scholarly journals Model Predictive Control Method With NP Voltage Balance by Offset Voltage Injection for Three-Phase Three-Level NPC Inverter

IEEE Access ◽  
2020 ◽  
Vol 8 ◽  
pp. 172175-172195 ◽  
Author(s):  
Eun-Su Jun ◽  
Minh Hoang Nguyen ◽  
Sang-Shin Kwak
Keyword(s):  
Model Predictive Control ◽  
Predictive Control ◽  
Control Method ◽  
Offset Voltage ◽  
Three Phase ◽  
Voltage Balance

scholarly journals Three-Phase Three-Level Neutral Point Clamped Rectifier with Predictive Control Method without Employing Weighting Factor

2020 ◽  
Vol 10 (15) ◽  
pp. 5149 ◽  
Author(s):  
Eun-Su Jun ◽  
Minh Hoang Nguyen ◽  
Sangshin Kwak
Keyword(s):  
Predictive Control ◽  
Control Method ◽  
Weighting Factor ◽  
Neutral Point ◽  
Control Methods ◽  
Offset Voltage ◽  
Three Phase ◽  
Sinusoidal Input ◽  
Capacitor Voltage ◽  
Voltage Balance

A predictive control method using injected offset voltage to achieve neutral point (NP) voltage balance of three-phase three-level neutral point clamped (NP) rectifiers, without employing a weighting factor, is proposed in this study. One of the biggest problems with the three-level NP rectifiers is the dc link capacitor voltage imbalance. Therefore, it is necessary to maintain the balance of the NP voltage in addition to synthesize the three-phase sinusoidal input current by control methods. Conventional predictive control methods for the NP rectifiers have used a weighting factor in a cost function that determines the control ratio of the input currents and the capacitor voltage balance. As a result, it is burdensome to empirically redesign the weighting factor when the rectifiers’ parameter values and control conditions change. Unlike the conventional methods, the proposed approach without the weighting factor can significantly eliminate differences between two DC capacitor voltages by utilizing an offset voltage, which is generated by using the difference between the upper and lower capacitor voltages. Consequently, the proposed approach using the offset voltage injection can control the input currents and retain the balance of NP voltage. Simulation and experiments are presented to verify the correctness of the NP voltage balancing of the proposed control method.

Model predictive control method with common-mode voltage suppression for dual three-phase permanent magnet synchronous motor

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1453-1460
Author(s):  
Zhifeng Zhang ◽  
Yue Wu ◽  
Sicong Ye
Keyword(s):  
Computational Complexity ◽  
Model Predictive Control ◽  
Predictive Control ◽  
Control Method ◽  
Permanent Magnet Synchronous Motor ◽  
Synchronous Motor ◽  
Common Mode ◽  
Current Harmonics ◽  
Common Mode Voltage ◽  
Three Phase

Recently, the interest in model predictive control (MPC) and dual three-phase drives has been growing rapidly. Due to the high redundancy of voltage vector in the system composed of dual three-phase permanent magnetic synchronous motor (PMSM) and six-phase inverter, the computational complexity and current harmonics of MPC are high. In addition, the zero vector has been used by traditional MPC, which will cause higher common-mode voltage. In this paper, a novel MPC method with twice predictions and synthetic vectors is proposed which can not only suppress common-mode voltage, but also reduce computational complexity and current harmonics. The mathematical model of a dual three-phase PMSM are verified by the experimental results under the common-mode voltage suppression.

scholarly journals A Novel Adaptive Model Predictive Control Based Three-Phase Inverter Current Control Method

2019 ◽  
Vol 9 (24) ◽  
pp. 5413 ◽  
Author(s):  
Mingyu Lei ◽  
Ying Zhang ◽  
Lexuan Meng ◽  
Yibo Wang ◽  
Zilong Yang ◽  
...  
Keyword(s):  
Model Predictive Control ◽  
Predictive Control ◽  
Control Method ◽  
Dynamic Performance ◽  
Current Control ◽  
Three Phase ◽  
Modification Method ◽  
Adaptive Model Predictive Control ◽  
Three Phase Inverter ◽  
Control Accuracy

This paper proposes a novel current control method based on Model Predictive Control (MPC) for three-phase inverters. The proposed method is based on an Adaptive MPC (A-MPC) with a PWM modulation. An innovative model parameter estimation and modification method is also proposed, leading to enhanced control accuracy. Comparing with traditional current control methods, such as PI and PR control, the proposed method has better dynamic performance. The transient dynamics, i.e., recovery time and overshoot, have been considerably improved. Simulation and experimental results are presented to validate the effectiveness of the proposal.

scholarly journals A Compromising Approach to Switching Losses and Waveform Quality in Three-phase Voltage Source Converters with Double-vector based Predictive Control Method

Electronics ◽  
2019 ◽  
Vol 8 (11) ◽  
pp. 1372
Author(s):  
Jun ◽  
Kwak
Keyword(s):  
Predictive Control ◽  
Output Voltage ◽  
Control Method ◽  
Input Current ◽  
Voltage Source ◽  
Current Waveform ◽  
Source Power ◽  
Switching Losses ◽  
Offset Voltage ◽  
Three Phase

A switching losses reduction technique for the model predictive control (MPC) algorithm, which uses double-vector in the three-phase rectifier, is presented. The proposed method controls the output voltage of the rectifier by using reference rectifier input voltages with the offset voltage injection to reduce the switching losses. One leg with the largest source current among the three legs in the rectifier is clamped to either the positive or negative output voltage in the proposed method. The proposed method calculates the offset voltage on the basis of the future rectifier input voltages obtained by the reference rectifier input voltage, output voltage, and the source currents in every sampling period, so the clamping region in the leg conducting the largest input current is optimally varied depending on the reference rectifier input voltages and the source currents. Therefore, the proposed method can reduce the switching losses of the rectifier regardless of the different source power factor angle. Due to the effects of clamped legs, the quality of the input current waveform inevitably deteriorated. Thus, in the proposed method, double vectors were utilized to avoid degradation of current qualities and achieved compromised performance by reducing switching losses and keeping the current waveform quality. A performance comparison between the conventional method and the proposed method was made to show performance differences. Additionally, the simulation and experiment were conducted to verify the effectiveness of the proposed method.

Sign in / Sign up

Export Citation Format

Share Document