A Memristor Device Model

2011 ◽  
Vol 32 (10) ◽  
pp. 1436-1438 ◽  
Author(s):  
Chris Yakopcic ◽  
Tarek M. Taha ◽  
Guru Subramanyam ◽  
Robinson E. Pino ◽  
Stanley Rogers
Keyword(s):  
Device Model ◽  
Memristor Device

Consistent Device Model of a Perovskite Solar Cell for Multiple Experiments

2019 ◽  
Author(s):  
Evelyne Knapp ◽  
Andreas Schiller ◽  
Martin T. Neukom ◽  
Simon Züfle ◽  
Beat Ruhstaller
Keyword(s):  
Solar Cell ◽  
Perovskite Solar Cell ◽  
Device Model

Failure Analysis of CDM-ESD Damage in a GaAs RFIC

2000 ◽  
Author(s):  
Amy Poe ◽  
Steve Brockett ◽  
Tony Rubalcava
Keyword(s):  
Radio Frequency ◽  
Failure Analysis ◽  
Integrated Circuit ◽  
Production Test ◽  
Analysis Techniques ◽  
Device Model ◽  
Charged Device ◽  
Subsequent Failure

Abstract The intent of this work is to demonstrate the importance of charged device model (CDM) ESD testing and characterization by presenting a case study of a situation in which CDM testing proved invaluable in establishing the reliability of a GaAs radio frequency integrated circuit (RFIC). The problem originated when a sample of passing devices was retested to the final production test. Nine of the 200 sampled devices failed the retest, thus placing the reliability of all of the devices in question. The subsequent failure analysis indicated that the devices failed due to a short on one of two capacitors, bringing into question the reliability of the dielectric. Previous ESD characterization of the part had shown that a certain resistor was likely to fail at thresholds well below the level at which any capacitors were damaged. This paper will discuss the failure analysis techniques which were used and the testing performed to verify the failures were actually due to ESD, and not caused by weak capacitors.

Analysis of an Anomalous CMOS Transistor Exhibiting Drain to Source Leakage—Its Model and Cause

2014 ◽  
Author(s):  
Yuk L. Tsang ◽  
Alex VanVianen ◽  
Xiang D. Wang ◽  
N. David Theodore
Keyword(s):  
Threshold Voltage ◽  
Crystalline Silicon ◽  
Electrical Characterization ◽  
Visual Defect ◽  
Scanning Capacitance Microscopy ◽  
Device Model ◽  
Graphical Simulation ◽  
Cmos Transistor

Abstract In this paper, we report a device model that has successfully described the characteristics of an anomalous CMOS NFET and led to the identification of a non-visual defect. The model was based on detailed electrical characterization of a transistor exhibiting a threshold voltage (Vt) of about 120mv lower than normal and also exhibiting source to drain leakage. Using a simple graphical simulation, we predicted that the anomalous device was a transistor in parallel with a resistor. It was proposed that the resistor was due to a counter doping defect. This was confirmed using Scanning Capacitance Microscopy (SCM). The dopant defect was shown by TEM imaging to be caused by a crystalline silicon dislocation.

scholarly journals CDM Protection Test Structure for I/O Cells in a Submicronic Technology

Electronics ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 443
Author(s):  
Mihaela-Daniela Dobre ◽  
Philippe Coll ◽  
Gheorghe Brezeanu
Keyword(s):  
Electrostatic Discharge ◽  
New Technology ◽  
Test Chip ◽  
Technology Node ◽  
Ground Resistance ◽  
Maximum Resistance ◽  
Device Model ◽  
Protection Method ◽  
Esd Protection ◽  
Protection Devices

This paper proposes an investigation of a CDM (charge device model) electrostatic discharge (ESD) protection method used in submicronic input–output (I/O) structures. The modeling of the commonly used ESD protection devices as well as the modeling of the breakdown caused by ESD is not accurate using traditional commercial tools, hence the need for test-chip implementation, whenever a new technology node is used in production. The proposed method involves defining, implementing, testing, and concluding on one test-chip structure named generically “CDM ground resistance”. The structure assesses the maximum ground resistance allowed for the considered technology for which CDM protection is assured. The findings are important because they will be actively used as CDM protection for all I/O structures developed in the considered submicronic technology node. The paper will conclude on the constraints in terms of maximum resistance of ground metal track allowed to be CDM protected.

Sign in / Sign up

Export Citation Format

Share Document