scholarly journals Direct extraction of electron parameters from magnetoconductance analysis in mesoscopic ring array structures

2018 ◽  
Vol 97 (19) ◽  
Author(s):  
A. Sawada ◽  
S. Faniel ◽  
S. Mineshige ◽  
S. Kawabata ◽  
K. Saito ◽  
...  
Keyword(s):  
Direct Extraction ◽  
Array Structures ◽  
Mesoscopic Ring

Metabolomic studies of Piperaceae species: a correlation between miniaturization and direct extraction strategies

Planta Medica ◽  
2016 ◽  
Vol 81 (S 01) ◽  
pp. S1-S381
Author(s):  
AA Souza Júnior ◽  
LL Zanin ◽  
I Castro-Gamboa ◽  
M Furlan
Keyword(s):  
Direct Extraction

OBTAINING CHITIN FROM THE BLACK SOLDIER FLY HERMETIA ILLUCENS BY DIRECT EXTRACTION

2018 ◽  
Vol 2 (3) ◽  
pp. 84-87 ◽  
Author(s):  
A.S. Khayrova ◽  
◽  
S.A. Lopatin ◽  
O.A. Sinitsyna ◽  
A.P. Sinitsyn ◽  
...  
Keyword(s):  
Direct Extraction ◽  
Black Soldier Fly ◽  
Hermetia Illucens

scholarly journals A Toolbox for the Determination of Nitroaromatic Explosives in Marine Water, Sediment, and Biota Samples on Femtogram Levels by GC-MS/MS

Toxics ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 60
Author(s):  
Tobias Hartwig Bünning ◽  
Jennifer Susanne Strehse ◽  
Ann Christin Hollmann ◽  
Tom Bötticher ◽  
Edmund Maser
Keyword(s):  
Sample Preparation ◽  
Freeze Drying ◽  
Solid Phase ◽  
Phase Extraction ◽  
Direct Extraction ◽  
Time Saving ◽  
Marine Samples ◽  
Volume Method ◽  
Biota Samples

To determine the amount of the explosives 1,3-dinitrobenzene, 2,4-dinitrotoluene, 2,4,6-trinitrotoluene, and its metabolites in marine samples, a toolbox of methods was developed to enhance sample preparation and analysis of various types of marine samples, such as water, sediment, and different kinds of biota. To achieve this, established methods were adapted, improved, and combined. As a result, if explosive concentrations in sediment or mussel samples are greater than 10 ng per g, direct extraction allows for time-saving sample preparation; if concentrations are below 10 ng per g, techniques such as freeze-drying, ultrasonic, and solid-phase extraction can help to detect even picogram amounts. Two different GC-MS/MS methods were developed to enable the detection of these explosives in femtogram per microliter. With a splitless injector, limits of detection (LODs) between 77 and 333 fg/µL could be achieved in only 6.25 min. With the 5 µL programmable temperature vaporization—large volume method (PTV-LVI), LODs between 8 and 47 fg/µL could be achieved in less than 7 min. The detection limits achieved by these methods are among the lowest published to date. Their reliability has been tested and confirmed by measuring large and diverse sample sets.

scholarly journals Full snapshot reconstruction in hybrid architecture antenna arrays

2020 ◽  
Vol 2020 (1) ◽  
Author(s):  
Maria Trigka ◽  
Christos Mavrokefalidis ◽  
Kostas Berberidis
Keyword(s):  
Antenna Array ◽  
Antenna Arrays ◽  
Communication Systems ◽  
Linear Array ◽  
Research Work ◽  
Hybrid Architecture ◽  
Angle Of Arrival ◽  
Music Algorithm ◽  
Array Structures ◽  
Signal Sources

AbstractIn the context of this research work, we study the so-called problem of full snapshot reconstruction in hybrid antenna array structures that are utilized in mmWave communication systems. It enables the recovery of the snapshots that would have been obtained if a conventional (non-hybrid) uniform linear antenna array was employed. The problem is considered at the receiver side where the hybrid architecture exploits in a novel way the antenna elements of a uniform linear array. To this end, the recommended scheme is properly designed so as to be applicable to overlapping and non-overlapping architectures. Moreover, the full snapshot recoverability is addressed for two cases, namely for time-varying and constant signal sources. Simulation results are also presented to illustrate the consistency between the theoretically predicted behaviors and the simulated results, and the performance of the proposed scheme in terms angle-of-arrival estimation, when compared to the conventional MUSIC algorithm and a recently proposed hybrid version of MUSIC (H-MUSIC).

scholarly journals Fabrication and characterization of resistive double square loop arrays for ultra-wide bandwidth microwave absorption

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ji-Young Jeong ◽  
Je-Ryung Lee ◽  
Hyeonjin Park ◽  
Joonkyo Jung ◽  
Doo-Sun Choi ◽  
...  
Keyword(s):  
Sheet Resistance ◽  
Manufacturing Process ◽  
End Milling ◽  
Milling Process ◽  
Wide Bandwidth ◽  
Machined Surface ◽  
Array Pattern ◽  
Micro End Milling ◽  
Array Structures ◽  
Printing Processes

AbstractMicrowave absorbers using conductive ink are generally fabricated by printing an array pattern on a substrate to generate electromagnetic fields. However, screen printing processes are difficult to vary the sheet resistance values for different regions of the pattern on the same layer, because the printing process deposits materials at the same height over the entire surface of substrate. In this study, a promising manufacturing process was suggested for engraved resistive double square loop arrays with ultra-wide bandwidth microwave. The developed manufacturing process consists of a micro-end-milling, inking, and planing processes. A 144-number of double square loop array was precisely machined on a polymethyl methacrylate workpiece with the micro-end-milling process. After engraving array structures, the machined surface was completely covered with the developed conductive carbon ink with a sheet resistance of 15 Ω/sq. It was cured at room temperature. Excluding the ink that filled the machined double square loop array, overflowed ink was removed with the planing process to achieve full filled and isolated resistive array patterns. The fabricated microwave absorber showed a small radar cross-section with reflectance less than − 10 dB in the frequency band range of 8.0–14.6 GHz.

Sign in / Sign up

Export Citation Format

Share Document