Efficiency of excitation of piezoceramic transducers at antiresonance frequency

2002 ◽  
Vol 49 (4) ◽  
pp. 484-494 ◽  
Author(s):  
A.V. Mezheritsky
Keyword(s):  
Antiresonance Frequency

Quantitative Analysis of Power Leakage in an Film Bulk Acoustic Resonator Device at the Antiresonance Frequency

2010 ◽  
Vol 49 (7) ◽  
pp. 07HD11 ◽  
Author(s):  
Florian Thalmayr ◽  
Ken-ya Hashimoto ◽  
Masanori Ueda ◽  
Tatsuya Omori ◽  
Masatsune Yamaguchi
Keyword(s):  
Quantitative Analysis ◽  
Acoustic Resonator ◽  
Antiresonance Frequency ◽  
Film Bulk Acoustic Resonator ◽  
Film Bulk ◽  
Power Leakage

Sensitivity of Acoustic Resonance Properties to a Change in Volume of Piriform Sinuses

2016 ◽  
Vol 821 ◽  
pp. 671-676 ◽  
Author(s):  
Vojtěch Radolf
Keyword(s):  
Computational Models ◽  
Vocal Tract ◽  
Acoustic Resonance ◽  
Mode Shapes ◽  
Finite Element Models ◽  
Antiresonance Frequency ◽  
Resonance Frequencies ◽  
Resonance Properties ◽  
1D Model

Piriform sinuses (PS), side branches of the human vocal tract, produce extra resonances and antiresonances which influence the quality of produced voice. These acoustic resonant characteristics can be numerically simulated by 3D finite element models of the vocal tract with lateral cavities. Computations that use these accurate methods are very time consuming, therefore this study introduces a simplified 1D mathematical model to analyse acoustical effects of side branches. Although the 1D model cannot capture higher-frequency transversal mode shapes, the resulted changes caused by piriform sinuses partially correspond to recent findings of 3D computational models. New pair of resonances around 5 kHz followed by an antiresonance frequency were detected in the results of the model including PS. The first four resonance frequencies lying below the first new resonance of PS decreased with increasing PS volume and similarly both the new resonances of PS. The higher original resonances increased with increasing PS volume.

Investigation on Vibro-Acoustic Characteristics from Submerged Cylindrical Shell with Double Damping Layers

2013 ◽  
Vol 345 ◽  
pp. 94-98
Author(s):  
Chao Zhang ◽  
De Jiang Shang ◽  
Qi Li
Keyword(s):  
Cylindrical Shell ◽  
Low Frequency ◽  
Acoustic Characteristics ◽  
Radiated Power ◽  
Shell Models ◽  
Antiresonance Frequency ◽  
Shell Motion ◽  
Vibration And Sound Radiation ◽  
Thin Shell Theory ◽  
Large Frequency

The vibration and sound radiation from submerged cylindrical shell with double damping layers are presented. The cylindrical shell motion was described with classical thin shell theory. The double damping layers motion was described with the Navier viscoelasticity theory. For different Youngs modulus parameters of double damping layers, the sound radiated power and the radial quadratic velocity of cylindrical shell models were calculated and analyzed. The results show that the sound radiated power and radial quadratic velocity are reduced to varying degrees due to double damping layers in a large frequency domain except low frequency. The double damping layer with soft inner layer and hard outer layer can make the sound radiated peaks move to high frequency, can help to reduce the radial quadratic velocity on outer surface of damping layer, and can help to reduce the vibration of model at antiresonance frequency.

