High-voltage low drop output voltage regulator with output current fold-back protection in 250 nm BCD technology

2016 ◽  
Author(s):  
Vladimir A. Ryzhkov ◽  
Maksim S. Karpovich ◽  
Igor K. Surin ◽  
Vladislav Yu. Vasilyev
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
Voltage Regulator ◽  
Output Current

scholarly journals Implementation of Buck-Boost Converter as Low Voltage Stabilizer at 15 V

2019 ◽  
Vol 9 (4) ◽  
pp. 2230
Author(s):  
Suwarno Suwarno ◽  
Tole Sutikno
Keyword(s):  
Power Electronics ◽  
Wind Power ◽  
Output Voltage ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Stabilizer ◽  
Voltage Regulator ◽  
Output Current ◽  
Converter Design

<p>This paper presents the implementation of the buck-boost converter design which is a power electronics applications that can stabilize voltage, even though the input voltage changes. Regulator to stabilize the voltage using PWM pulse that triger pin 2 on XL6009. In this design of buck-boost converter is implemented using the XL6009, LM7815 and TIP2955. LM7815 as output voltage regulator at 15V with 1A output current, while TIP2955 is able to overcome output current up to 5A. When the LM7815 and TIP2955 are connected in parallel, the converter can increase the output current to 6A.. Testing is done using varied voltage sources that can be set. The results obtained from this design can be applied to PV (Photovoltaic) and WP (Wind Power), with changes in input voltage between 3-21V dc can produce output voltage 15V.</p>

scholarly journals Novel High-Efficiency High Step-Up DC–DC Converter with Soft Switching and Low Component Voltage Stress for Photovoltaic System

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1112
Author(s):  
Yu-En Wu ◽  
Jyun-Wei Wang
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
High Efficiency ◽  
Low Voltage ◽  
Leakage Inductance ◽  
Power Switch ◽  
Half Wave Voltage ◽  
Half Wave ◽  
Voltage Stress ◽  
Voltage Doubler

This study developed a novel, high-efficiency, high step-up DC–DC converter for photovoltaic (PV) systems. The converter can step-up the low output voltage of PV modules to the voltage level of the inverter and is used to feed into the grid. The converter can achieve a high step-up voltage through its architecture consisting of a three-winding coupled inductor common iron core on the low-voltage side and a half-wave voltage doubler circuit on the high-voltage side. The leakage inductance energy generated by the coupling inductor during the conversion process can be recovered by the capacitor on the low-voltage side to reduce the voltage surge on the power switch, which gives the power switch of the circuit a soft-switching effect. In addition, the half-wave voltage doubler circuit on the high-voltage side can recover the leakage inductance energy of the tertiary side and increase the output voltage. The advantages of the circuit are low loss, high efficiency, high conversion ratio, and low component voltage stress. Finally, a 500-W high step-up converter was experimentally tested to verify the feasibility and practicability of the proposed architecture. The results revealed that the highest efficiency of the circuit is 98%.

DEVELOPMENT OF CONSTRUCTION OF THREE-INPUT GENERATING INSTALLATIONS ON BASED OF RENEWABLE ENERGY SOURCES

2018 ◽  
Author(s):  
Я.М. КАШИН ◽  
Л.Е. КОПЕЛЕВИЧ ◽  
А.В. САМОРОДОВ ◽  
Ч. ПЭН
Keyword(s):  
Renewable Energy ◽  
Kinetic Energy ◽  
Total Energy ◽  
Thermal Energy ◽  
Output Voltage ◽  
Renewable Energy Sources ◽  
Electrical Energy ◽  
Energy Sources ◽  
Voltage Regulator ◽  
The Sun

Описаны конструктивные особенности трехвходовой аксиальной генераторной установки (ТАГУ), преобразующей кинетическую энергию ветра и световую энергию солнца и суммирующей механическую, световую и тепловую энергию с одновременным преобразованием полученной суммарной энергии в электрическую. Показаны преимущества ТАГУ перед двухвходовыми генераторными установками. Дополнительное включение стабилизатора напряжения в схему ТАГУ позволило расширить область применения стабилизированной трехвходовой аксиальной генераторной установки за счет стабилизации ее выходного напряжения. The design features of the three-input axial generating installation (TAGI), which converts the kinetic energy of wind and light energy of the sun and sums the mechanical, light and thermal energy with the simultaneous conversion of the total energy into electrical energy, are described. The benefits of TAGI in front of the two-input generating installation shown. The additional introduction of a voltage regulator into the TAGI scheme allowed to expand the scope of the stabilized three-input axial generating installation by stabilizing its output voltage.

A Nonisolated DC–DC Boost Converter With High Voltage Gain and Balanced Output Voltage

2014 ◽  
Vol 61 (12) ◽  
pp. 6739-6746 ◽  
Author(s):  
George Cajazeiras Silveira ◽  
Fernando Lessa Tofoli ◽  
Luiz Daniel Santos Bezerra ◽  
Rene Pastor Torrico-Bascope
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
High Voltage Gain

scholarly journals Non-conventional Cascade Multilevel Inverter with Lower Number of Switches by Using Multilevel PWM

2021 ◽  
Vol 17 (1) ◽  
pp. 1-13
Author(s):  
Adala Abdali ◽  
Ali Abdulabbas ◽  
Habeeb Nekad
Keyword(s):  
High Voltage ◽  
High Power ◽  
Power Loss ◽  
Output Voltage ◽  
Lower Number ◽  
Multilevel Inverter ◽  
Three Phase ◽  
Multi Level ◽  
Simulation Results ◽  
Circuit Configuration

The multilevel inverter is attracting the specialist in medium and high voltage applications, among its types, the cascade H bridge Multi-Level Inverter (MLI), commonly used for high power and high voltage applications. The main advantage of the conventional cascade (MLI) is generated a large number of output voltage levels but it demands a large number of components that produce complexity in the control circuit, and high cost. Along these lines, this paper presents a brief about the non-conventional cascade multilevel topologies that can produce a high number of output voltage levels with the least components. The non-conventional cascade (MLI) in this paper was built to reduce the number of switches, simplify the circuit configuration, uncomplicated control, and minimize the system cost. Besides, it reduces THD and increases efficiency. Two topologies of non-conventional cascade MLI three phase, the Nine level and Seventeen level are presented. The PWM technique is used to control the switches. The simulation results show a better performance for both topologies. THD, the power loss and the efficiency of the two topologies are calculated and drawn to the different values of the Modulation index (ma).

Sign in / Sign up

Export Citation Format

Share Document