Design considerations for implant — On-body UWB communication for medical applications

CONATEL 2011 ◽  
2011 ◽  
Author(s):  
Alex Cartagena Gordillo ◽  
Kui Zhou
Keyword(s):  
Medical Applications ◽  
Design Considerations ◽  
Uwb Communication

Design Considerations for Positron Transmission Tomograph Used for Non-Medical Applications

1984 ◽  
Vol 31 (1) ◽  
pp. 543-547 ◽  
Author(s):  
Hannu H. Heusala ◽  
Jari P. Silaste ◽  
Risto A. Myllyla
Keyword(s):  
Medical Applications ◽  
Design Considerations

Morphological behavior of compatibilized ternary blends prepared by mechanical mixing

1993 ◽  
Vol 51 ◽  
pp. 1200-1201
Author(s):  
S.D. Smith ◽  
R.J. Spontak ◽  
D.H. Melik ◽  
S.M. Buehler ◽  
K.M. Kerr ◽  
...  
Keyword(s):  
Interfacial Adhesion ◽  
Diblock Copolymers ◽  
Ternary Blends ◽  
Mechanical Mixing ◽  
Design Considerations ◽  
Covalently Bonded ◽  
Homopolymer Blends ◽  
Emulsifying Agent ◽  
Surface Active ◽  
Low Entropy

When blended together, homopolymers A and B will normally macrophase-separate into relatively large (≫1 μm) A-rich and B-rich phases, between which exists poor interfacial adhesion, due to a low entropy of mixing. The size scale of phase separation in such a blend can be reduced, and the extent of interfacial A-B contact and entanglement enhanced, via addition of an emulsifying agent such as an AB diblock copolymer. Diblock copolymers consist of a long sequence of A monomers covalently bonded to a long sequence of B monomers. These materials are surface-active and decrease interfacial tension between immiscible phases much in the same way as do small-molecule surfactants. Previous studies have clearly demonstrated the utility of block copolymers in compatibilizing homopolymer blends and enhancing blend properties such as fracture toughness. It is now recognized that optimization of emulsified ternary blends relies upon design considerations such as sufficient block penetration into a macrophase (to avoid block slip) and prevention of a copolymer multilayer at the A-B interface (to avoid intralayer failure).

Theoretical And Practical Design Considerations for Ultra-High Resolution Electron Lenses

1980 ◽  
Vol 38 ◽  
pp. 266-269
Author(s):  
Y. Harada ◽  
K. Tsuno ◽  
Y. Arai
Keyword(s):  
Optical Properties ◽  
High Resolution ◽  
Chromatic Aberration ◽  
Point Of View ◽  
Pole Piece ◽  
Axial Field ◽  
Design Considerations ◽  
Resolution Electron ◽  
Practical Design ◽  
Peak Flux

Magnetic objective lenses, from the point of view of pole piece geometry, can he roughly classified into two types, viz., symmetrical and asymmetrical. In the case of the former, the optical properties have been calculated by several authors1-3) and the results would appear to suggest that, in order to reduce the spherical and chromatic aberration coefficients, Cs and Cc, it is necessary to decrease the half-width value of the axial field distribution and to increase the peak flux density. The expressions for either minimum Cs or minimum Cc were presented in the form of ‘universal’ curves by Mulvey and Wallington4).

Design considerations in online surveys

2003 ◽  
Author(s):  
Kimberly Erickson ◽  
Tracey E. Rizzuto
Keyword(s):  
Online Surveys ◽  
Design Considerations

SARI : A User-Oriented Data Bank System for Medical Applications

1976 ◽  
Vol 15 (02) ◽  
pp. 69-74
Author(s):  
M. Goldberg ◽  
B. Doyon
Keyword(s):  
Data Base ◽  
Personal Data ◽  
Data Bank ◽  
Medical Applications ◽  
Basic Principles ◽  
Base Management ◽  
General Data ◽  
Privacy Problem ◽  
Bank System ◽  
Made In

This paper describes a general data base management package, devoted to medical applications. SARI is a user-oriented system, able to take into account applications very different by their nature, structure, size, operating procedures and general objectives, without any specific programming. It can be used in conversational mode by users with no previous knowledge of computers, such as physicians or medical clerks.As medical data are often personal data, the privacy problem is emphasized and a satisfactory solution implemented in SARI.The basic principles of the data base and program organization are described ; specific efforts have been made in order to increase compactness and to make maintenance easy.Several medical applications are now operational with SARI. The next steps will mainly consist in the implementation of highly sophisticated functions.

Sign in / Sign up

Export Citation Format

Share Document