Modeling and control of a heated air intake homogeneous charge compression ignition (HCCI) engine

2010 ◽  
Author(s):  
Donghoon Lee ◽  
A G Stefanopoulou ◽  
S Makkapati ◽  
M Jankovic
Keyword(s):  
Homogeneous Charge Compression Ignition ◽  
Compression Ignition ◽  
Modeling And Control ◽  
Hcci Engine ◽  
Heated Air ◽  
Air Intake ◽  
And Control ◽  
Homogeneous Charge

scholarly journals Influence of gas composition on the combustion and efficiency of a homogeneous charge compression ignition engine system fuelled with methanol reformed gases

2008 ◽  
Vol 9 (5) ◽  
pp. 399-408 ◽  
Author(s):  
T Shudo
Keyword(s):  
Homogeneous Charge Compression Ignition ◽  
Waste Heat ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Temperature Oxidation ◽  
Hcci Engine ◽  
Recovery Capacity ◽  
Exhaust Heat ◽  
Engine System ◽  
Homogeneous Charge

A homogeneous charge compression ignition (HCCI) engine system fuelled with dimethyl ether (DME) and methanol-reformed gas (MRG), both produced from methanol by onboard reformers using exhaust heat, has been proposed in previous research. Adjusting the proportions of DME and MRG with different ignition properties effectively controlled the ignition timing and load in HCCI combustion. The use of the single liquid fuel, methanol, also eliminates the inconvenience of carrying two fuels while maintaining the effective ignition control effect. Because reactions producing DME and MRG from methanol are endothermic, a part of the exhaust gas heat energy can be recovered during the fuel reforming. Methanol can be reformed into various compositions of hydrogen, carbon monoxide, and carbon dioxide. The present paper aims to establish the optimum MRG composition for the system in terms of ignition control and overall efficiency. The results show that an increased hydrogen fraction in MRG retards the onset of high-temperature oxidation and permits operation with higher equivalence ratios. However, the MRG composition affects the engine efficiency only a little, and the MRG produced by the thermal decomposition having the best waste-heat recovery capacity brings the highest overall thermal efficiency in the HCCI engine system fuelled with DME and MRG.

Physical Modeling and Control of a Multi-Cylinder HCCI Engine

2009 ◽  
Author(s):  
Nikhil Ravi ◽  
Matthew J. Roelle ◽  
Hsien-Hsin Liao ◽  
Adam F. Jungkunz ◽  
Chen-Fang Chang ◽  
...  
Keyword(s):  
Direct Injection ◽  
Work Output ◽  
Compression Ignition ◽  
Piston Engine ◽  
Modeling And Control ◽  
Hcci Engine ◽  
Operating Region ◽  
Control Scheme ◽  
And Control ◽  
Wide Operating

Homogeneous charge compression ignition (HCCI) is one of the most promising piston-engine concepts for the future, providing significantly improved efficiency and emissions characteristics relative to current technologies. This paper presents a framework for controlling a multi-cylinder HCCI engine with exhaust recompression and direct injection of fuel into the cylinder. A physical model is used to describe the HCCI process, with the model states being closely linked to the thermodynamic state of the cylinder constituents. Separability between the effects of the control inputs on the desired outputs provides an opportunity to develop a simple linear control scheme, where the fuel is used to control the work output and the valve timings are used to control the phasing of combustion. Experimental results show good tracking of both the work output and combustion phasing over a wide operating region. In addition, the controller is able to balance out differences between cylinders, and reduce the cycle-to-cycle variability of combustion.

Sign in / Sign up

Export Citation Format

Share Document