scholarly journals BilayerSnS2: Tunable stacking sequence by charging and loading pressure

2016 ◽  
Vol 93 (12) ◽  
Author(s):  
C. Bacaksiz ◽  
S. Cahangirov ◽  
A. Rubio ◽  
R. T. Senger ◽  
F. M. Peeters ◽  
...  
Keyword(s):  
Stacking Sequence

High Resolution Study of Polytypism: Application to SiC and Au3 Mn

1982 ◽  
Vol 40 ◽  
pp. 540-541
Author(s):  
G. Van Tendeloo ◽  
J. Van Landuyt ◽  
S. Amelinckx
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Stacking Sequence ◽  
X Ray ◽  
Powerful Technique ◽  
Resolution Study ◽  
The Ideal

Polytypism has been studied for a number of years and a wide variety of stacking sequences has been detected and analysed. SiC is the prototype material in this respect; see e.g. Electron microscopy under high resolution conditions when combined with x-ray measurements is a very powerful technique to elucidate the correct stacking sequence or to study polytype transformations and deviations from the ideal stacking sequence.

Defect structures of Nb1+αS2 sulfidation scales

1992 ◽  
Vol 50 (1) ◽  
pp. 38-39
Author(s):  
Chuxin Zhou ◽  
L. W. Hobbs
Keyword(s):  
Stacking Faults ◽  
Rhombohedral Structure ◽  
Stacking Sequence ◽  
Defect Structures ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plane Normal ◽  
Lower Case ◽  
Sulfur Layer ◽  
Two Phases

One of the major purposes in the present work is to study the high temperature sulfidation properties of Nb in severe sulfidizing environments. Kinetically, the sulfidation rate of Nb is satisfactorily slow, but the microstructures and non-stoichiometry of Nb1+αS2 challenge conventional oxidation/sulfidation theory and defect models of non-stoichiometric compounds. This challenge reflects our limited knowledge of the dependence of kinetics and atomic migration processes in solid state materials on their defect structures.Figure 1 shows a high resolution image of a platelet from the middle portion of the Nb1+αS2 scale. A thin lamellar heterogeneity (about 5nm) is observed. From X-ray diffraction results, we have shown that Nb1+αS2 scale is principally rhombohedral structure, but 2H-NbS2 can result locally due to stacking faults, because the only difference between these 2H and 3R phases is variation in the stacking sequence along the c axis. Following an ABC notation, we use capital letters A, B and C to represent the sulfur layer, and lower case letters a, b and c to refer to Nb layers. For example, the stacking sequence of 2H phase is AbACbCA, which is a ∼12Å period along the c axis; the stacking sequence of 3R phase is AbABcBCaCA to form an ∼18Å period along the c axis. Intergrowth of these two phases can take place at stacking faults or by a shear in the basal plane normal to the c axis.

Stacking Sequence Dispersion for Improved Damage Tolerance

2008 ◽  
Author(s):  
Claudio Lopes ◽  
Pedro Camanho ◽  
Zafer Gurdal ◽  
Omprakash Seresta ◽  
Pere Maimi
Keyword(s):  
Damage Tolerance ◽  
Stacking Sequence

scholarly journals Enhanced Impact Properties of Hybrid Composites Reinforced by Carbon Fiber and Polyimide Fiber

Polymers ◽  
2021 ◽  
Vol 13 (16) ◽  
pp. 2599
Author(s):  
Boyao Wang ◽  
Bin He ◽  
Zhanwen Wang ◽  
Shengli Qi ◽  
Daijun Zhang ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Failure Modes ◽  
Flexural Modulus ◽  
Charpy Impact ◽  
Fiber Reinforced Composites ◽  
Stacking Sequence ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Hybrid Fiber ◽  
Polyimide Fiber

A series of hybrid fiber-reinforced composites were prepared with polyimide fiber and carbon fiber as the reinforcement and epoxy resin as the matrix. The influence of stacking sequence on the Charpy impact and flexural properties of the composites as well as the failure modes were studied. The results showed that hybrid fiber-reinforced composites yielded nearly 50% increment in Charpy impact strength compared with the ones reinforced by carbon fiber. The flexural performance was significantly improved compared with those reinforced solely by polyimide fibers and was greatly affected by the stacking sequence. The specimens with compressive sides distributed with carbon fiber possessed higher flexural strength, while those holding a sandwich-like structure with carbon fiber filling between the outer layers displayed a higher flexural modulus.

scholarly journals Experimental and Numerical Buckling Analyses of Laminated Composite Plates under Temperature Effects

2010 ◽  
Vol 19 (4) ◽  
pp. 096369351001900 ◽  
Author(s):  
Emin Ergun
Keyword(s):  
Composite Plate ◽  
Numerical Solutions ◽  
Laminated Composite ◽  
Composite Plates ◽  
Buckling Load ◽  
Fibre Reinforcement ◽  
Stacking Sequence ◽  
Laminated Composite Plates ◽  
Different Temperatures ◽  
Good Agreement

The aim of this study is to investigate, experimentally and numerically, the change of critical buckling load in composite plates with different ply numbers, orientation angles, stacking sequences and boundary conditions as a function of temperature. Buckling specimens have been removed from the composite plate with glass-fibre reinforcement at [0°]i and [45°]i (i= number of ply). First, the mechanical properties of the composite material were determined at different temperatures, and after that, buckling experiments were done for those temperatures. Then, numerical solutions were obtained by modelling the specimens used in the experiment in the Ansys10 finite elements package software. The experimental and numerical results are in very good agreement with each other. It was found that the values of the buckling load at [0°] on the composite plates are higher than those of other angles. Besides, symmetrical and anti-symmetrical conditions were examined to see the effect of the stacking sequence on buckling and only numerical solutions were obtained. It is seen that the buckling load reaches the highest value when it is symmetrical in the cross-ply stacking sequence and it is anti-symmetrical in the angle-ply stacking sequence.

ChemInform Abstract: 3s-Gd2C2Br2, an Isomorph with a New Stacking Sequence

ChemInform ◽  
2010 ◽  
Vol 23 (27) ◽  
pp. no-no
Author(s):  
HJ. MATTAUSCH ◽  
R. K. KREMER ◽  
R. EGER ◽  
A. SIMON
Keyword(s):  
Stacking Sequence
Sign in / Sign up

Export Citation Format

Share Document