scholarly journals Clustered multithreaded architectures -pursuing both IPC and cycle time

2004 ◽  
Author(s):  
J.D. Collins ◽  
D.M. Tullsen
Keyword(s):  
Cycle Time ◽  
Multithreaded Architectures

Design of spline surface vacuum gripper for pick and place robotic arms

2020 ◽  
Vol 4 (2) ◽  
pp. 48-55
Author(s):  
A. S. Jamaludin ◽  
M. N. M. Razali ◽  
N. Jasman ◽  
A. N. A. Ghafar ◽  
M. A. Hadi
Keyword(s):  
Cycle Time ◽  
Industrial Robot ◽  
Annealing Process ◽  
Vacuum Suction ◽  
Robotic Arms ◽  
Custom Made ◽  
Pick And Place ◽  
Manufacturing Procedure ◽  
Production Flexibility ◽  
The Impact

The gripper is the most important part in an industrial robot. It is related with the environment around the robot. Today, the industrial robot grippers have to be tuned and custom made for each application by engineers, by searching to get the desired repeatability and behaviour. Vacuum suction is one of the grippers in Watch Case Press Production (WCPP) and a mechanism to improve the efficiency of the manufacturing procedure. Pick and place are the important process for the annealing process. Thus, by implementing vacuum suction gripper, the process of pick and place can be improved. The purpose of vacuum gripper other than design vacuum suction mechanism is to compare the effectiveness of vacuum suction gripper with the conventional pick and place gripper. Vacuum suction gripper is a mechanism to transport part and which later sequencing, eliminating and reducing the activities required to complete the process. Throughout this study, the process pick and place became more effective, the impact on the production of annealing process is faster. The vacuum suction gripper can pick all part at the production which will lower the loss of the productivity. In conclusion, vacuum suction gripper reduces the cycle time about 20%. Vacuum suction gripper can help lower the cycle time of a machine and allow more frequent process in order to increase the production flexibility.

Breakthrough on Routine Service Cycle Time Improvement – Leap Frog Concept, Duri Field, Indonesia

2020 ◽  
Author(s):  
R. Irawan
Keyword(s):  
Cycle Time ◽  
Critical Path ◽  
Well Control ◽  
Routine Service ◽  
New Process ◽  
Work Concept ◽  
Preparation Step ◽  
One Step ◽  
Time Average ◽  
Moving Process

Leap frog concept was created to address the loss of single joint rig agility and drive the cycle time average lower than ever. The idea is to move the preparation step into a background activity that includes moving the equipment, killing the well, dismantling the wellhead and installing the well control equipment/BOP before the rig came in. To realize the idea, a second set of equipment is provided along with the manpower. By moving the preparation step, the goal is to eliminate a 50% portion of the job from the critical path. The practice is currently performed in tubing pump wells on land operations. However, the work concept could be implemented for other type of wells, especially ESP wells. After implementation, the cycle time average went down from 18 hours to 11 hours per job, or down by ~40%. The toolpusher also reports more focused operations due to reduced scope and less crew to work with, making the leap frog operation safer and more reliable. Splitting the routine services into 2 parts not only shortened the process but it also reduces noise that usually appear in the preparation process. The team are rarely seen waiting on moving support problems that were usually seen in the conventional process. Having the new process implemented, the team had successfully not only lowered cycle time, but also eliminated several problems in one step. Other benefits from leap frog implementation is adding rig count virtually to the actual physical rig available on location, and also adding rig capacity and completing more jobs compared to the conventional rig. In other parts, leap frog faced some limitation and challenges, such as: limited equipment capability for leap frog remote team to work on stuck plunger, thus hindering its leap frog capability, and working in un-restricted/un-clustered area which disturb the moving process and operation safety.

IMPROVEMENT LAYOUT AND ELEMENTS WORK IN ERGONOMIC ASPECTS

2012 ◽  
Vol 2 (2) ◽  
pp. 84-99
Author(s):  
Beci Sariani ◽  
Meizul Zuki ◽  
Yusril Dany
Keyword(s):  
Working Conditions ◽  
Cycle Time ◽  
Completion Time ◽  
Content Creation ◽  
Left Hand ◽  
Total Distance ◽  
Standard Time ◽  
Before And After ◽  
Right And Left Hand

