FPGA based acceleration of computational fluid flow simulation on unstructured mesh geometry

2012 ◽  
Author(s):  
Zoltan Nagy ◽  
Csaba Nemes ◽  
Antal Hiba ◽  
Andras Kiss ◽  
Arpad Csik ◽  
...  
Keyword(s):  
Fluid Flow ◽  
Unstructured Mesh ◽  
Flow Simulation ◽  
Computational Fluid Flow

scholarly journals Analysis of Fracture Roughness Control on Permeability Using SfM and Fluid Flow Simulations: Implications for Carbonate Reservoir Characterization

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-19 ◽  
Author(s):  
Miller Zambrano ◽  
Alan D. Pitts ◽  
Ali Salama ◽  
Tiziano Volatili ◽  
Maurizio Giorgioni ◽  
...  
Keyword(s):  
Fluid Flow ◽  
Reservoir Characterization ◽  
Flow Simulation ◽  
Carbonate Reservoir ◽  
Single Fracture ◽  
Parallel Plates ◽  
Surface Mapping ◽  
Navier Stokes Equation ◽  
Hydraulic Aperture ◽  
Fracture Modeling

Fluid flow through a single fracture is traditionally described by the cubic law, which is derived from the Navier-Stokes equation for the flow of an incompressible fluid between two smooth-parallel plates. Thus, the permeability of a single fracture depends only on the so-called hydraulic aperture which differs from the mechanical aperture (separation between the two fracture wall surfaces). This difference is mainly related to the roughness of the fracture walls, which has been evaluated in previous works by including a friction factor in the permeability equation or directly deriving the hydraulic aperture. However, these methodologies may lack adequate precision to provide valid results. This work presents a complete protocol for fracture surface mapping, roughness evaluation, fracture modeling, fluid flow simulation, and permeability estimation of individual fracture (open or sheared joint/pressure solution seam). The methodology includes laboratory-based high-resolution structure from motion (SfM) photogrammetry of fracture surfaces, power spectral density (PSD) surface evaluation, synthetic fracture modeling, and fluid flow simulation using the Lattice-Boltzmann method. This work evaluates the respective controls on permeability exerted by the fracture displacement (perpendicular and parallel to the fracture walls), surface roughness, and surface pair mismatch. The results may contribute to defining a more accurate equation of hydraulic aperture and permeability of single fractures, which represents a pillar for the modeling and upscaling of the hydraulic properties of a geofluid reservoir.

The Introduction of Micro Cells to Treat Pressure in Free Surface Fluid Flow Problems

1995 ◽  
Vol 117 (4) ◽  
pp. 683-690 ◽  
Author(s):  
Peter E. Raad ◽  
Shea Chen ◽  
David B. Johnson
Keyword(s):  
Fluid Flow ◽  
Free Surface ◽  
Pressure Field ◽  
Flow Simulation ◽  
New Method ◽  
Computational Domain ◽  
Critical Feature ◽  
Flow Problems ◽  
Macro Cell ◽  
Marker And Cell Method

A new method of calculating the pressure field in the simulation of two-dimensional, unsteady, incompressible, free surface fluid flow by use of a marker and cell method is presented. A critical feature of the new method is the introduction of a finer mesh of cells in addition to the regular mesh of finite volume cells. The smaller (micro) cells are used only near the free surface, while the regular (macro) cells are used throughout the computational domain. The movement of the free surface is accomplished by the use of massless surface markers, while the discrete representation of the free surface for the purpose of the application of pressure boundary conditions is accomplished by the use of micro cells. In order to exploit the advantages offered by micro cells, a new general equation governing the pressure field is derived. Micro cells also enable the identification and treatment of multiple points on the free surface in a single surface macro cell as well as of points on the free surface that are located in a macro cell that has no empty neighbors. Both of these situations are likely to occur repeatedly in a free surface fluid flow simulation, but neither situation has been explicitly taken into account in previous marker and cell methods. Numerical simulation results obtained both with and without the use of micro cells are compared with each other and with theoretical solutions to demonstrate the capabilities and validity of the new method.

A Characteristic-Featured Shock Wave Indicator for Simulating High-Speed Inviscid Flows on 3D Unstructured Mesh

2021 ◽  
Author(s):  
Yiwei Feng ◽  
Tiegang Liu ◽  
Xiaofeng He ◽  
Bin Zhang ◽  
Kun Wang
Keyword(s):  
Shock Wave ◽  
High Speed ◽  
Unstructured Mesh ◽  
High Efficiency ◽  
Flow Simulation ◽  
Attractive Alternative ◽  
Inviscid Flows ◽  
Speed Flow ◽  
Flow Compression ◽  
Shock Processing

Abstract In this work, we extend the characteristic-featured shock wave indicator based on artificial neuron training to 3D high-speed flow simulation on unstructured mesh. The extension is achieved through dimension splitting. This leads to that the proposed indicator is capable of identifying regions of flow compression in any direction. With this capability, the indicator is further developed to combine with h-adaptivity of mesh refinement to improve resolution with less computational costs. The present indicator provided an attractive alternative for constructing high-resolution, high-efficiency shock-processing method to simulate high-speed inviscid flows.

Impact of Seismic Constraints on a Stochastic Reservoir Model and Fluid Flow Simulation

2002 ◽  
pp. 53-67
Author(s):  
I. Azpiritxaga ◽  
A. Correa ◽  
E. Hernandez ◽  
A. Galli ◽  
C. Ravenne ◽  
...  
Keyword(s):  
Fluid Flow ◽  
Flow Simulation ◽  
Reservoir Model
Sign in / Sign up

Export Citation Format

Share Document