A Skew Detection Method for 2D Bar Code Images Based on the Least Square Method

2006 ◽  
Author(s):  
Ying-hong Liang ◽  
Zhi-yan Wang
Keyword(s):  
Detection Method ◽  
Least Square Method ◽  
Least Square ◽  
Bar Code ◽  
Skew Detection ◽  
2D Bar Code

scholarly journals An Enhanced Detection System of Drill Rod Bending Degree Based on Two-Dimensional Laser

Sensors ◽  
2020 ◽  
Vol 20 (2) ◽  
pp. 370
Author(s):  
Lingling Wu ◽  
Guojun Wen ◽  
Yudan Wang ◽  
Xinjian Xu
Keyword(s):  
Detection Method ◽  
Detection System ◽  
Least Square Method ◽  
Least Square ◽  
Two Dimensional ◽  
Optical Inspection ◽  
Section Shape ◽  
Mechanical Bending ◽  
Low Efficiency ◽  
Displacement Based

Drill rod straightness has to be strictly controlled and the maximum bending degree detection needs to be used in the straightening process. The mechanical bending degree measurement depends on machinery instruments and workers’ experience, often with low efficiency and precision. While the optical inspection, as a non-contact detection method, with higher precision and lower installation accuracy requirements, is frequently applied in the online detection system. Based on this, an enhanced bending degree detection system for a drill rod is proposed in this paper. Compared to the existing detection system, the main progress is to use a two-dimensional laser to quickly obtain arc profile data and fit with ellipse. Segment inspection idea is also utilized is this system as the camera that could obtain the whole drill rod in one shot needs extremely high resolution and price. A specialized algorithm is designed to fit the cross-section shape and whole centerline displacement based on the least square method. Some laboratory tests are conducted to verify this detection system, findings of which are compared to manual measured results. The maximum bending degree error is 2.14 mm and the maximum position error is 8.21 mm, which are both within the tolerance of error. Those results show the feasibility and precision of this enhanced detection system.

A Skew Detection Algorithm for PDF417 Based on Feature Point

2011 ◽  
Vol 128-129 ◽  
pp. 495-499
Author(s):  
Jian Hua Li ◽  
Ping Li ◽  
Xiao Dan Li ◽  
Yi Wen Wang
Keyword(s):  
Least Square Method ◽  
Detection Algorithm ◽  
Least Square ◽  
Detection Methods ◽  
Automatic Identification ◽  
Feature Points ◽  
Skew Angle ◽  
Bar Code ◽  
Character Code ◽  
The Common

The automatic identification of 2D (two dimensional) bar code PDF417 is very sensitive to skew angle, but, the common skew angle detection methods have shortcomings such as weak performance in time complexity. In this paper, based on the properties of PDF417 character code and the extraction of feature points, we get skew angle of PDF417 bar code image using the least square method. Experiments show that this algorithm has virtue of less computation and high accuracy.

scholarly journals Cutting Blade Measurement of an Ultrasonic Cutting Machine Using Multi-Step Detection

2019 ◽  
Vol 9 (16) ◽  
pp. 3338 ◽  
Author(s):  
Tae-Gu Kim ◽  
Sheikh Faisal Ahmad ◽  
Byoung-Ju Yun ◽  
Hyun Deok Kim
Keyword(s):  
Rotation Angle ◽  
Detection Method ◽  
Region Of Interest ◽  
Least Square Method ◽  
Thickness Measurement ◽  
Least Square ◽  
Step Detection ◽  
Cutting Machine ◽  
Otsu Method ◽  
Binarization Method

An algorithm for measurement of the cutting blade of the ultrasonic vibration cutting machine used in an automation machine is proposed in this paper. The proposed algorithm, which is based upon a multi-step detection method, is developed for the accurate measurement of the cutting blade by exactly determining its rotation angle, length, and thickness. Instead of the commonly used Otsu method, we propose a new curvature-based adaptive binarization method, which provides more accurate details about the dimensions of the cutting blade. A region of interest containing the cutting blade from the acquired image is first extracted in the multi-step detection method, which is further processed to remove the noise, which increases the measurement reliability. An important feature of the proposed process is the restoration of the cutting blade’s tip data, which used to be lost during the fine noise-filtering process. The rotation angle and length are measured using the minimum rotated rectangle while the line fitting based upon the least square method is applied to increase the reliability of the thickness measurement. Experimental results validate the superiority of the proposed method over the conventional Otsu method.

