Finite element analysis of stress distribution in immediately loaded dental implant

2012 ◽  
Author(s):  
Babak Bahrami ◽  
Farzan Ghalichi ◽  
Behnam Mirzakouchaki ◽  
Mohammed N. Ashtiani ◽  
Arsalan Marghoub
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Dental Implant ◽  
Element Analysis

scholarly journals Effect of Offset Implant Placement on the Stress Distribution Around a Dental Implant: A Three-Dimensional Finite Element Analysis

2015 ◽  
Vol 41 (6) ◽  
pp. 646-651 ◽  
Author(s):  
Hakimeh Siadat ◽  
Shervin Hashemzadeh ◽  
Allahyar Geramy ◽  
Seyed Hossein Bassir ◽  
Marzieh Alikhasi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Distribution ◽  
Dental Implant ◽  
Three Dimensional ◽  
Element Analysis ◽  
3D Finite Element ◽  
Implant Placement ◽  
Mandibular Molar

There are some anatomical restrictions in which implants are not possible to be inserted in their conventional configuration. Offset placement of implants in relation to the prosthetic unit could be a treatment solution. The aim of this study was to evaluate the effect of the offset placement of implant-supported prosthesis on the stress distribution around a dental implant using 3D finite element analysis. 3D finite element models of implant placement in the position of a mandibular molar with 4 configurations (0, 0.5, 1, 1.5 mm offset) were created in order to investigate resultant stress/strain distribution. A vertical load of 100 N was applied on the center of the crown of the models. The least stress in peri-implant tissue was found in in-line configuration (0 mm offset). Stress concentration in the peri-implant tissue increased by increasing the amount of offset placement. Maximum stress concentration in all models was detected at the neck of the implant. It can be concluded that the offset placement of a single dental implant does not offer biomechanical advantages regarding reducing stress concentration over the in-line implant configuration. It is suggested that the amount of offset should be as minimum as possible.

scholarly journals Comparative Analysis of Stress and Deformation between One-Fenced and Three-Fenced Dental Implants Using Finite Element Analysis

2021 ◽  
Vol 10 (17) ◽  
pp. 3986
Author(s):  
Chia-Hsuan Lee ◽  
Arvind Mukundan ◽  
Szu-Chien Chang ◽  
Yin-Lai Wang ◽  
Shu-Hao Lu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Comparative Analysis ◽  
Stress Distribution ◽  
Dental Implant ◽  
Maximum Stress ◽  
Vertical Force ◽  
Element Analysis ◽  
Different Types ◽  
Stress And Deformation

Finite element analysis (FEA) has always been an important tool in studying the influences of stress and deformation due to various loads on implants to the surrounding jaws. This study assessed the influence of two different types of dental implant model on stress dissipation in adjoining jaws and on the implant itself by utilizing FEA. This analysis aimed to examine the effects of increasing the number of fences along the implant and to compare the resulting stress distribution and deformation with surrounding bones. When a vertical force of 100 N was applied, the largest displacements found in the three-fenced and single-fenced models were 1.7469 and 2.5267, respectively, showing a drop of 30.8623%. The maximum stress found in the three-fenced and one-fenced models was 13.518 and 22.365 MPa, respectively, showing a drop of 39.557%. Moreover, when an oblique force at 35° was applied, a significant increase in deformation and stress was observed. However, the three-fenced model still had less stress and deformation compared with the single-fenced model. The FEA results suggested that as the number of fences increases, the stress dissipation increases, whereas deformation decreases considerably.

scholarly journals Effect of design parameters of dental implant on stress distribution: a finite element analysis

2020 ◽  
Vol 9 (3) ◽  
pp. 621
Author(s):  
Pooyan Rahmanivahid ◽  
Milad Heidari
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Dental Implants ◽  
Dental Implant ◽  
Cancellous Bone ◽  
Design Parameters ◽  
Element Analysis ◽  
Small Surface ◽  
Design Factors

