Fundamental investigations of eddy current losses in laminated stator cores created through the impact of manufacturing processes

2011 ◽  
Author(s):  
Erik Lamprecht ◽  
Rolf Graf
Keyword(s):  
Eddy Current ◽  
Manufacturing Processes ◽  
Eddy Current Losses ◽  
The Impact

Determination of eddy current losses and hysteresis losses in magnetic circuits of electrical machines

2020 ◽  
pp. 54-58
Author(s):  
S. M. Plotnikov
Keyword(s):  
Eddy Current ◽  
Magnetization Reversal ◽  
Eddy Currents ◽  
Technical Problem ◽  
Electrical Machines ◽  
Eddy Current Losses ◽  
Hysteresis Losses ◽  
Magnetic Circuits ◽  
Core Losses ◽  
Reversal Frequency

The division of the total core losses in the electrical steel of the magnetic circuit into two components – losses dueto hysteresis and eddy currents – is a serious technical problem, the solution of which will effectively design and construct electrical machines with magnetic circuits having low magnetic losses. In this regard, an important parameter is the exponent α, with which the frequency of magnetization reversal is included in the total losses in steel. Theoretically, this indicator can take values from 1 to 2. Most authors take α equal to 1.3, which corresponds to the special case when the eddy current losses are three times higher than the hysteresis losses. In fact, for modern electrical steels, the opposite is true. To refine the index α, an attempt was made to separate the total core losses on the basis that the hysteresis component is proportional to the first degree of the magnetization reversal frequency, and the eddy current component is proportional to the second degree. In the article, the calculation formulas of these components are obtained, containing the values of the total losses measured in idling experiments at two different frequencies, and the ratio of these frequencies. It is shown that the rational frequency ratio is within 1.2. Presented the graphs and expressions to determine the exponent α depending on the measured no-load losses and the frequency of magnetization reversal.

Losses in ac of BSCCO-2223 superconducting monofilament and multifilament tapes at power frequencies

1997 ◽  
Vol 12 (11) ◽  
pp. 3085-3089
Author(s):  
S. Mench ◽  
M. Lelovic ◽  
T. Deis ◽  
N. G. Eror ◽  
U. Balachandran ◽  
...  
Keyword(s):  
Eddy Current ◽  
Anisotropy Field ◽  
Magnetic Losses ◽  
Field Orientation ◽  
Eddy Current Losses ◽  
Order Of Magnitude

The ac magnetic losses at power frequencies (60 Hz) were investigated for mono- and multifilament Ag-sheathed (Bi, Pb)2Sr2Ca2Cu3Oy (BSCCO-2223) tapes with similar Ic values at 77 K. The multifilament sample exhibited higher losses than the monofilament under the same conditions. Loss peaks are discussed in terms of intergranular, intragranular, and eddy current losses. Because of BSCCO's anisotropy, field orientation has a large effect on the magnitude of these peaks, even at relatively small angles. Losses for fields applied parallel to the c-axis of the textured BSCCO grains are larger by over an order of magnitude than those applied perpendicular.

Free Vibration Analysis for Thin Wire of Modern Wiresaw Between Sliced Wafers in Wafer Manufacturing Processes

2000 ◽  
Author(s):  
Songbin Wei ◽  
Imin Kao
Keyword(s):  
High Speed ◽  
Free Vibration Analysis ◽  
Equation Of Motion ◽  
Manufacturing Processes ◽  
Thin Wire ◽  
Wire Vibration ◽  
The Wire ◽  
The Impact ◽  
Wafer Manufacturing ◽  
Impact Problem

Abstract In wiresaw manufacturing process where thin wire moving at high speed is pushed onto ingot to produce slices of wafer, the wire is constrained by two wafer walls as it slices into the ingot. In this paper, we investigate the vibration of such wire under the constraints of wafer walls. To address this problem, the model for wire vibration with impact to wafer walls is developed. The equation of motion is discretized using the Galerkin’s method. The principle of impulse and momentum is utilized to solve the impact problem. The results of analysis and simulation indicate that the response under a pointwise sinusoidal excitation is neither periodical nor symmetric with respect to the horizontal axis, due to the excitation from the impact. The wire vibration behavior is affected dramatically by the wafer wall constraints.

Rapid analytical method to evaluate eddy current losses in hairpin wound IM due to PWM

2021 ◽  
Author(s):  
Lino Di Leonardo ◽  
Andrea Credo ◽  
Marco Tursini ◽  
Marco Villani
Keyword(s):  
Eddy Current ◽  
Analytical Method ◽  
Eddy Current Losses
Sign in / Sign up

Export Citation Format

Share Document