Current harmonics mitigation using a modular multilevel converter-based shunt active power filter

2016 ◽  
Author(s):  
M.S. Hamad ◽  
K.H. Ahmed ◽  
A.I. Madi
Keyword(s):  
Active Power Filter ◽  
Active Power ◽  
Modular Multilevel Converter ◽  
Multilevel Converter ◽  
Shunt Active Power Filter ◽  
Current Harmonics ◽  
Power Filter

CURRENT HARMONICS MITIGATION FROM GRID CONNECTED VARIABLE SPEED WIND TURBINE DUE TO NONLINEAR LOADS USING SHUNT ACTIVE POWER FILTER

2017 ◽  
Vol 79 (4) ◽  
Author(s):  
Sajid Hussain Qazi ◽  
Mohd Wazir Mustafa ◽  
U. Sultana ◽  
Nayyar Hussain Mirjat
Keyword(s):  
Wind Turbine ◽  
Active Power Filter ◽  
Active Power ◽  
Variable Speed ◽  
Nonlinear Loads ◽  
Shunt Active Power Filter ◽  
Current Harmonics ◽  
Power Filter ◽  
Current Controller ◽  
Synchronous Reference Frame

The quality of power nowadays is of great concern due to increasing demand of supply and energy resources are limited, another cause is increasing penetration of nonlinear loads in the power system. In order to overcome energy supply challenges, the focus of technologists is shifting to the renewable energy side such as the wind and solar energy and so on. As such, mitigating effect of nonlinear loads have become ever important as well. In this context, various techniques have been used by researchers in past decades. Shunt active power filter (APF) have long been used to mitigate current harmonics from fixed wind turbine generator (WTG). In this study shunt APF has been applied with variable speed WTG using synchronous reference frame (SRF) for the extraction of compensation signal for APF. Gate driver signals are generated from Bang-Bang Controller (Hysteresis Band Current Controller HBCC). A MATLAB/SIMULINK based Model have been developed. The Simulation results show decreased THD levels of the system and clearly suggest the effectiveness of Shunt APF in meeting the IEEE-519 standard recommendation for harmonic levels in WTG.

Five-Level Cascaded H-Bridge MLC-Based Shunt Active Power Filter for Active Harmonics Mitigation in Distributed Network

2018 ◽  
Vol 28 (02) ◽  
pp. 1950035 ◽  
Author(s):  
Jitendra Tandekar ◽  
Amit Ojha ◽  
Shailendra Jain
Keyword(s):  
Pulse Width Modulation ◽  
Average Power ◽  
Active Power Filter ◽  
Active Power ◽  
Shunt Active Power Filter ◽  
Harmonic Compensation ◽  
Current Harmonics ◽  
Power Filter ◽  
Power Quality Improvement ◽  
Real Time Digital Simulator

This paper presents an investigation on mitigation of current harmonics, using Cascaded H-bridge Multilevel Converter (CHB-MLC)-based Shunt Active Power Filter (SAPF). Development and analysis of SAPF for harmonic compensation in distribution network for power quality improvement has been discussed. In the proposed work, transformer-less CHB MLC is used which reduces weight and cost of the system. Moreover, a novel controller based on average power method is adopted for generation of compensation active filter current. In order to generate switching signals, multi-carrier Alternate Phase Opposition Disposition (APOD) — Pulse Width Modulation (PWM) schemes are used. The proposed CHB-MLC SAPF reduces the source current THD below 5%. The results are simulated in MATLAB/Simulink and demonstrate the effective mitigation of current harmonics with APOD-PWM schemes. Opal-RT OP4500 real-time digital simulator is used to validate the proposed scheme under different steady state and transient conditions.

scholarly journals Source current harmonic mitigation of distorted voltage source by using shunt active power filter

2020 ◽  
Vol 10 (4) ◽  
pp. 3967
Author(s):  
Muhammad Ossama Mahmoud ◽  
Wael Mamdouh ◽  
Hamdy Khalil
Keyword(s):  
Input Signal ◽  
Active Power Filter ◽  
Active Power ◽  
Control Circuit ◽  
Voltage Source ◽  
Shunt Active Power Filter ◽  
Current Harmonics ◽  
Power Filter ◽  
Source Current ◽  
Source Voltage

In this paper, three-phase, four-wire shunt active power filter (SAPF) is utilized to mitigate system harmonics of distorted voltage source for unbalanced and nonlinear loads. Basically, the source voltage should be pure sinusoidal waveform to get a good mitigation of source current harmonics. In this under study system, the source voltage is assumed to be harmonic distortion non-sinusoidal voltage source. The phase locked loop (PLL) control circuit is wielded for extracting the fundamental component of the distorted source voltage to use it as an input signal to the SAPF control. Another input signal to the SAPF is the distorted load current. The SAPF control system uses (p-q) theory to calculate the optimum instantaneous current to be injected by the SAPF to mitigate the source current harmonics even the source voltage is harmonic distorted. MATLAB/SIMULINK software package is utilized to simulate the system under study. The effect of SAPF is tested when it’s used with and without the PLL control circuit. The simulation results show that, the THD of source current when using the PLL control circuit is improved to comply with the harmonic limits given in the IEEE 519-1992 and IEC 61000-4-7 standards.

Sign in / Sign up

Export Citation Format

Share Document