In-situ test study on hydraulic fills ground improvement by high vacuum compact method

2011 ◽  
Author(s):  
Qingzhi Yan ◽  
Yanhua Wang ◽  
Liqun Jiang
Keyword(s):  
Ground Improvement ◽  
High Vacuum ◽  
In Situ Test ◽  
Test Study ◽  
Hydraulic Fills

Structure of Palladium Single-Crystal Films Prepared by Flash Evaporation onto (001) NaCl Substrates

1970 ◽  
Vol 28 ◽  
pp. 456-457
Author(s):  
L. E. Murr ◽  
G. Wong
Keyword(s):  
Single Crystal ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
High Rate ◽  
Flash Evaporation ◽  
Optimum Load ◽  
Single Crystal Films ◽  
Crystal Films ◽  
A Current

Palladium single-crystal films have been prepared by Matthews in ultra-high vacuum by evaporation onto (001) NaCl substrates cleaved in-situ, and maintained at ∼ 350° C. Murr has also produced large-grained and single-crystal Pd films by high-rate evaporation onto (001) NaCl air-cleaved substrates at 350°C. In the present work, very large (∼ 3cm2), continuous single-crystal films of Pd have been prepared by flash evaporation onto air-cleaved (001) NaCl substrates at temperatures at or below 250°C. Evaporation rates estimated to be ≧ 2000 Å/sec, were obtained by effectively short-circuiting 1 mil tungsten evaporation boats in a self-regulating system which maintained an optimum load current of approximately 90 amperes; corresponding to a current density through the boat of ∼ 4 × 104 amperes/cm2.

Hetero-Epitaxy of Group Va Metals on Sapphire

1972 ◽  
Vol 30 ◽  
pp. 492-493
Author(s):  
J. E. O'Neal ◽  
J. J. Bellina ◽  
B. B. Rath
Keyword(s):  
Thermal Contact ◽  
High Vacuum ◽  
Electron Beam Evaporation ◽  
Ultra High Vacuum ◽  
Backing Plate ◽  
Sapphire Substrates ◽  
Deposition Parameters ◽  
Polishing Damage ◽  
Reflection Electron Diffraction

Thin films of the bcc metals vanadium, niobium and tantalum were epitaxially grown on (0001) and sapphire substrates. Prior to deposition, the mechanical polishing damage on the substrates was removed by an in-situ etch. The metal films were deposited by electron-beam evaporation in ultra-high vacuum. The substrates were heated by thermal contact with an electron-bombarded backing plate. The deposition parameters are summarized in Table 1.The films were replicated and examined by electron microscopy and their crystallographic orientation and texture were determined by reflection electron diffraction. Verneuil-grown and Czochralskigrown sapphire substrates of both orientations were employed for each evaporation. The orientation of the metal deposit was not affected by either increasing the density of sub-grain boundaries by about a factor of ten or decreasing the deposition rate by a factor of two. The results on growth epitaxy are summarized in Tables 2 and 3.

An in situ and ex situ TEM study of the formation of thin cobalt silicide films by molecular beam epitaxy on the silicon (100) surface

1988 ◽  
Vol 46 ◽  
pp. 884-885
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove ◽  
R. T. Tung
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Defect Density ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Metal Base ◽  
In Situ Experiments ◽  
Potential Applications

The cobalt disilicide/silicon system has potential applications as a metal-base and as a permeable-base transistor. Although thin, low defect density, films of CoSi2 on Si(111) have been successfully grown, there are reasons to believe that Si(100)/CoSi2 may be better suited to the transmission of electrons at the silicon/silicide interface than Si(111)/CoSi2. A TEM study of the formation of CoSi2 on Si(100) is therefore being conducted. We have previously reported TEM observations on Si(111)/CoSi2 grown both in situ, in an ultra high vacuum (UHV) TEM and ex situ, in a conventional Molecular Beam Epitaxy system.The procedures used for the MBE growth have been described elsewhere. In situ experiments were performed in a JEOL 200CX electron microscope, extensively modified to give a vacuum of better than 10-9 T in the specimen region and the capacity to do in situ sample heating and deposition. Cobalt was deposited onto clean Si(100) samples by thermal evaporation from cobalt-coated Ta filaments.

Nucleation and initial growth of Pd2Si crystals on Si(111)

1993 ◽  
Vol 51 ◽  
pp. 844-845
Author(s):  
Xianghong Tong ◽  
Oliver Pohland ◽  
J. Murray Gibson
Keyword(s):  
High Vacuum ◽  
Dark Field ◽  
Ultra High Vacuum ◽  
Initial Growth ◽  
Surface And Interface ◽  
Dark Field Imaging ◽  
Transmission Electron ◽  
Initial Stage ◽  
Effect Of Surface

The nucleation and initial stage of Pd2Si crystals on Si(111) surface is studied in situ using an Ultra-High Vacuum (UHV) Transmission Electron Microscope (TEM). A modified JEOL 200CX TEM is used for the study. The Si(111) sample is prepared by chemical thinning and is cleaned inside the UHV chamber with base pressure of 1x10−9 τ. A Pd film of 20 Å thick is deposited on to the Si(111) sample in situ using a built-in mini evaporator. This room temperature deposited Pd film is thermally annealed subsequently to form Pd2Si crystals. Surface sensitive dark field imaging is used for the study to reveal the effect of surface and interface steps.The initial growth of the Pd2Si has three stages: nucleation, growth of the nuclei and coalescence of the nuclei. Our experiments shows that the nucleation of the Pd2Si crystal occurs randomly and almost instantaneously on the terraces upon thermal annealing or electron irradiation.

Transmission Electron Microscopy of Epitaxial silicides grown by ultra high vacuum deposition

1989 ◽  
Vol 47 ◽  
pp. 462-463
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Diffraction ◽  
High Vacuum ◽  
High Energy ◽  
Energy Electron ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Transmission Electron

The silicides CoSi2 and NiSi2 are both metallic with the fee flourite structure and lattice constants which are close to silicon (1.2% and 0.6% smaller at room temperature respectively) Consequently epitaxial cobalt and nickel disilicide can be grown on silicon. If these layers are formed by ultra high vacuum (UHV) deposition (also known as molecular beam epitaxy or MBE) their thickness can be controlled to within a few monolayers. Such ultrathin metal/silicon systems have many potential applications: for example electronic devices based on ballistic transport. They also provide a model system to study the properties of heterointerfaces. In this work we will discuss results obtained using in situ and ex situ transmission electron microscopy (TEM).In situ TEM is suited to the study of MBE growth for several reasons. It offers high spatial resolution and the ability to penetrate many monolayers of material. This is in contrast to the techniques which are usually employed for in situ measurements in MBE, for example low energy electron diffraction (LEED) and reflection high energy electron diffraction (RHEED), which are both sensitive to only a few monolayers at the surface.

Sign in / Sign up

Export Citation Format

Share Document