3-D finite element time-varying fields and eddy currents in nonlinear thin steel channels

1991 ◽  
Vol 27 (5) ◽  
pp. 4008-4011 ◽  
Author(s):  
O.A. Mohammed ◽  
F.G. Uler
Keyword(s):  
Finite Element ◽  
Eddy Currents ◽  
Time Varying ◽  
Thin Steel

Integrity Assessment of a Free-Fall Lifeboat Launched From a FPSO

2015 ◽  
Author(s):  
Guomin Ji ◽  
Nabila Berchiche ◽  
Sébastien Fouques ◽  
Thomas Sauder ◽  
Svein-Arne Reinholdtsen
Keyword(s):  
Finite Element ◽  
Pressure Distribution ◽  
Structural Integrity ◽  
Dynamic Effect ◽  
Sensitivity Study ◽  
Computational Time ◽  
Load Factor ◽  
Time Varying ◽  
Integrity Assessment

The paper addresses the structural integrity assessment of lifeboat launched from floating production, storage and offloading (FPSO) vessels. The study is based on long-term drop lifeboat simulations accounting for more than 50 years of hindcast data of metocean conditions and corresponding FPSO motions. Selection of the load cases and strength analyses with high computational time is a challenge. The load cases analyzed are those corresponding to the 99th percentile of long term distribution of indicators for large slamming loads (CARXZ) or large submergence (Imaxsub). For six selected cases, the time-varying pressure distribution on the lifeboat hull during and after water impact is calculated by CFD simulations using StarCCM+. The finite element model (FEM) of the composite structure of the lifeboat is modelled by ABAQUS. Quasi-static finite element (FE) analyses are performed for the selected load cases. The structural integrity is assessed by the maximum stress and Tsai-Wu failure measure. In the present study, the load and resistance factors are combined and applied to the response. A sensitivity study is performed to investigate the non-linear load/response effects when the load factor is applied to the load. In addition, dynamic analysis is performed with the time-varying pressure distribution for selected case and the dynamic effect is investigated.

Influence of Axial Excitations and of Boundary Conditions on the Parametric Instability of a Beam

1995 ◽  
Author(s):  
Régis Dufour ◽  
Alain Berlioz ◽  
Thomas Streule
Keyword(s):  
Finite Element ◽  
Boundary Conditions ◽  
Ritz Method ◽  
Parametric Instability ◽  
Experimental Tests ◽  
Time Varying ◽  
Periodic Force ◽  
Modal Reduction ◽  
Time Varying Parameter ◽  
The Stability

Abstract In this paper the stability of the lateral dynamic behavior of a pinned-pinned, clamped-pinned and clamped-clamped beam under axial periodic force or torque is studied. The time-varying parameter equations are derived using the Rayleigh-Ritz method. The stability analysis of the solution is based on Floquet’s theory and investigated in detail. The Rayleigh-Ritz results are compared to those of a finite element modal reduction. It shows that the lateral instabilities of the beam depend on the forcing frequency, the type of excitation and the boundary conditions. Several experimental tests enable the validation of the numerical results.

scholarly journals Analysis of Dynamic Characteristics of a Propeller Blade Subjected to Large Material Removal in Milling

2020 ◽  
pp. 10-14
Author(s):  
Luyi Han ◽  
◽  
Riliang Liu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Dynamic Behavior ◽  
Dynamic Characteristics ◽  
Material Removal ◽  
Natural Frequencies ◽  
Machining Process ◽  
Time Varying ◽  
Propeller Blade ◽  
Large Material

A propeller blade, as a typical example of low-rigidity components, is prone to chatter and deformation in machining process, especially when large material removal is applied. In order to foresee the problems and then optimize the process, identification of the dynamic behavior of the workpiece is of great importance. This paper studies the dynamic characteristics of the workpiece in the machining process from plate to propeller blade using Finite Element Method. The results show that the time-varying natural frequencies of the workpiece decrease gradually at the beginning steps of the process due to the influence of material removal, and increases afterwards influenced by the geometry of the blade.

Sign in / Sign up

Export Citation Format

Share Document