Direct Assessment of Effective Renal Plasma Flow from Renoscintigraphy with a Gamma Camera and an On-Line Computer

1981 ◽  
Vol 20 (06) ◽  
pp. 274-278
Author(s):  
J. Liniecki ◽  
J. Bialobrzeski ◽  
Ewa Mlodkowska ◽  
M. J. Surma
Keyword(s):  
Count Rate ◽  
Renal Plasma Flow ◽  
Early Period ◽  
Least Square Method ◽  
Least Square ◽  
Uptake Coefficient ◽  
Positive Linear Correlation ◽  
On Line ◽  
Best Fit ◽  
Plasma Activity

A concept of a kidney uptake coefficient (UC) of 131I-o-hippurate was developed by analogy from the corresponding kidney clearance of blood plasma in the early period after injection of the hippurate. The UC for each kidney was defined as the count-rate over its ROI at a time shorter than the peak in the renoscintigraphic curve divided by the integral of the count-rate curve over the "blood"-ROI. A procedure for normalization of both curves against each other was also developed. The total kidney clearance of the hippurate was determined from the function of plasma activity concentration vs. time after a single injection; the determinations were made at 5, 10, 15, 20, 30, 45, 60, 75 and 90 min after intravenous administration of 131I-o-hippurate and the best-fit curve was obtained by means of the least-square method. When the UC was related to the absolute value of the clearance a positive linear correlation was found (r = 0.922, ρ > 0.99). Using this regression equation the clearance could be estimated in reverse from the uptake coefficient calculated solely on the basis of the renoscintigraphic curves without blood sampling. The errors of the estimate are compatible with the requirement of a fast appraisal of renal function for purposes of clinical diagknosis.

PENGARUH KNOWLEDGE MANAGEMENT, KOMPETENSI, MOTIVASI TERHADAP KINERJA KARYAWAN

2015 ◽  
Vol 5 (2) ◽  
pp. 1
Author(s):  
Miftahol Arifin
Keyword(s):  
Knowledge Management ◽  
Linear Regression ◽  
Significant Influence ◽  
Employee Performance ◽  
Least Square Method ◽  
Least Square ◽  
Analysis Tool ◽  
Ordinary Least Square ◽  
Competence Motivation ◽  
Performance Analyze

The purpose of this research is to analyze the influence of knowledge management on employee performance, analyze the effect of competence on employee performance, analyze the influence of motivation on employee performance). In this study, samples taken are structural employees PT.centris Kingdom Taxi Yogyakarta. The analysis tool in this study using multiple linear regression with Ordinary Least Square method (OLS). The conclusion of this study showed that the variables of knowledge management has a significant influence on employee performance, competence variables have an influence on employee performance, motivation variables have an influence on employee performance, The analysis showed that the variables of knowledge management, competence, motivation on employee performance.Keywords: knowledge management, competence, motivation, employee performance.

Peristaltic Carreau-Yasuda nanofluid flow and mixed heat transfer analysis in an asymmetric vertical and tapered wavy wall channel

2020 ◽  
Vol 1 (1) ◽  
pp. 128-140 ◽  
Author(s):  
Mohammad Hatami ◽  
◽  
D Jing ◽  
Keyword(s):  
Heat Transfer ◽  
Least Square Method ◽  
Weissenberg Number ◽  
Least Square ◽  
Heat Transfer Analysis ◽  
Phase Method ◽  
Nanofluid Flow ◽  
Two Phase ◽  
Nanoparticles Concentration ◽  
The Right

In this study, two-phase asymmetric peristaltic Carreau-Yasuda nanofluid flow in a vertical and tapered wavy channel is demonstrated and the mixed heat transfer analysis is considered for it. For the modeling, two-phase method is considered to be able to study the nanoparticles concentration as a separate phase. Also it is assumed that peristaltic waves travel along X-axis at a constant speed, c. Furthermore, constant temperatures and constant nanoparticle concentrations are considered for both, left and right walls. This study aims at an analytical solution of the problem by means of least square method (LSM) using the Maple 15.0 mathematical software. Numerical outcomes will be compared. Finally, the effects of most important parameters (Weissenberg number, Prandtl number, Brownian motion parameter, thermophoresis parameter, local temperature and nanoparticle Grashof numbers) on the velocities, temperature and nanoparticles concentration functions are presented. As an important outcome, on the left side of the channel, increasing the Grashof numbers leads to a reduction in velocity profiles, while on the right side, it is the other way around.

Fast noise removal algorithm for HDR image based on least square method

2009 ◽  
Vol 29 (4) ◽  
pp. 994-996
Author(s):  
De-quan SUN ◽  
Jun ZHANG ◽  
Xiao-feng LI ◽  
Hui LI
Keyword(s):  
Least Square Method ◽  
Noise Removal ◽  
Least Square ◽  
Hdr Image
Sign in / Sign up

Export Citation Format

Share Document