Biomedical Applications ◽  
Dynamic Range ◽  
Supply Voltage ◽  
Low Noise ◽  
Power Supply Voltage ◽  
Wide Dynamic Range ◽  
Dc Offset ◽  
Limiting Amplifier ◽  
Logarithmic Amplifier

This paper presents the design and realization of a low-noise, low-power, wide dynamic range CMOS logarithmic amplifier for biomedical applications. The proposed amplifier is based on the true piecewise linear function by using progressive-compression parallel-summation architecture. A DC offset cancellation feedback loop is used to prevent output saturation and deteriorated input sensitivity from inherent DC offset voltages. The proposed logarithmic amplifier was designed and fabricated in a standard 0.18[Formula: see text][Formula: see text]m CMOS technology. The prototype chip includes six limiting amplifier stages and an on-chip bias generator, occupying a die area of 0.027[Formula: see text]mm2. The overall circuit consumes 9.75[Formula: see text][Formula: see text]W from a single 1.5[Formula: see text]V power supply voltage. Measured results showed that the prototype logarithmic amplifier exhibited an 80[Formula: see text]dB input dynamic range (from 10[Formula: see text][Formula: see text]V to 100[Formula: see text]mV), a bandwidth of 4[Formula: see text]Hz–10[Formula: see text]kHz, and a total input-referred noise of 5.52[Formula: see text][Formula: see text]V.

scholarly journals A 60 GHz fully differential LNA in 90 nm CMOS technology

2013 ◽  
Vol 6 (2) ◽  
pp. 109-113 ◽  
Author(s):  
Andrea Malignaggi ◽  
Amin Hamidian ◽  
Georg Boeck
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Transmission Lines ◽  
Noise Figure ◽  
Design Procedure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
60 Ghz ◽  
Fully Differential

The present paper presents a fully differential 60 GHz four stages low-noise amplifier for wireless applications. The amplifier has been optimized for low-noise, high-gain, and low-power consumption, and implemented in a 90 nm low-power CMOS technology. Matching and common-mode rejection networks have been realized using shielded coplanar transmission lines. The amplifier achieves a peak small-signal gain of 21.3 dB and an average noise figure of 5.4 dB along with power consumption of 30 mW and occupying only 0.38 mm2pads included. The detailed design procedure and the achieved measurement results are presented in this work.

Sign in / Sign up

Export Citation Format

Share Document