Online Aging Parameter Extraction with Induced Voltage $v_{\text{eE}}$ between Kelvin and Power Emitter in Turn-off Progress for IGBT Modules

2018 ◽  
Author(s):  
Renju Zheng ◽  
Haoge Xu ◽  
Chengmin Li ◽  
Wuhua Li ◽  
Xiangning He ◽  
...  
Keyword(s):  
Parameter Extraction ◽  
Induced Voltage ◽  
Igbt Modules ◽  
Aging Parameter

Analysis and Design of 3.3 kV IGBT Based Three-Level DC/DC Converter with High-Frequency Isolation and Current Doubler Rectifier

2009 ◽  
Vol 25 (25) ◽  
pp. 103-108
Author(s):  
Dmitri Vinnikov ◽  
Tanel Jalakas ◽  
Indrek Roasto
Keyword(s):  
High Voltage ◽  
High Frequency ◽  
Power Converter ◽  
Rolling Stock ◽  
Analysis And Design ◽  
Auxiliary Power ◽  
Igbt Modules ◽  
Isolation Transformer ◽  
New Generation ◽  
Generation Power

Analysis and Design of 3.3 kV IGBT Based Three-Level DC/DC Converter with High-Frequency Isolation and Current Doubler RectifierThe paper presents the findings of a R&D project connected to the development of auxiliary power supply (APS) for the high-voltage DC-fed rolling stock applications. The aim was to design a new-generation power converter utilizing high-voltage IGBT modules, which can outpace the predecessors in terms of power density, i.e. to provide more power for smaller volumetric space. The topology proposed is 3.3 kV IGBT-based three-level neutral point clamped (NPC) half-bridge with high-frequency isolation transformer and current doubler rectifier that fulfils all the targets imposed by the designers. Despite an increased component count the proposed converter is very simple in design and operation. The paper provides an overview of the design with several recommendations and guidelines. Moreover, the simulation and experimental results are discussed and the performance evaluation of the proposed converter is presented.

Laser Based Analysis on Analog Circuits with Feedback Loops and a Case Study

2006 ◽  
Author(s):  
Fubin Zhang ◽  
David Maxwell
Keyword(s):  
Success Rate ◽  
High Resistance ◽  
Analog Circuits ◽  
Analog Circuit ◽  
Feedback Loops ◽  
Induced Voltage ◽  
Analog Device ◽  
Analog Ic ◽  
Successful Isolation

Abstract Based on the understanding of laser based techniques’ physics theory and the topology/structure of analog circuit systems with feedback loops, the propagation of laser induced voltage/current alteration inside the analog IC is evaluated. A setup connection scheme is proposed to monitor this voltage/current alteration to achieve a better success rate in finding the fail site or defect. Finally, a case of successful isolation of a high resistance via on an analog device is presented.

Bituminous Insulations Durability of Underground Metallic Pipelines I Field investigations

2017 ◽  
Vol 68 (3) ◽  
pp. 581-585 ◽  
Author(s):  
Gabriela Oprina ◽  
Ladislau Radermacher ◽  
Daniel Lingvay ◽  
Dorian Marin ◽  
Andreea Voina ◽  
...  
Keyword(s):  
Cathode Current Density ◽  
Induced Voltage ◽  
Cathodic Current ◽  
Field Investigations ◽  
Operation Period ◽  
Cathode Current ◽  
Protection Potential ◽  
Cathodic Protection System ◽  
Corrosion State ◽  
Good Agreement

The corrosion state of an underground metallic pipeline of �161 mm and 565 m length was assessed by specific electrical and electrochemical measurements. The investigated pipe, buried in 1997, was protected against corrosion by successive layers of bituminous material with a total thickness of 1 to 1.2 mm. The pipeline crosses three electrified railway lines (50 Hz - 28 kV), and then its route is approximately parallel to these lines; thus, the induced AC voltages between line and ground were calculated obtaining values between 4.05 and 7.1 Vrms, in good agreement with the values measured in the accessible points. The measurements regarding the insulation capacity against corrosion of the bituminous insulation, performed at one month and after 19 years of burial, showed an increase of the average cathode current density needed for obtaining the protection potential in the range �1.00 � �1.28 VCu/CuSO4 of approx. three times (from 6.65 up to 19.96 mA/m2), in good agreement with the evolution of the insulation resistance measured between the steel pipe (having a contact area with the ground of 270.5 m2) and a ground socket of 4 W, which decreased from 995 to 315 kW. Following the analysis and processing of the field collected data, it is considered that, by implementing a cheap cathodic protection system (without cathodic current power supply), based on the rectification of the AC induced voltage, the safe operation period of the investigated pipeline may be extended by at least 50 years.

scholarly journals Device Parameter Extraction for Loss Analysis of Silicon Solar Cells Based on Intelligent Model Fitting

2018 ◽  
Vol 150 ◽  
pp. 21-27 ◽  
Author(s):  
Jian Wei Ho ◽  
Johnson Wong ◽  
Percis Teena Christopher Subhodayam ◽  
Kwan Bum Choi ◽  
Divya Ananthanarayanan ◽  
...  
Keyword(s):  
Solar Cells ◽  
Model Fitting ◽  
Parameter Extraction ◽  
Silicon Solar Cells ◽  
Loss Analysis ◽  
Device Parameter ◽  
Intelligent Model
Sign in / Sign up

Export Citation Format

Share Document