scholarly journals Practical analysis of 3-D dynamic nonlinear magnetic field using time-periodic finite element method

1995 ◽  
Vol 31 (3) ◽  
pp. 1416-1419 ◽  
Author(s):  
T. Nakata ◽  
N. Takahashi ◽  
K. Fujiwara ◽  
K. Muramatsu ◽  
H. Ohashi ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Finite Element Method ◽  
Finite Element ◽  
Practical Analysis ◽  
Time Periodic ◽  
Element Method

scholarly journals Analysis of characteristics of electromagnets with shading coil using the time-periodic finite element method.

1985 ◽  
Vol 105 (5) ◽  
pp. 475-482
Author(s):  
Takayoshi Nakata ◽  
Yoshihiro Kawase ◽  
Takashi Matsubara ◽  
Syokichi Ito
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Time Periodic ◽  
Element Method

Time-Domain Parallel Finite-Element Method for Fast Magnetic Field Analysis of Induction Motors

2013 ◽  
Vol 49 (5) ◽  
pp. 2413-2416 ◽  
Author(s):  
Yasuhito Takahashi ◽  
Tadashi Tokumasu ◽  
Masafumi Fujita ◽  
Takeshi Iwashita ◽  
Hiroshi Nakashima ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Finite Element Method ◽  
Finite Element ◽  
Time Domain ◽  
Induction Motors ◽  
Field Analysis ◽  
Magnetic Field Analysis ◽  
Parallel Finite Element ◽  
Element Method

scholarly journals Magnetic Circuit Design and Magnetic Field Finite Element Analysis of Converging Stepped Magnetofluid Seal with Small Clearance

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Xiaolong Yang ◽  
Guohong Wang ◽  
Ruibo Zhang
Keyword(s):  
Magnetic Field ◽  
Finite Element Method ◽  
Finite Element ◽  
Circuit Design ◽  
Magnetic Circuit ◽  
Element Analysis ◽  
Small Clearance ◽  
Calculation Results ◽  
Theoretical Pressure ◽  
Element Method

The stepped magnetofluid seal is an effective method for improving the pressure ability of ordinary magnetofluid seals (OMS) with large clearance. At present, the research on stepped magnetofluid seal with less than 0.4 mm small clearance has not been carried out yet. The equivalent magnetic circuit design of converging stepped magnetofluid seal (CSMS) with small clearance has been carried out and verified by magnetic field finite element method based on the CSMS theory and magnetic circuit theory. The effects of the width of the axial seal position, the height of the radial seal position, the number of the pole tooth in the axial seal position, and the number of the pole tooth in the radial seal position on the theoretical pressure ability of the CSMS are investigated by numerical simulation. The calculation results are analyzed and discussed. The results show that the magnetic flux leakage at the junction of the permanent magnet and pole piece causes the higher pressure ability of the CSMS structure designed by the equivalent magnetic circuit method than that calculated by the magnetic field finite element method. When the width of the axial seal position is greater than the height of the radial seal position and the number of pole teeth in the axial seal position is less than the number of pole teeth in the radial seal position, the CSMS has the best effect. Compared with OMS with small clearance, CSMS has greater advantages.

scholarly journals Design and fabrication of a microelectromechanical system resonator based on two orthogonal silicon beams with integrated mirror for monitoring in-plane magnetic field

2019 ◽  
Vol 11 (7) ◽  
pp. 168781401985368 ◽  
Author(s):  
Jesús Acevedo-Mijangos ◽  
Antonio Ramírez-Treviño ◽  
Daniel A May-Arrioja ◽  
Patrick LiKamWa ◽  
Héctor Vázquez-Leal ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Finite Element Method ◽  
Finite Element ◽  
Resonant Frequency ◽  
Microelectromechanical Systems ◽  
Analytical Models ◽  
Complex Signal ◽  
Bending Vibration ◽  
Element Method ◽  
Silicon Beams

We present a resonant magnetic field sensor based on microelectromechanical systems technology with optical detection. The sensor has single resonator composed of two orthogonal silicon beams (600 µm × 26 µm × 2 µm) with an integrated mirror (50 µm × 34 µm × 0.11 µm) and gold tracks (16 µm × 0.11 µm). The resonator is fabricated using silicon-on-insulator wafer in a simple bulk micromachining process. The sensor has easy performance that allows its oscillation in the first bending vibration mode through the Lorentz force for monitoring in-plane magnetic field. Analytical models are developed to predict first bending resonant frequency, quality factor, and displacements of the resonator. In addition, finite element method models are obtained to estimate the resonator performance. The results of the proposed analytical models agree well with those of the finite element method models. For alternating electrical current of 30 mA, the sensor has a theoretical linear response, a first bending resonant frequency of 43.8 kHz, a sensitivity of 46.1 µm T−1, and a power consumption close to 54 mW. The experimental resonant frequency of the sensor is 53 kHz. The proposed sensor could be used for monitoring in-plane magnetic field without a complex signal conditioning system.

Sign in / Sign up

Export Citation Format

Share Document