An extension to operational space for kinematically redundant manipulators: kinematics and dynamics

2000 ◽  
Vol 16 (5) ◽  
pp. 592-596 ◽  
Author(s):  
Pyung-Hua Chang ◽  
Ki Cheol Park ◽  
Sukhan Lee
Keyword(s):  
Kinematics And Dynamics ◽  
Redundant Manipulators ◽  
Operational Space

RANCANG BANGUN MESIN PEMOTONG RUMPUT TENAGA SURYA UNTUK NAVIGASI

2015 ◽  
Vol 1 (1) ◽  
pp. 5-16
Author(s):  
John Ohoiwutun
Keyword(s):  
High Speed ◽  
Solar Power ◽  
Human Life ◽  
Operating Cost ◽  
Fuel Oil ◽  
Kinematics And Dynamics ◽  
Control Input ◽  
High Speed Cutting ◽  
Lawn Mower ◽  
Coal Fuel

Utilization of conventional energy sources such as coal, fuel oil, natural gas and others on the one hand has a low operating cost, but on the other side of the barriers is the greater source of diminishing returns and, more importantly, the emergence of environmental pollution problems dangerous to human life. This study aims to formulate the kinematics and dynamics to determine the movement of Solar Power Mower. In this study, using solar power as an energy source to charge the battery which then runs the robot. Design and research was conducted in the Department of Mechanical Workshop Faculty of Engineering, University of Hasanuddin of Gowa. Control system used is a manual system using radio wave transmitter and receiver which in turn drive the robot in the direction intended. Experimental results showed that treatment with three variations of the speed of 6.63 m / s, 8.84 m / s and 15.89 m / sec then obtained the best results occur in grass cutting 15.89 sec and high-speed cutting grass 5 cm. Formulation of kinematics and dynamics for lawn mowers, there are 2 control input variables, x and y ̇ ̇ 3 to control the output variables x, y and θ so that there is one variable redudant. Keywords: mobile robots, lawn mower, solar power

Effect of Rope Skipping Techniques on Kinematics and Dynamics of Motion

2014 ◽  
Vol 8 (6) ◽  
pp. 1037
Author(s):  
Ratna Chow ◽  
Ahmad Faizal Salleh ◽  
Mohd Shahril Salim ◽  
Wan Mohd Radzi Bin Rusli ◽  
Norazian Abd. Razak ◽  
...  
Keyword(s):  
Kinematics And Dynamics ◽  
Rope Skipping

Kinematics and dynamics of lava flows

2005 ◽  
Author(s):  
Michael Manga ◽  
Guido Ventura
Keyword(s):  
Lava Flows ◽  
Kinematics And Dynamics

Investigating the potential of redundant manipulators in narrow channels

2020 ◽  
pp. 095440622096451
Author(s):  
Ashish Singla ◽  
Jyotindra Narayan ◽  
Himanshu Arora
Keyword(s):  
Case Studies ◽  
Fuzzy Inference ◽  
Redundant Manipulators ◽  
Redundancy Resolution ◽  
Inference System ◽  
Narrow Channels ◽  
First Case ◽  
Task Priority ◽  
Patient Side

In this paper, an attempt has been made to investigate the potential of redundant manipulators, while tracking trajectories in narrow channels. The behavior of redundant manipulators is important in many challenging applications like under-water welding in narrow tanks, checking the blockage in sewerage pipes, performing a laparoscopy operation etc. To demonstrate this snake-like behavior, redundancy resolution scheme is utilized using two different approaches. The first approach is based on the concept of task priority, where a given task is split and prioritize into several subtasks like singularity avoidance, obstacle avoidance, torque minimization, and position preference over orientation etc. The second approach is based on Adaptive Neuro Fuzzy Inference System (ANFIS), where the training is provided through given datasets and the results are back-propagated using augmentation of neural networks with fuzzy logics. Three case studies are considered in this work to demonstrate the redundancy resolution of serial manipulators. The first case study of 3-link manipulator is attempted with both the approaches, where the objective is to track the desired trajectory while avoiding multiple obstacles. The second case study of 7-link manipulator, tracking trajectory in a narrow channel, is investigated using the concept of task priority. The realistic application of minimum-invasive surgery (MIS) based trajectory tracking is considered as the third case study, which is attempted using ANFIS approach. The 5-link spatial redundant manipulator, also known as a patient-side manipulator being developed at CSIR-CSIO, Chandigarh is used to track the desired surgical cuts. Through the three case studies, it is well demonstrated that both the approaches are giving satisfactory results.

Sign in / Sign up

Export Citation Format

Share Document