A novel hole drilling method for plate Luneberg lens antenna

2014 ◽  
Author(s):  
Zhihui Yao ◽  
Yanhui Liu ◽  
Xiaoping Xiong ◽  
Liang Zhang ◽  
Longfang Ye ◽  
...  
Keyword(s):  
Hole Drilling ◽  
Lens Antenna ◽  
Hole Drilling Method ◽  
Drilling Method ◽  
Luneberg Lens

Residual Stress Measurements in an Autofrettage Tube Using Hole Drilling Method

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Hamid Jahed ◽  
Mohammad Reza Faritus ◽  
Zeinab Jahed
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Hoop Stress ◽  
Test Method ◽  
Test Material ◽  
Hole Drilling ◽  
Hole Drilling Method ◽  
Ring Sample ◽  
Drilling Method ◽  
American Society

Relieved strains due to drilling hole in a ring sample cut from an autofrettage cylinder are measured. Measured strains are then transformed to residual stresses using calibration constants and mathematical relations of elasticity based on ASTM standard recommendations (American Society for Testing and Materials, ASTM E 837-08, 2008, “Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method,” American Society for Testing and Materials). The hydraulic autofrettage is pressurizing a closed-end long cylinder beyond its elastic limits and subsequently removing the pressure. In contrast to three-dimensional stress state in the autofrettage tube, the stress measurement in hole drilling method is performed on a traction free surface formed from cutting the ring sample. The process of cutting the ring sample from a long autofrettaged tube is simulated using finite element method (FEM) and the redistribution of the residual stress due to the cut is discussed. Hence, transformation of the hole drilling measurements on the ring slice to the autofrettage residual stresses is revealed. The residual stresses are also predicted by variable material properties (VMP) method (Jahed, H., and Dubey, R. N., 1997, “An Axisymmetric Method of Elastic-Plastic Analysis Capable of Predicting Residual Stress Field,” Trans. ASME J. Pressure Vessel Technol., 119, pp. 264–273) using real loading and unloading behavior of the test material. Prediction results for residual hoop stress agree very well with the measurements. However, radial stress predictions are less than measured values particularly in the middle of the ring. To remove the discrepancy in radial residual stresses, the measured residual hoop stress that shows a self-balanced distribution was taken as the basis for calculating residual radial stresses using field equations of elasticity. The obtained residual stresses were improved a lot and were in good agreement with the VMP solution.

scholarly journals Incremental Hole-Drilling Method Vs. Thin Components: A Simple Correction Approach

2014 ◽  
Vol 996 ◽  
pp. 283-288 ◽  
Author(s):  
Esther Held ◽  
Simone Schuster ◽  
Jens Gibmeier
Keyword(s):  
Residual Stress ◽  
Thin Metal ◽  
Hole Drilling ◽  
Depth Profiles ◽  
Hole Drilling Method ◽  
Incremental Hole Drilling ◽  
Metal Sheets ◽  
Drilling Method ◽  
Measured Strain ◽  
The Impact

The incremental hole-drilling method is a widely used technique to determine residual stress depth profiles in technical components. Its application is limited in respect to the components geometry, for instance the components thickness. In this paper, a direct correction of the measured strain relaxations is proposed to consider the impact of deviant geometries, here the component thickness, on the residual stress evaluation that moreover, allows the application of commercially available evaluation software. The herein proposed approach is based on finite element simulation of the incremental hole drilling. The simulated strain relaxations for thin metal sheets are evaluated with an algorithm as used in commercially available evaluation software (i) for uncorrected data as well as (ii) for strain data corrected by the proposed correction procedure. It is shown that the correction approach leads to a significant improvement of the measurement accuracy. Further, by means of the approach residual stress depth profiles in thin metal sheets can be as usual determined using commercial evaluation software for the incremental hole-drilling method regardless of the algorithm used, i.e. differential or integral.

Sign in / Sign up

Export Citation Format

Share Document