High frequency noise removal from ECG using moving average filters

2016 ◽  
Author(s):  
Vishakha Pandey ◽  
V. K. Giri
Keyword(s):  
High Frequency ◽  
Moving Average ◽  
Noise Removal ◽  
Frequency Noise ◽  
High Frequency Noise

scholarly journals Reconfigurable Architectures with High-Frequency Noise Suppression for Wearable ECG Devices

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
V. Joseph Michael Jerard ◽  
M. Thilagaraj ◽  
K. Pandiaraj ◽  
M. Easwaran ◽  
Petchinathan Govindan ◽  
...  
Keyword(s):  
High Frequency ◽  
Critical Path ◽  
Moving Average ◽  
Well Being ◽  
Frequency Noise ◽  
Ecg Signal ◽  
Noise Power ◽  
High Frequency Noise ◽  
Clock Speed ◽  
Look Ahead

Recent advances in electronics and microelectronics have aided the development of low-cost devices that are widely used as well-being or preventive monitoring devices by many people. Remote health monitoring, which includes wearable sensors, actuators, and modern communication and information systems, offers effective programs that allow people to live peacefully in their own homes while also being protected in some way. High-frequency noise, power-line interface, and baseline drift are prevalent during the data-acquisition system of an ECG signal, and they can limit signal understanding. They (noises) must be isolated in order to provide an appropriate diagnostic of the patient. When removing high-frequency components (noise) from an ECG signal with an FIR filter, the critical path delay increases considerably as the filter's duration increases. To reduce high-frequency noise, simple moving average filters with pipelining and look-ahead transformation techniques are extensively used in this study. With the use of pipelining and look-ahead techniques, the only objective is to increase the clock speed of the designs. The moving average filters (conventional and proposed) were created on an Altera Cyclone IV FPGA EP4CE115F29C7 chip using the Quartus II software v13.1 tool. Finally, performance metrics such logic elements, clock speed, and power consumption were compared and studied thoroughly. The recursive pipelined 8-tap MA filter with look-ahead approach outperforms the other designs (685.48 MHz) in this investigation.

Case study: Simulation and control of high frequency noise for commercial vehicle cab considering leak

2019 ◽  
Vol 67 (4) ◽  
pp. 315-329
Author(s):  
Rongjiang Tang ◽  
Zhe Tong ◽  
Weiguang Zheng ◽  
Shenfang Li ◽  
Li Huang
Keyword(s):  
High Frequency ◽  
Commercial Vehicle ◽  
Frequency Noise ◽  
High Frequency Noise ◽  
Simulation And Control ◽  
And Control

Aerodynamic noise from an asymmetric airfoil with perforated extension plates at the trailing edge

2020 ◽  
pp. 1475472X2097838
Author(s):  
CK Sumesh ◽  
TJS Jothi
Keyword(s):  
High Frequency ◽  
Sound Pressure ◽  
Pore Diameter ◽  
Low Frequency ◽  
Aerodynamic Noise ◽  
Frequency Noise ◽  
Low Frequency Noise ◽  
Trailing Edge ◽  
High Frequency Noise ◽  
Displacement Thickness

This paper investigates the noise emissions from NACA 6412 asymmetric airfoil with different perforated extension plates at the trailing edge. The length of the extension plate is 10 mm, and the pore diameters ( D) considered for the study are in the range of 0.689 to 1.665 mm. The experiments are carried out in the flow velocity ( U∞) range of 20 to 45 m/s, and geometric angles of attack ( αg) values of −10° to +10°. Perforated extensions have an overwhelming response in reducing the low frequency noise (<1.5 kHz), and a reduction of up to 6 dB is observed with an increase in the pore diameter. Contrastingly, the higher frequency noise (>4 kHz) is observed to increase with an increase in the pore diameter. The dominant reduction in the low frequency noise for perforated model airfoils is within the Strouhal number (based on the displacement thickness) of 0.11. The overall sound pressure levels of perforated model airfoils are observed to reduce by a maximum of 2 dB compared to the base airfoil. Finally, by varying the geometric angle of attack from −10° to +10°, the lower frequency noise is seen to increase, while the high frequency noise is observed to decrease.

Bayesian deconvolution of gamma‐ray logs

Geophysics ◽  
1987 ◽  
Vol 52 (11) ◽  
pp. 1535-1546 ◽  
Author(s):  
Ping Sheng ◽  
Benjamin White ◽  
Balan Nair ◽  
Sandra Kerford
Keyword(s):  
High Frequency ◽  
Gamma Ray ◽  
Simulated Data ◽  
Field Measurements ◽  
Bayesian Optimization ◽  
Frequency Noise ◽  
High Frequency Noise ◽  
Data Application ◽  
Gamma Ray Detector ◽  
Gamma Ray Log

The spatial resolution of gamma‐ray logs is defined by the length 𝓁 of the gamma‐ray detector. To resolve thin beds whose thickness is less than 𝓁, it is generally desirable to deconvolve the data to reduce the averaging effect of the detector. However, inherent in the deconvolution operation is an amplification of high‐frequency noise, which can be a detriment to the intended goal of increased resolution. We propose a Bayesian statistical approach to gamma‐ray log deconvolution which is based on optimization of a probability function which takes into account the statistics of gamma‐ray log measurements as well as the empirical information derived from the data. Application of this method to simulated data and to field measurements shows that it is effective in suppressing high‐frequency noise encountered in the deconvolution of gamma‐ray logs. In particular, a comparison with the least‐squares deconvolution approach indicates that the incorporation of physical and statistical information in the Bayesian optimization process results in optimal filtering of the deconvolved results.

High frequency noise of MOSFETs. II. Experiments

1998 ◽  
Vol 42 (11) ◽  
pp. 2083-2092 ◽  
Author(s):  
C.H. Chen ◽  
M.J. Deen ◽  
Z.X. Yan ◽  
M. Schroter ◽  
C Enz
Keyword(s):  
High Frequency ◽  
Frequency Noise ◽  
High Frequency Noise
Sign in / Sign up

Export Citation Format

Share Document