Estimate of indicated torque from crankshaft speed fluctuations: a model for the dynamics of the IC engine

1989 ◽  
Vol 38 (3) ◽  
pp. 168-179 ◽  
Author(s):  
G. Rizzoni
Keyword(s):  
Ic Engine ◽  
Speed Fluctuations

Methodologies to Compare IC Engine Power Assembly Interface Materials

2018 ◽  
Author(s):  
M R Sridhar ◽  
K A Harsha ◽  
Savio Sebastian ◽  
Souvik Math
Keyword(s):  
Ic Engine ◽  
Interface Materials ◽  
Engine Power

scholarly journals Cavitation between cylinder-liner and piston-ring in a new designed optical IC engine

2021 ◽  
pp. 146808742110080
Author(s):  
Jamshid Malekmohammadi Nouri ◽  
Ioannis Vasilakos ◽  
Youyou Yan
Keyword(s):  
High Speed ◽  
Contact Point ◽  
Cylinder Liner ◽  
Optical Methods ◽  
Engine Management System ◽  
Great Success ◽  
Ic Engine ◽  
Contact Points ◽  
Lubricant Flow ◽  
Cavitation Intensity

A new engine block with optical access has been designed and manufactured capable of running up to 3000 r/min with the same specification as the unmodified engine. The optical window allowed access to the full length of the liner over a width of 25 mm to investigate the lubricant flow and cavitation at contact point between the rings and cylinder-liner. In addition, it allowed good access into the combustion chamber to allow charged flow, spray and combustion visualisation and measurements using different optical methods. New custom engine management system with build in LabView allowed for the precise full control of the engine. The design of the new optical engine was a great success in producing high quality images of lubricant flow, cavitation formation and development at contact point at different engine speeds ranging from 208 to 3000 r/min and lubricant temperatures (30°C–70°C) using a high-speed camera. The results under motorised operation confirmed that there was no cavitation at contact points during the intake/exhaust strokes due to low in-cylinder presure, while during compression/expansion strokes, with high in-cylinder pressure, considerable cavities were observed, in particular, during the compression stroke. Lubricant temperatures had the effect of promoting cavities both in their intensity and covered ring area up to 50°C as expected. Beyond that, although the cavitation intensity increases further with temperature, its area reduces due to possible collapse of the cavitating bubbles at higher temperature. The change of engine speed from 208 to 800 r/min increased cavitating area considerably by 52% of the ring area and was further increased by 19% at 1000 r/min. After that, the results showed very small increase in cavitation area (1.3% at 2000 r/min) with similar intensity and distribution across the ring.

Modeling and validation of crankshaft speed fluctuations of a single-cylinder four-stroke diesel engine

2021 ◽  
pp. 095440702110262
Author(s):  
Mustafa Babagiray ◽  
Hamit Solmaz ◽  
Duygu İpci ◽  
Fatih Aksoy
Keyword(s):  
Diesel Engine ◽  
Dynamic Model ◽  
Moment Of Inertia ◽  
Mass Motion ◽  
Cylinder Pressure ◽  
Motion Equations ◽  
Single Cylinder ◽  
Mass Moment ◽  
Mass Moment Of Inertia ◽  
Speed Fluctuations

In this study, a dynamic model of a single-cylinder four-stroke diesel engine has been created, and the crankshaft speed fluctuations have been simulated and validated. The dynamic model of the engine consists of the motion equations of the piston, conrod, and crankshaft. Conrod motion was modeled by two translational and one angular motion equations, by considering the kinetic energy resulted from the mass moment of inertia and conrod mass. Motion equations involve in-cylinder gas pressure forces, hydrodynamic and dry friction, mass inertia moments of moving parts, starter moment, and external load moment. The In-cylinder pressure profile used in the model was obtained experimentally to increase the accuracy of the model. Pressure profiles were expressed mathematically using the Fourier series. The motion equations were solved by using the Taylor series method. The solution of the mathematical model was performed by coding in the MATLAB interface. Cyclic speed fluctuations obtained from the model were compared with experimental results and found compitable. A validated model was used to analyze the effects of in-cylinder pressure, mass moment of inertia of crankshaft and connecting rod, friction, and piston mass. In experiments for 1500, 1800, 2400, and 2700 rpm engine speeds, crankshaft speed fluctuations were observed as 12.84%, 8.04%, 5.02%, and 4.44%, respectively. In simulations performed for the same speeds, crankshaft speed fluctuations were calculated as 10.45%, 7.56%, 4.49%, and 3.65%. Besides, it was observed that the speed fluctuations decreased as the average crankshaft speed value increased. In the simulation for 157.07, 188.49, 219.91, 251.32, and 282.74 rad/s crankshaft speeds, crankshaft speed fluctuations occurred at rates of 10.45%, 7.56%, 5.84%, 4.49%, and 3.65%, respectively. The effective engine power was achieved as 5.25 kW at an average crankshaft angular speed of 219.91 rad/s. The power of friction loss in the engine was determined as 0.68 kW.

Sign in / Sign up

Export Citation Format

Share Document