A new CCFL inverter circuit far AMLCD panels results in significantly higher efficiency and brightness

Author(s):  
M.K. Nalbant
Keyword(s):  
Author(s):  
Abiodun Ogunseye ◽  
Daniel Ogheneovo Johnson

A power inverter circuits is normally designed to meet its design specifications when the applied input DC voltage is within specified tolerance limits. Thus, single input inverters are usually specified to work from a DC source having a fixed nominal voltage. This limits the usefulness of the inverter circuit when a DC source having the specified nominal voltage is not available. In this work, a modified square wave inverter system that is specified to work properly from batteries with nominal voltages of 6, 12, 18 and 24 V was designed.  A model of the microcontroller-based circuit was developed with Proteus® software and its firmware was written in C language using the MicroC® development tool. A prototype of the circuit was constructed and then tested.  The constructed circuit was found to work properly by producing a 50 Hz modified square waveform when it was powered from batteries having nominal voltages of 6 V, 12 V, 18 V and 24 V.


2005 ◽  
Vol 13 (5) ◽  
pp. 429 ◽  
Author(s):  
Hajime Akimoto ◽  
Hiroshi Kageyama ◽  
Mitsuhide Miyamoto ◽  
Yoshiteru Shimizu ◽  
Naruhiko Kasai ◽  
...  

2021 ◽  
Author(s):  
Anubha Bilgaiyan ◽  
Seung-Il Cho ◽  
Miho Abiko ◽  
Kaori Watanabe ◽  
Makoto Mizukami

Abstract The low mobility and large contact resistance in organic thin-film transistors (OTFTs) are the two major limiting factors in the development of high-performance organic logic circuits. Here, solution-processed high-performance OTFTs and circuits are reported with a polymeric gate dielectric and 6,6 bis (trans-4-butylcyclohexyl)-dinaphtho[2,1-b:2,1-f ]thieno[3,2-b]thiophene (4H-21DNTT) for the organic semiconducting layer. By optimizing and controlling the fabrication conditions, a record high saturation mobility of 8.8 cm2V− 1s− 1 was demonstrated as well as large on/off ratios (> 106) for relatively short channel lengths of 15 µm and an average carrier mobility of 10.5 cm2V-1s-1 for long channel length OTFTs (> 50 µm). The pseudo-CMOS inverter circuit with a channel length of 15 µm exhibited sharp switching characteristics with a high signal gain of 31.5 at a supply voltage of 20 V. In addition to the inverter circuit, NAND logic circuits were further investigated, which also exhibited remarkable logic characteristics, with a high gain, an operating frequency of 5 kHz, and a short propagation delay of 22.1 µs. The uniform and reproducible performance of 4H-21DNTT OTFTs show potential for large-area, low-cost real-world applications on industry-compatible bottom-contact substrates.


Instruments ◽  
2020 ◽  
Vol 4 (1) ◽  
pp. 7 ◽  
Author(s):  
Huatan Chen ◽  
Gaofeng Zheng ◽  
Juan Liu ◽  
Jiaxin Jiang ◽  
Guoyi Kang ◽  
...  

The precise manufacturing of micro/nano structures is the key to the rapid development of flexible micro/nano systems. In this paper, a sinusoidal high-voltage alternating current (AC) power is designed for electrohydrodynamic direct-writing (EDW) technology. A push-pull converting circuit is utilized as the direct current (DC) voltage regulator power of a full-bridge inverter circuit. A single-phase full-bridge inverter circuit is used to output the controllable AC voltage, which is then boost-filtered to output the high-voltage sinusoidal AC signal. The amplitude of the output sinusoidal voltage is proportional to the input voltage and the modulation degree of the sinusoidal pulse width modulation (SPWM) inverter circuit. Then, the designed sinusoidal high-voltage AC power is used in the AC EDW process to print micro-droplets. The deposition frequency and the average diameter of droplets can be effectively controlled by adjusting the voltage amplitude and the voltage frequency. The design of this sinusoidal high-voltage AC power will promote research on the applications of EDW technology in the field of micro/nano manufacturing.


2011 ◽  
Vol 354-355 ◽  
pp. 1394-1399
Author(s):  
Su Rong Qu ◽  
Zhong Yang Zhang

IGCT is a kind of new type power electronic device which developed from GTO and IGBT . In this paper, Author based on analysis of the internal structure of GTO, shows how GTO development IGCT through technical methods.Through simulation of its off and on performance, the work curve and comparing results of the two devices are given. Then on two components of the inverter circuits are analyzed and compared. Thinking in large power AC drive locomotive, IGCT inverter is greatly simplifier than GTO inverter circuit, and superior performance,it will become the main converter for AC driving locomotive.


2007 ◽  
Vol 124-126 ◽  
pp. 407-410
Author(s):  
Sang Chul Lim ◽  
Seong Hyun Kim ◽  
Gi Heon Kim ◽  
Jae Bon Koo ◽  
Jung Hun Lee ◽  
...  

We report the effects of instability with gate dielectrics of pentacene thin film transistors (OTFTs) inverter circuits. We used to the UV sensitive curable resin and poly-4-vinylphenol(PVP) by gate dielectrics. The inverter supply bias is VDD= -40 V. For a given dielectric thickness and applied voltage, pentacene OTFTs with inverter circuits measurements field effect mobility, on-off current ratio, Vth. The field effect mobility 0.03~0.07 cm2/Vs, and the threshold voltage is -3.3 V ~ -8.8 V. The on- and off-state currents ratio is about 103~106. From the OTFT device and inverter circuit measurement, we observed hysteresis behavior was caused by interface states of between the gate insulator and the pentacene semiconductor layer.


Sign in / Sign up

Export Citation Format

Share Document