Surfactant treated drop-coated polyethylene adipate \ carbon black nanocomposite sensor for alcohol vapour detection

2006 ◽  
Author(s):  
K. Arshak ◽  
E.G. Moore ◽  
C. Cunniffe
Keyword(s):  
Carbon Black ◽  
Nanocomposite Sensor ◽  
Alcohol Vapour

Mechanistic Approach for Long-Term Stability of a Polyethylene Glycol–Carbon Black Nanocomposite Sensor

ACS Sensors ◽  
2021 ◽  
Author(s):  
Wenjun Li ◽  
Kazuki Nagashima ◽  
Takuro Hosomi ◽  
Chen Wang ◽  
Yosuke Hanai ◽  
...  
Keyword(s):  
Polyethylene Glycol ◽  
Carbon Black ◽  
Term Stability ◽  
Long Term Stability ◽  
Mechanistic Approach ◽  
Nanocomposite Sensor

An ultra-thin printable nanocomposite sensor network for structural health monitoring

2019 ◽  
pp. 147592171985933 ◽  
Author(s):  
Yaozhong Liao ◽  
Pengyu Zhou ◽  
Dongyue Pan ◽  
Li-min Zhou ◽  
Zhongqing Su
Keyword(s):  
Structural Health Monitoring ◽  
Carbon Black ◽  
Sensor Network ◽  
Health Monitoring ◽  
Ultrasonic Waves ◽  
Polyvinyl Pyrrolidone ◽  
Superior Performance ◽  
Engineering Structures ◽  
Structural Health ◽  
Nanocomposite Sensor

A nanocomposite-based sensor ink made from carbon black and polyvinyl pyrrolidone was developed for fabricating a new breed of sensor by an inkjet printing approach, to accommodate the general purposes of structural health monitoring. This ink can be directly deposited onto the surface of various substrates or engineering structures such as polyimide film via computer-aided design to configure nanocomposite sensor arrays or dense sensor networks. Strong structure adaptability and high flexibility make this sensor a promising candidate to alternate traditional piezoresistive and piezoelectric sensors, in signal acquisition of dynamic disturbance on complex engineering structures. Lightweight and without the need to use wires or cables, the printed sensor network significantly reduces the weight and volume penalty imposed on the host structures, even when the network is deployed at a large scale. It also minimizes the possibility of exfoliation of the sensors from the host structure under cyclic load. The printed pattern distinguishes superior performance in the perception of acousto-ultrasonic signals from static up to 500 kHz, with high signal-to-noise ratio, sensitivity, and fidelity. By virtue of the tunneling current between two adjacent nanoparticles that are in close proximity (within several nanometers), the printed sensor network is capable of perceiving ultrasonic waves. The fabrication process of the sensor network does not entail any specially made printing facilities, and the carbon black/polyvinyl pyrrolidone hybrid can easily be injected into an inkjet cartridge for printing. Several confirmatory experiments and a proof-of-concept test were carried out based on the printed sensor network to validate the capability of the printed sensor for structural health monitoring.

A Preparation of High Resolution Standards for Electron Microscopy. Part II

1971 ◽  
Vol 29 ◽  
pp. 160-161
Author(s):  
Akira Tanaka ◽  
David F. Harling
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Carbon Black ◽  
Single Crystal ◽  
Dark Field ◽  
Graphitized Carbon Black ◽  
Graphitized Carbon ◽  
Dark Field Imaging ◽  
Crystal Films ◽  
Micro Holes

In the previous paper, the author reported on a technique for preparing vapor-deposited single crystal films as high resolution standards for electron microscopy. The present paper is intended to describe the preparation of several high resolution standards for dark field microscopy and also to mention some results obtained from these studies. Three preparations were used initially: 1.) Graphitized carbon black, 2.) Epitaxially grown particles of different metals prepared by vapor deposition, and 3.) Particles grown epitaxially on the edge of micro-holes formed in a gold single crystal film.The authors successfully obtained dark field micrographs demonstrating the 3.4Å lattice spacing of graphitized carbon black and the Au single crystal (111) lattice of 2.35Å. The latter spacing is especially suitable for dark field imaging because of its preparation, as in 3.), above. After the deposited film of Au (001) orientation is prepared at 400°C the substrate temperature is raised, resulting in the formation of many square micro-holes caused by partial evaporation of the Au film.

Extraction and identification of fillers and pigments from pyrolyzed rubber and tire samples

1996 ◽  
Vol 54 ◽  
pp. 174-175
Author(s):  
P. Sadhukhan ◽  
J. B. Zimmerman
Keyword(s):  
Zinc Oxide ◽  
Electron Microscope ◽  
Carbon Black ◽  
Natural Rubber ◽  
Transmission Electron Microscope ◽  
Rolling Resistance ◽  
Synthetic Polymers ◽  
Nitrogen Atmosphere ◽  
Transmission Electron ◽  
Curing Agents

Rubber stocks, specially tires, are composed of natural rubber and synthetic polymers and also of several compounding ingredients, such as carbon black, silica, zinc oxide etc. These are generally mixed and vulcanized with additional curing agents, mainly organic in nature, to achieve certain “designing properties” including wear, traction, rolling resistance and handling of tires. Considerable importance is, therefore, attached both by the manufacturers and their competitors to be able to extract, identify and characterize various types of fillers and pigments. Several analytical procedures have been in use to extract, preferentially, these fillers and pigments and subsequently identify and characterize them under a transmission electron microscope.Rubber stocks and tire sections are subjected to heat under nitrogen atmosphere to 550°C for one hour and then cooled under nitrogen to remove polymers, leaving behind carbon black, silica and zinc oxide and 650°C to eliminate carbon blacks, leaving only silica and zinc oxide.

Sign in / Sign up

Export Citation Format

Share Document