Numerical investigation in cold flow field on the influence of the injection velocity from the center body of the trapped vortex combustor

2011 ◽  
Author(s):  
Shiqing Liu ◽  
Jingjun Zhong
Keyword(s):  
Flow Field ◽  
Numerical Investigation ◽  
Injection Velocity ◽  
Cold Flow ◽  
Trapped Vortex ◽  
Center Body

scholarly journals Numerical Investigation of Flow Field Near the Exhaust Opening Indoor

2019 ◽  
Vol 267 ◽  
pp. 032081
Author(s):  
Chanjun Meng ◽  
Bo Yuan ◽  
Chuan He ◽  
Chunfu Xi ◽  
Liangming Pan
Keyword(s):  
Flow Field ◽  
Numerical Investigation

Numerical Studies on Trapped-Vortex Concepts for Stable Combustion

1998 ◽  
Vol 120 (1) ◽  
pp. 60-68 ◽  
Author(s):  
V. R. Katta ◽  
W. M. Roquemore
Keyword(s):  
Drag Coefficient ◽  
Reacting Flow ◽  
Flow Conditions ◽  
Third Order ◽  
Cold Flow ◽  
Flow Simulations ◽  
Numerical Studies ◽  
Dynamic Flows ◽  
Experimental Findings ◽  
Trapped Vortex

Spatially locked vortices in the cavities of a combustor aid in stabilizing the flames. On the other hand, these stationary vortices also restrict the entrainment of the main air into the cavity. For obtaining good performance characteristics in a trapped-vortex combustor, a sufficient amount of fuel and air must be injected directly into the cavity. This paper describes a numerical investigation performed to understand better the entrainment and residence-time characteristics of cavity flows for different cavity and spindle sizes. A third-order-accurate time-dependent Computational Fluid Dynamics with Chemistry (CFDC) code was used for simulating the dynamic flows associated with forebody-spindle-disk geometry. It was found from the nonreacting flow simulations that the drag coefficient decreases with cavity length and that an optimum size exists for achieving a minimum value. These observations support the earlier experimental findings of Little and Whipkey (1979). At the optimum disk location, the vortices inside the cavity and behind the disk are spatially locked. It was also found that for cavity sizes slightly larger than the optimum, even though the vortices are spatially locked, the drag coefficient increases significantly. Entrainment of the main flow was observed to be greater into the smaller-than-optimum cavities. The reacting-flow calculations indicate that the dynamic vortices developed inside the cavity with the injection of fuel and air do not shed, even though the cavity size was determined based on cold-flow conditions.

Enhanced vortex stability in trapped vortex combustor

2010 ◽  
Vol 114 (1155) ◽  
pp. 333-337 ◽  
Author(s):  
S. Vengadesan ◽  
C. Sony
Keyword(s):  
Numerical Simulation ◽  
Vortex Flow ◽  
Cavity Size ◽  
Vortex Stability ◽  
Cold Flow ◽  
Air Jets ◽  
Passive Flow ◽  
Flow Through ◽  
Trapped Vortex ◽  
Driver Air

Abstract The Trapped Vortex Combustor (TVC) is a new design concept in which cavities are designed to trap a vortex flow structure established through the use of driver air jets located along the cavity walls. TVC offers many advantages when compared to conventional swirl-stabilised combustors. In the present work, numerical investigation of cold flow (non-reacting) through the two-cavity trapped vortex combustor is performed. The numerical simulation involves passive flow through the two-cavity TVC to obtain an optimum cavity size to trap stable vortices inside the second cavity and to observe the characteristics of the two cavity TVC. From the flow attributes, it is inferred that vortex stability is achieved by circulation and the vortex is trapped inside when a second afterbody is added.

Numerical Investigation of a Fiber Web Effect on the Pressure Drop and Particles Collection in a Microchannel

2009 ◽  
Author(s):  
Alireza Dastan ◽  
Omid Abouali
Keyword(s):  
Pressure Drop ◽  
Flow Field ◽  
Numerical Investigation ◽  
Particle Motion ◽  
Particle Deposition ◽  
Hydraulic Diameter ◽  
Lagrangian Approach ◽  
Computational Domain ◽  
Governing Equations ◽  
Eulerian Approach

In this paper pressure drop and particle deposition in a microchannel with a hydraulic diameter of 225 micrometer is investigated numerically. Several hundred micron length fibers caught at the entrance of the channels making a “fiber web” also is modeled in this research. Governing equations for the flow field are solved with an Eulerian approach while the equations of particle motion in the flow are solved by a Lagrangian approach. Assuming the symmetry in the domain, one channel and the corresponding plenum are studied in the computational domain. For studying the effects of fibers in the flow, two fiber webs with four and six solid fibers are studied. The increase of pressure drop in the microchannel because of the entrance fiber web is computed and discussed. Also deposition and collection of the particles with various diameters at the fiber webs are also presented.

Experimental and numerical investigation on the flow field within a compact inlet duct

2013 ◽  
Vol 44 ◽  
pp. 478-488 ◽  
Author(s):  
John C. Vaccaro ◽  
Yossef Elimelech ◽  
Yi Chen ◽  
Onkar Sahni ◽  
Kenneth E. Jansen ◽  
...  
Keyword(s):  
Flow Field ◽  
Numerical Investigation ◽  
Inlet Duct
Sign in / Sign up

Export Citation Format

Share Document