scholarly journals Erratum: Photoneutron cross-section measurements in the Bi209(γ,xn) reaction with a new method of direct neutron-multiplicity sorting [Phys. Rev. C 96, 044604 (2017)]

2019 ◽  
Vol 99 (5) ◽  
Author(s):  
I. Gheorghe ◽  
H. Utsunomiya ◽  
S. Katayama ◽  
D. Filipescu ◽  
S. Belyshev ◽  
...  
Keyword(s):  
Cross Section ◽  
Neutron Multiplicity ◽  
New Method

Photoneutron cross-section measurements in the Bi209 ( γ,xn ) reaction with a new method of direct neutron-multiplicity sorting

2017 ◽  
Vol 96 (4) ◽  
Author(s):  
I. Gheorghe ◽  
H. Utsunomiya ◽  
S. Katayama ◽  
D. Filipescu ◽  
S. Belyshev ◽  
...  
Keyword(s):  
Cross Section ◽  
Neutron Multiplicity ◽  
New Method

scholarly journals The Power Losses in Cable Lines Supplying Nonlinear Loads

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1374
Author(s):  
Bartosz Rozegnał ◽  
Paweł Albrechtowicz ◽  
Dominik Mamcarz ◽  
Monika Rerak ◽  
Maciej Skaza
Keyword(s):  
Bessel Function ◽  
Cross Section ◽  
Power Loss ◽  
Sine Wave ◽  
Active Power ◽  
New Method ◽  
Power Losses ◽  
Nonlinear Loads ◽  
Current Harmonics ◽  
Cable Lines

This paper presents the skin effect impact on the active power losses in the sheathless single-core cables/wires supplying nonlinear loads. There are significant conductor losses when the current has a distorted waveform (e.g., the current supplying diode rectifiers). The authors present a new method for active power loss calculation. The obtained results have been compared to the IEC-60287-1-1:2006 + A1:2014 standard method and the method based on the Bessel function. For all methods, the active power loss results were convergent for small-cable cross-section areas. The proposed method gives smaller power loss values for these cable sizes than the IEC and Bessel function methods. For cable cross-section areas greater than 185 mm2, the obtained results were better than those for the other methods. There were also analyses of extra power losses for distorted currents compared to an ideal 50 Hz sine wave for all methods. The new method is based on the current penetration depth factor calculated for every considered current harmonics, which allows us to calculate the precise equivalent resistance for any cable size. This research is part of our work on a cable thermal analysis method that has been developed.

A new method for prediction of the acoustic performance and design parameter sensitivity analysis of multi-chamber perforated resonators with an irregular cross-section

2021 ◽  
pp. 1-24
Author(s):  
Rong Guo ◽  
Zanzan Sun ◽  
Zhen Huang ◽  
Rui Luo
Keyword(s):  
Theoretical Prediction ◽  
Cross Section ◽  
Flow Rate ◽  
New Method ◽  
Frequency Noise ◽  
Acoustic Characteristics ◽  
Inlet Flow ◽  
Acoustic Performance ◽  
Inlet Flow Rate ◽  
Prediction Approach

Abstract Aiming at reducing the high-amplitude and wide-frequency noise in charged air intake system of the powertrain, this paper proposes a new method for predicting the acoustic characteristics of an irregular cross-section multi-chamber perforated resonator under flow conditions. By this method, the presence of three-dimensional sound waves and the effects of higher-order modes are considered, and the acoustic performance of the resonator can be evaluated through the computation of transmission loss. Moreover, by discretizing the cross-section of perforated resonator and extracting node information, this method can solve the acoustic characteristics of the perforated resonator with any cross-section. Based on the transfer matrix method, the quadrupole parameters of each chamber are obtained. Then the acoustic characteristics of the multi-chamber perforated resonator could be calculated. The theoretical prediction data and the experimental data have been compared and the results show good agreement within the entire frequency range, which verifies the accuracy of the theoretical prediction approach. Based on this prediction approach, the influence of section ratio, structure parameters and inlet flow rate on the acoustic characteristics of the resonator is explored. The results show that when the structural parameters change, the peak resonance frequency of the resonator will have a regular shift. With the increase of the inlet flow rate, the main frequency band of sound attenuation will decrease significantly. The theoretical method developed in this work can be used for the calculation and optimization of multi-chamber resonators in various applications.

Deflection of Beams of Varying Cross Section

1937 ◽  
Vol 4 (2) ◽  
pp. A49-A52
Author(s):  
Miklós Hetényi
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Original Problem ◽  
New Method ◽  
Constant Cross Section ◽  
Deflection Curve ◽  
Force System ◽  
Uniform Cross Section ◽  
The Cross

Abstract This paper calls attention to a new method of dealing with deflections of beams, the cross sections of which vary by steps. It is shown that the effect of this variation on the shape of the deflection curve can be represented by a properly chosen force system acting on a beam of uniform cross section. There is no approximation involved in this substitution, whereby the original problem is reduced to one of computing deflections of beams of constant cross section.

Finite element simulation on the relationship between pressure and displacement for the waist of elastic pantyhose

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Rui Dan ◽  
Zhen Shi
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Research Work ◽  
Lumbar Vertebrae ◽  
Objective Evaluation ◽  
Quadratic Equation ◽  
New Method ◽  
Content Type ◽  
Displacement Distribution ◽  
The Relationship

PurposeObjective appraisal of pressure comfort is the key point of optimal designing of clothing. The purpose of this paper is to study a new method to provide pressure comfort for the waist of elastic pantyhose through the relationship between pressure and displacement using the finite element method (FEM).Design/methodology/approachThis paper presented a simulation model of the waist cross section consisting of three parts, namely skin, soft tissue and lumbar vertebrae, respectively, according to CT scan. The finite element the model of waist cross-section was established using Mimics software. The pressure–displacement quadratic equation can be obtained using ANSYS software and fitting curves. Meanwhile, we divide the waist cross-section into 12 equal regions according to angle, and then the area shrinkage mass of the waist cross-section can be calculated, respectively.FindingsIn this research work, we got the displacement distribution trend of elastic pantyhose at the waist cross section according to the area shrinkage mass of 12 regions, and this displacement could be used as an objective evaluation index for pressure comfort. All these solutions supply a theoretical reference for optimal design of the women's elastic pantyhose.Originality/valueThe paper analyzed the relationship between pressure and displacement for the waist of elastic pantyhose using FEM, and then got the displacement distribution trend of elastic pantyhose at the waist cross section according to the area shrinkage mass of different regions. It can supply a new method to appraise pressure comfort.

Sign in / Sign up

Export Citation Format

Share Document