Method of Accurate Design of a Microwave Band-Pass Filter Based on Adjust of Center Frequency

2009 ◽  
Author(s):  
Li-ming Zhang ◽  
Quan-yuan Feng ◽  
Li-wen You
Keyword(s):  
Center Frequency ◽  
Band Pass Filter ◽  
Microwave Band ◽  
Pass Filter ◽  
Accurate Design ◽  
Band Pass

Envelope Analysis Based on the Combination of Morlet Wavelet and Kurtogram

2012 ◽  
Vol 490-495 ◽  
pp. 305-308
Author(s):  
Yu Liang ◽  
Yu Guo ◽  
Chuan Hui Wu ◽  
Yan Gao
Keyword(s):  
Frequency Band ◽  
Filter Banks ◽  
Morlet Wavelet ◽  
Center Frequency ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Filter Bandwidth ◽  
Envelope Analysis ◽  
Band Pass ◽  
Complex Morlet Wavelet

Envelope analysis based on the combination of complex Morlet wavelet and Kurtogram have advantages of automatic calculation of the center frequency and bandwidth of required band-pass filter. However, there are some drawbacks in the traditional algorithm, which include that the filter bandwidth is not -3dB bandwidth and the analysis frequency band covered by the filter-banks are inconsistent at different levels. A new algorithm is introduced in this paper. Through it, both optimal center frequency and bandwidth of band-pass filter in the envelop analysis can be obtained adaptively. Meanwhile, it ensures that the filters in the filter-banks are overlapped at the point of -3dB bandwidth and the consistency of frequency band that the filter-banks covered.

Reconfigurable dual-mode band-pass filter with switchable bandwidth using PIN diodes

2014 ◽  
Vol 7 (6) ◽  
pp. 655-660 ◽  
Author(s):  
Photos Vryonides ◽  
Symeon Nikolaou ◽  
Sangkil Kim ◽  
Manos M. Tentzeris
Keyword(s):  
Insertion Loss ◽  
Center Frequency ◽  
Band Pass Filter ◽  
Dual Mode ◽  
Pin Diodes ◽  
Pass Filter ◽  
Physical Size ◽  
Wireless Applications ◽  
Band Pass ◽  
Dc Bias

A reconfigurable band-pass filter with switchable bandwidth, for wireless applications is demonstrated using a dual-mode microstrip square-loop resonator. The proposed filter has been designed on Rogers RO4003C and achieves switchable bandwidth by changing the length of two tuning stubs with the implementation of two strategically placed p-i-n diodes as switching elements. The filter was designed with a center frequency of 2.4 GHz and the two distinct operation states have bandwidths, 113 MHz (4.8%) with an insertion loss of 1.2 dB and 35 MHz (1.5%) with an insertion loss of 1.5 dB. The physical size of the fabricated reconfigurable filter including the implementation of the DC bias lines is comparable to the size of a conventional filter.

Tunable Band-Pass Filters Employing Stretchable Electronic Components

2012 ◽  
Author(s):  
Geoffrey A. Slipher ◽  
Randy A. Mrozek ◽  
Justin L. Shumaker
Keyword(s):  
Center Frequency ◽  
Band Pass Filter ◽  
Electronic Components ◽  
Circuit Element ◽  
Pass Filter ◽  
Dependent Behavior ◽  
Band Pass ◽  
Spatio Temporal ◽  
Adaptive Circuit ◽  
Circuit Networks

This paper describes some of the recent results of an ongoing U.S. Army research program examining the electronic behavior of hyperelastic stretchable capacitor, resistor, and inductor networks for which the conductor material employed is stretchable. As with traditional rigid analog components, stretchable electronic components exhibit frequency-dependant behavior. Unlike their rigid counterparts, stretchable electronic components may also exhibit dramatic strain-dependent behavior. In this way stretchable circuit networks may be viewed as controllable spatio-temporal filters. Resistance, capacitance, and inductance all change to varying degrees depending on the specific set of spatio-temporal inputs. These variations may be harnessed to create an adaptive circuit element that is controllable. This paper describes the results of integrating stretchable components into a tunable band-pass filter. Center frequency, bandwidth, and gain can be varied in a controllable way by varying the capacitance or resistance of specific circuit elements by stretching them. Biaxially stretchable components are described that are subjected to equibiaxial strain-states as high as 100% area strain. We examine the influence that the type of compliant conductor has on tunable circuit properties and on control authority.

A SAW Filter of Elliptic Structure IDT

2014 ◽  
Vol 665 ◽  
pp. 623-628
Author(s):  
Dai Qiang Wang ◽  
Liang Rong Li ◽  
Yu Qing Chen ◽  
Zu Ming Yao ◽  
Hong Gong ◽  
...  
Keyword(s):  
Thin Films ◽  
Center Frequency ◽  
Band Pass Filter ◽  
Function Model ◽  
Modeling Tools ◽  
Pass Filter ◽  
Band Pass ◽  
Simulation Results ◽  
Weighting Methods ◽  
Piezoelectric Substrate

The design uses silicon-AlN thin films as the piezoelectric substrate, Use apo- dization weighting methods to optimize the design of IDT. The improved δ function model was Modeling Tools of Apodization weighted ellipse IDT structure, According to the result of simulation, we designed a layout of SAW band-pass filter and fabricated a sample of it which center frequency is 300MHz and insertion loss is 7dB, The research shows the consistency of simulation results with the experimental results.

The Design and Simulation of the Array Induction Logging Tools’ Signal Conditioning Circuit

2012 ◽  
Vol 241-244 ◽  
pp. 1010-1013
Author(s):  
Yao Hu ◽  
Hong Lu Hu ◽  
Ding Jin Huang
Keyword(s):  
Relative Error ◽  
Design Method ◽  
Center Frequency ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Band Filter ◽  
Induction Logging ◽  
Band Pass ◽  
Two Stages ◽  
Signal Conditioning Circuit

Array induction logging tools (AILT) detects the stratum conductivity based on the principle of electromagnetic induction, as a result, the signal of the amplitude using the AILT is in microvolt level. The small-signal is always drowned by noise at high-temperature and high-pressure condition. In order to collect the weak signal accurately, we propose a design method of signal modulator circuits based on the principle of differential amplifier and active band-pass filter with second band limitless gain and multi-path negative feedback. First, make the induction signal obtained from the coil two stages amplification. Then Execute two-order band-pass filter to the enlarged signal. At last, process the filtered signal by the backward circuits. Simulating the circuits by Pspice16.3, The result of simulation indicated that the gain relative error of preamplifier is less than 1% and the center frequency relative error of band filter is less than 4%. These data suggest that the relative error of the design circuits is less than routine instrument by 5%. So the Simulation verifies the feasibility of the signal modulator circuit.

Sign in / Sign up

Export Citation Format

Share Document