Measuring Methods for High–Power Characteristics of Piezoelectric Materials

1994 ◽  
Vol 360 ◽  
Author(s):  
Seiji Hirose ◽  
Sadayuki Takahashi ◽  
Kenji Uchino ◽  
Manabu Aoyagi ◽  
Yoshiro Tomikawa
Keyword(s):  
High Power ◽  
Temperature Rise ◽  
Measurement Method ◽  
High Efficiency ◽  
Piezoelectric Materials ◽  
Stable State ◽  
Ultrasonic Power ◽  
Power Characteristics ◽  
Vibrational Velocity ◽  
Antiresonance Frequency

AbstractTwo kinds of measuring method of the high-power characteristics of piezoelectric transducers are described. One is the measurement method at the resonance frequency and another is the measurement method at the antiresonance frequency. The vibrational velocity dependences of the equivalent circuit constants and the temperature rise were measured by using each measurement method under the constant vibrational velocity control. These results are useful for designing the ultrasonic power devices such as the ultrasonic motor, and also useful for investigating the new advanced piezoelectric materials for high power use. Especially, by using the results obtained at the antiresonance frequency, a stable state driving method, named as antiresonance driving, with high-efficiency and low-temperature rise can be achieved.

Nonlinear elastic phenomena near the radial antiresonance frequency in piezoceramic discs

2007 ◽  
Vol 19 (4) ◽  
pp. 427-431 ◽  
Author(s):  
A. Albareda ◽  
R. Pérez ◽  
J. E. García ◽  
D. A. Ochoa
Keyword(s):  
Antiresonance Frequency ◽  
Nonlinear Elastic

scholarly journals Damage Detection of Laminated Rubber Bearings Based on the Antiresonance Frequencies of Periodic Structure and Its Sensitivity Analysis

2022 ◽  
Vol 2022 ◽  
pp. 1-18
Author(s):  
Ying Zhang ◽  
Hongping Zhu ◽  
Shun Weng
Keyword(s):  
Sensitivity Analysis ◽  
Damage Detection ◽  
Characteristic Equation ◽  
Dynamic Stiffness ◽  
Steel Structure ◽  
Seismic Energy ◽  
Detection Scheme ◽  
Rubber Layer ◽  
Antiresonance Frequency ◽  
Rubber Bearings

An isolation bearing consumes most of the seismic energy of a structure and is vulnerable to destruction. The performance of isolation bearings is usually evaluated according to the global stiffness and energy dissipation capacity. However, the early minor damage in isolation bearings is difficult to identify. In this study, a damage detection scheme for the isolation bearing is proposed by focusing on the antiresonance of the quasiperiodic structure. Firstly, a laminated rubber bearing was simplified as a monocoupled periodic rubber-steel structure. The characteristic equation of the driving point antiresonance frequency of the periodic system was achieved via the dynamic stiffness method. Secondly, the sensitivity coefficient of the driving point antiresonance, which was obtained from the first-order derivative of the antiresonance frequency, with respect to the damage scaling parameter was derived using the antiresonance frequency characteristic equation. Thirdly, the optimised driving points of the antiresonance frequencies were selected by means of sensitivity analysis. Finally, from the measured changes in the antiresonance frequencies, the damage was identified by solving the sensitivity identification equation via a numerical optimisation method. The application of the proposed method to laminated rubber bearings under various damage cases demonstrates the feasibility of this method. This study has proven that changes in the shear modulus of each rubber layer can be identified accurately.

High power characteristics at antiresonance frequency of piezoelectric transducers

Ultrasonics ◽  
1996 ◽  
Vol 34 (2-5) ◽  
pp. 213-217 ◽  
Author(s):  
Seiji Hirose ◽  
Manabu Aoyagi ◽  
Yoshiro Tomikawa ◽  
Sadayuki Takahashi ◽  
Kenji Uchino
Keyword(s):  
High Power ◽  
Piezoelectric Transducers ◽  
Power Characteristics ◽  
Antiresonance Frequency

scholarly journals Modal Analysis of 27 mm Piezo Electric Plate for Small-Scale Underwater Sonar-Based Navigation

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
M. O. Afolayan ◽  
D. S. Yawas ◽  
C. O. Folayan ◽  
S. Y. Aku
Keyword(s):  
Resonance Frequency ◽  
Modal Analysis ◽  
Robotic Fish ◽  
Small Scale ◽  
Simulation Process ◽  
Antiresonance Frequency ◽  
Input Load ◽  
Ultrasonic Transmitters ◽  
Piezo Electric