The purpose of this study is to describe layout and elements of the movement labor, determine cake making job completion time before and after repair, complaints of pain workers and recomendation improved layout and elements work in ergonomic aspects. Layout and elements of the cake making job is less visible than ergonomic working conditions with temperatures as high as 290C and 300C, total distance moving much material for the production namely 2407 cm, manufacture molen 180 cm, 2926 cm baking and packaging 626 cm. Percentage of use right and left hand at creation pia cake is 50.11% and 54.4%. Making molen is 100% and 76.69%. Pia cake making is 12.76% and 12.21%. Packaging is 100% and 84.8%. Cycle time, normal time and standard time of content creation, namely 17004.15, 18.534.52 and 25.577.64 seconds (2 basins). Making molen is 560.23, 616.25 and 751.82 seconds (1 basin). Pia cake making is 1.165,45, 1314.63 and 1.603,85 seconds (2 trays), and packaging is 15,40, 16,79 and 23.17 seconds (2 pack). The application of ergonomics : 8 types of grievances felt a bit sick and 1 type of grievances felt sick. Station molen manufacture, workers felt no pain. Baking station pia (sub-stations) only complaint molen rolling on his back felt a little sore. Sub-station charging only 3 workers who feel a little pain complaints and pain. In the sub-station : 6 types pengovenan grievances felt a little sick. The packing station after repairs only felt a little pain in the waist

LADA Synchronization for Symmetric and Asymmetric ATE Test Program Cycles

2019 ◽  
Author(s):  
Arun Kumar Karunanithi ◽  
Joseph Caroselli ◽  
Jason Christensen ◽  
Michell Espitia
Keyword(s):  
Cycle Time ◽  
Dwell Time ◽  
Turnaround Time ◽  
Test Program ◽  
Area Of Interest ◽  
Marginal State ◽  
Structural Failures ◽  
Major Factors ◽  
High Level ◽  
Program Cycle

Abstract Laser Assisted Device Alteration (LADA) or Soft Defect Localization (SDL) is commonly used to root cause device marginality due to functional or structural failures. At a high level, LADA involves setting the device under test (DUT) at its marginal state and using focused near infra-red laser beams to perturb sensitive circuitry [1]. Scanning the focused laser beam over the die can be a long and time-consuming process. In this paper, two LADA cases are presented, which involve a parametric measurement failure while running a dynamic ATE test. Using LADA technique, these two cases were root caused. These two cases also explain how a parametric measurement-based LADA can be setup on ATE, as well as a synchronization method independent of vectors in a pattern. Synchronization was necessitated in the 2nd case due to the asymmetric test program loop, as well as the long test program cycle time. There are many factors which impact LADA turnaround time and it can take anywhere between few seconds to one day. The two major factors are the size of the Area of Interest (AOI) and test program cycle time. Test program cycle time influences the laser “dwell time” for LADA. Dwell time, in simple terms, is the total time the laser is parked at each pixel. The laser can also be synchronized with the test program cycle, keeping the two always in phase. This is explained in Case 2, where LADA synchronization was implemented, and the analysis was successfully completed in time, even though the test cycle time was very long.

Optimal Inventory Policies for Price and Time Sensitive Demand under Advertisement

2020 ◽  
Vol 13 ◽  
Author(s):  
Nita Shah ◽  
Ekta Patel ◽  
Kavita Rabari
Keyword(s):  
Cycle Time ◽  
Quadratic Function ◽  
Solution Procedure ◽  
Vital Role ◽  
Optimal Number ◽  
Deteriorating Items ◽  
Marginal Effect ◽  
Selling Price ◽  
Total Profit ◽  
Back Order

Aims: This article analyzes an inventory system for deteriorating items. The demand is quadratic function of time and is dependent on time, price and advertisement. Shortages are allowed and partially backlogged. Background: Demand and pricing are the two most crucial factors in inventory policy for any business to be successful. In today’s era of competitive circumstances, any product is promoted through advertisement, which plays a vital role in changing the demand pattern among the community. The marketing and demonstration of an item by time-to-time with fashionable advertisements through well-known media such as TV, radio, newspaper, magazine, etc. However, this idea is not always true for some goods like wheat, vegetables, fruits, food grains, medicines and other perishable goods due to their deteriorating nature and this in turn decreases demand for such goods. Deterioration may define as decay, damage, spoilage, evaporation, obsolescence, pilferage. Hence, deterioration effect is a major part in inventory control theory. So in this article demand rate is considered to be a function of selling price, time and occurrence of advertisement instantaneously. Objective: A solution procedure is obtained to find optimal number of price changes and optimal selling price to maximize the total profit. Method: Classical Optimization. Result: From the sensitivity analysis table, it can be seen that the optimal profit is highly sensible to advertisement coefficient and purchase cost. With an increment in rate of deterioration, selling price decreases. Scale demand has reasonable effect on cycle time and selling price. When the value of increase, the cycle length and profit goes on decreasing. Growth in profit is observed if we increase parameter b, higher will be the profit. Price elasticity is sensible parameter with respect to selling price. If backlogging rate increases, the profit will decreases. The inventory parameters holding cost, back order cost and lost sale cost have marginal effect on total profit. Conclusion: In this article, an inventory model is proposed for deteriorating items with variable demand depends upon the advertisement, selling price of the item and time. Shortages are allowed and partially backlogged and backlogging rate depends on the waiting time for the next replenishment. From this article, we can conclude that the parameters are insensible with respect to optimal profit, cycle time and selling price and rest of the parameters have practical output on total profit.

Sign in / Sign up

Export Citation Format

Share Document