Analysis and comparaison of different Heat Transfer Fluids for a 1MWe Parabolic Trough Collector

2016 ◽  
Author(s):  
Ahmed Alami Merrouni ◽  
Hanane Ait Lahoussine Ouali ◽  
Mohammed Amine Moussaoui ◽  
Ahmed Mezrhab
Keyword(s):  
Heat Transfer ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Heat Transfer Fluids

scholarly journals Contribution to the Parametric Study of the Performance of A Parabolic Trough Collector

2021 ◽  
Vol 321 ◽  
pp. 02016
Author(s):  
Belkacem Bouali ◽  
Hanane-Maria Regue
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Flow Rate ◽  
Optimal Operation ◽  
Heat Transfer Fluid ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Heat Transfer Fluids ◽  
Ansys Cfx ◽  
Different Seasons

This paper presents an analysis of the performance of a parabolic trough collector (PTC) according to some key operating parameters. The effects of the secondary reflector, the length and thickness of the absorber tube (receiver tube) and the flow rate of the heat transfer fluid (HTF) are investigated. The main objective is to determine an optimal operation, which improves the performance of a traditional PTC. The target variables are the temperature at the outlet of the tube, the amount of energy collected by the HTF and the efficiency of the system. The solar flux data concern the city of LAGHOUAT located in the south of Algeria. Four days in different seasons are considered. The optical analysis of the system is performed by using the open source SolTrace code. The output of this analysis is used as a boundary condition for the CFD solver. The conjugate heat transfer and the fluid flow through the absorber tube are simulated by using ANSYS-CFX solver. Water is considered as heat transfer fluids. The obtained results show that the use of a curved secondary reflector significantly improves the performance of the traditional PTC. As the thickness of the tube increases, the heat storage in the material increases, which increases the temperature at the exit of the tube and therefore the efficiency of the system. However, the length of the tube depends on the mass flow of the HTF and vice versa. To keep the efficiency constant by choosing another length, it is necessary to choose a mass flow rate proportional to the flow rate corresponding to the initial length.

scholarly journals Investigation of energetic and exergetic performances of parabolic trough collector with using different heat transfer fluids

2019 ◽  
Vol 111 ◽  
pp. 01054 ◽  
Author(s):  
F. Mertkan Arslan ◽  
Hüseyin Günerhan
Keyword(s):  
Heat Transfer ◽  
Energy Efficiency ◽  
Molten Salt ◽  
Sodium Nitrate ◽  
Potassium Nitrate ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Working Fluids ◽  
Selective Coating ◽  
Heat Transfer Fluids

In this study energetic and exergetic performances of parabolic trough collector is theoretically investigated by using 120 l/min synthetic ‘’Dowtherm A’’ oil , 1200 l/min Air at 100 bar (10 MPa) and 150 l/min molten salt which is mixture of 60 wt% sodium nitrate (NaNO3) and 40 wt% potassium nitrate (KNO3) which are widely used as heat transfer fluids. Fluids performance comparisons were performed with the LS-2 module, which is used with vacuum in annulus and Cermet as a selective coating. LS-2 module has 7.8 m receiver length and is 39 m2 aperture area. As a result, the maximum exergy efficiency of the molten salt, synthetic oil, Air to be 41.19% at 422 °C, 40.82% at 400 °C, 40.33% at 402 °C, respectively. The maximum exergy of air is higher than other working fluids up to 310 ° C but after about 310 ° C the exergy of the molten salt is higher than the others. The molten salt has the best energy efficiency at its operating temperatures (250 °C to 550 °C) than other working fluids.

Comparative Study on Parabolic Trough Collector by using Different Heat Transfer Fluids

2019 ◽  
Vol 11 (4) ◽  
Author(s):  
Krishna Mounica ◽  
Y.V. Hanumantha Rao ◽  
Vinay Atgur ◽  
G. Manavendra ◽  
B. Srinivasa Rao
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Thermal Model ◽  
Heat Transfer Fluid ◽  
Parabolic Trough ◽  
Flow Rates ◽  
Parabolic Trough Collector ◽  
Heat Transfer Fluids ◽  
Mass Flow Rates ◽  
Simulation Results

In this paper the use of Syltherm-800 and Therminol-55 thermal oils in parabolic trough collector (PTC) is investigated with inlet temperatures of 375.35 K, 424.15 K, 470.65 K and 523.85 K and for mass flow rates of 4, 4.5 and 5 kg/sec. Analysis has been carried out using a thermal model and validated using the simulation results. Therminol-55 gives better heat transfer coefficient compared to Syltherm-800. Since Therminol-55 has higher specific heat and viscosity when compared to Syltherm-800, the use of Syltherm-800 as a heat transfer fluid in PTC is preferred. Better results are observed for temperature of 375.35 K and mass flow rate of 4 kg/sec.

scholarly journals State-of-the-art heat transfer fluids for parabolic trough collector

2020 ◽  
Vol 152 ◽  
pp. 119541 ◽  
Author(s):  
Yathin Krishna ◽  
M. Faizal ◽  
R. Saidur ◽  
K.C. Ng ◽  
Navid Aslfattahi
Keyword(s):  
Heat Transfer ◽  
State Of The Art ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Heat Transfer Fluids
Sign in / Sign up

Export Citation Format

Share Document