This work presents progress towards the development of a small-scale, purely sonar-based navigation device for a robotic fish (~394 mm long). Aperture overloading of small (5 mm diameter) ultrasonic transmitters does not allow them to be used effectively inside water. A test on a 27 mm diameter buzzer piezo plate shows promising performance under water at frequencies from 4.5 kHz to 80 kHz. ANSYS-based simulation was therefore used to find modal frequencies at higher frequencies so as to optimize this encouraging result. The simulation process also discovered several antiresonant frequencies such as 38.5 kHz, 54 kHz, and 57.5 kHz. All frequencies above the 8th harmonic (10,589.02 Hz) are out of phase with the input load except a resonance frequency of 42.5 kHz and an antiresonance frequency of 56.5 kHz. Also, the first harmonic (1,648.73 Hz) is the only frequency that gave a nodal deformation.

scholarly journals Study on Transmission Characteristics of Vertical Rail Vibrations in Ballast Track

2017 ◽  
Vol 2017 ◽  
pp. 1-13 ◽  
Author(s):  
Xi Sheng ◽  
Caiyou Zhao ◽  
Ping Wang ◽  
Dongya Liu
Keyword(s):  
Transmission Rate ◽  
Spectral Element ◽  
Transmission Characteristics ◽  
Low Frequencies ◽  
High Frequencies ◽  
Vibration Absorption ◽  
High Attenuation ◽  
Antiresonance Frequency ◽  
Ballast Track ◽  
Track Substructure

A plane half-track model and a periodic track-substructure model are established. The spectral element method and spectral transfer matrix method are developed and applied to investigate the track decay rate (TDR) and transmission rate (TR) of the vertical rail vibrations, which can reflect the transmission characteristics in the longitudinal and downward directions, respectively. Furthermore, the effects of different track parameters on TDR and TR are investigated. The results show that the antiresonance frequency of the rail and the out-of-phase resonance frequency of the rail and sleeper form the boundary frequencies of the high-attenuation zone for longwise vibration transmission, where the vibration absorption of the sleeper is significant. The downward transmissibility of vertical rail vibrations is greatest around the antiresonance frequency of the rail. Vertical rail vibrations are primarily transmitted in the downward direction at low frequencies, while they are mainly transmitted along the rail at high frequencies. Stiffer rail pads can make more vibrations transmitted downwards to the sleeper above the antiresonance frequency of the rail, while the changes of other track parameters have different effects on the transmission characteristics. Additionally, a field measurement is performed for verification, and the simulations are well consistent with measurements.

scholarly journals Comparison of Damage Detection Methods Depending on FRFs within Specified Frequency Ranges

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Yong-Su Kim ◽  
Hee-Chang Eun
Keyword(s):  
Damage Detection ◽  
Resonance Frequency ◽  
Structural Damage ◽  
Detection Methods ◽  
Frequency Range ◽  
Damage Indices ◽  
Antiresonance Frequency ◽  
Limited Frequency ◽  
Proper Orthogonal ◽  
Modified Forms

Structural damage can be detected using frequency response function (FRF) measured by an impact and the corresponding responses. The change in the mechanical properties of dynamic system for damage detection can seldom be estimated using FRF data extracted from a very limited frequency range. Proper orthogonal modes (POMs) from the FRFs extracted in given frequency ranges and their modified forms can be utilized as damage indices to detect damage. The POM-based damage detection methods must be sensitive to the selected FRFs. This work compares the effectiveness of the damage detection approaches taking the POMs estimated by the FRFs within five different frequency ranges including resonance frequency and antiresonance frequency. It is shown from a numerical example that the POMs extracted from the FRFs within antiresonance frequency ranges provide more explicit information on the damage locations than the ones within resonance frequency ranges.

Sign in / Sign up

Export Citation Format

Share Document