Nowadays, root osseointegrated dental implants are used widely in dentistry mainly for replacement of the single missing tooth. The success rate of osseointegrated dental implants depends on different factors such as bone conditions; surgery insertion technique, loading history, and biomechanical interaction between jawbone and implant surface. In recent years, many studies have investigated design factors using finite element analysis with a concentration on major parameters such as diameter, pitch, and implant outlines in the distribution of stress in the bone-implant interface. There is still a need to understand the relationship and interaction of design factors individually with stress distribution to optimize implant structure. Therefore, the present study introduced a new dental implant and investigated the effect of design parameters on stress distribution. The finite element modeling was developed to facilitate the study with a comparison of design parameters. Boundary and loading conditions were implemented to simulate the natural situation of occlusal forces. Based on results, V-shape threads with maximum apex angle caused a high rate of micro-motion and high possibility of bone fracture. Low Von-Mises stress was associated with low bone growth stimulation. Besides, small fin threads did not integrate with cancellous bone and consequently lower stress accommodation. V-5 fin had no extraordinary performance in cancellous bone. Small surface areas of fins did not integrate with the surrounding bone and high-stress concentration occurred at the tail. These fins are recommended as threads replacement. It was concluded that the implant structure had less influence on stress distribution under horizontal loading.  

scholarly journals Finite Element Analysis of a New Dental Implant Design Optimized for the Desirable Stress Distribution in the Surrounding Bone Region

Prosthesis ◽  
2020 ◽  
Vol 2 (3) ◽  
pp. 225-236 ◽  
Author(s):  
Luigi Paracchini ◽  
Christian Barbieri ◽  
Mattia Redaelli ◽  
Domenico Di Croce ◽  
Corrado Vincenzi ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Cortical Bone ◽  
Dental Implant ◽  
Neck Region ◽  
Implant Design ◽  
Three Dimensional Model ◽  
Element Analysis ◽  
Surrounding Bone

Dental implant macro- and micro-shape should be designed to maximize the delivery of optimal favorable stresses in the surrounding bone region. The present study aimed to evaluate the stress distribution in cortical and cancellous bone surrounding two models of dental implants with the same diameter and length (4.0 × 11 mm) and different implant/neck design and thread patterns. Sample A was a standard cylindric implant with cylindric neck and V-shaped threads, and sample B was a new conical implant with reverse conical neck and with “nest shape” thread design, optimized for the favorable stress distribution in the peri-implant marginal bone region. Materials and methods: The three-dimensional model was composed of trabecular and cortical bone corresponding to the first premolar mandibular region. The response to static forces on the samples A and B were compared by finite element analysis (FEA) using an axial load of 100 N and an oblique load of 223.6 N (resulting from a vertical load of 100 N and a horizontal load of 200 N). Results: Both samples provided acceptable results under loadings, but the model B implant design showed lower strain values than the model A implant design, especially in cortical bone surrounding the neck region of the implant. Conclusions: Within the limitation of the present study, analyses suggest that the new dental implant design may minimize the transfer of stress to the peri-implant cortical bone.

Effects of Custom-Made and Thread Dental Implant Systems on the Stress Distribution in Alveolar Bone: A 3-Dimensional Finite Element Analysis

2013 ◽  
Vol 475-476 ◽  
pp. 1487-1493 ◽  
Author(s):  
Xiao Zhang ◽  
Zhan Gong Xie ◽  
Wei Feng ◽  
Xian Shuai Chen ◽  
Jian Yu Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Dental Implant ◽  
Alveolar Bone ◽  
Element Analysis ◽  
Custom Made ◽  
Dimensional Finite Element ◽  
Stress And Deformation ◽  
Implant System

Aiming to investigate the effects of custom-made and thread dental implant systems on the stress distribution in alveolar bone using linear analysis of the finite element method (FEM). Two types of systems: the custom-made implant and the thread dental implant system, were studied using a three-dimensional finite element analysis (3D FEA). Comparing the parts of all systems for loading in different directions, the stress and deformation distribution in custom-made implant and alveolar bone are better than that in thread dental implant system. The analysis data definitely demonstrated the difference in stress and deformation distribution of components in different dental implant systems. Results show the custom-made implants are provided with more advantages and can be used in future experiment and clinical test.

Sign in / Sign up

Export Citation Format

Share Document