Stress-strain curves of aluminum nanowires: Fluctuations in the plastic regime and absence of hardening

2008 ◽  
Vol 78 (15) ◽  
Author(s):  
L. Pastor-Abia ◽  
M. J. Caturla ◽  
E. SanFabián ◽  
G. Chiappe ◽  
E. Louis
Keyword(s):  
Stress Strain ◽  
Plastic Regime

Elastic to elastic–plastic transition of Al2O3/TiC ceramics studied by nanoindentation

2009 ◽  
Vol 24 (6) ◽  
pp. 1960-1966 ◽  
Author(s):  
Katrin Zimmermann ◽  
Gerold A. Schneider
Keyword(s):  
Work Load ◽  
Stress Strain ◽  
Elastic Plastic ◽  
Conventional Analysis ◽  
Alumina Phase ◽  
Plastic Regime ◽  
Cube Corner ◽  
Mixed Ceramic ◽  
Penetration Depths

In this work load–penetration curves obtained by nanoindentation were analyzed, using a spherical tip approximation and applying the stress/strain concept by Tabor. Nanoindentation experiments were done on sapphire, pure TiC, and a mixed ceramic with in situ formed TiCx layer, using a sharp cube-corner indenter at very low loads and penetration depths. With the implemented method it is possible to display the elastic to elastic–plastic transition of each investigated phase, and much more information can be extracted than by conventional analysis. Regarding the mixed ceramic, it was found that the present TiC phases exhibit slightly lower hardness than the alumina phase, but they can sustain much higher stresses during the transition from the elastic to the elastic–plastic regime. This is considered to be beneficial for the application as cutting material. No correlation was found between the nanomechanical behavior of the model materials sapphire and TiC and the corresponding phases of the mixed ceramic.

Effect of deformation rate on the stress-strain curves of gelatin gels

1996 ◽  
Vol 93 ◽  
pp. 837-849 ◽  
Author(s):  
A Bot ◽  
IA van Amerongen ◽  
RD Groot ◽  
NL Hoekstra ◽  
WGM Agterof
Keyword(s):  
Deformation Rate ◽  
Stress Strain ◽  
Gelatin Gels

КОНСТРУКТИВНО-ТЕХНОЛОГІЧНІ ОСОБЛИВОСТІ ХВОСТО-ВИХ БАЛОК СІТЧАСТОГО ТИПУ З ПОЛІМЕРНИХ КОМПО-ЗИЦІЙНИХ МАТЕРІАЛІВ ВЕРТОЛЬОТІВ ТРАНСПОРТНОЇ КАТЕГОРІЇ

2020 ◽  
pp. 15-30
Author(s):  
А. Г. Гребеников ◽  
И. В. Малков ◽  
В. А. Урбанович ◽  
Н. И. Москаленко ◽  
Д. С. Колодийчик
Keyword(s):  
Finite Element ◽  
Strain State ◽  
Layer Structure ◽  
Metal Structure ◽  
Element Model ◽  
Stress Strain ◽  
Element Analysis ◽  
Mesh Structure ◽  
Stress Strain State ◽  
Mesh Structures

The analysis of the design and technological features of the tail boom (ТB) of a helicopter made of polymer composite materials (PCM) is carried out.Three structural and technological concepts are distinguished - semi-monocoque (reinforced metal structure), monocoque (three-layer structure) and mesh-type structure. The high weight and economic efficiency of mesh structures is shown, which allows them to be used in aerospace engineering. The physicomechanical characteristics of the network structures are estimated and their uniqueness is shown. The use of mesh structures can reduce the weight of the product by a factor of two or more.The stress-strain state (SSS) of the proposed tail boom design is determined. The analysis of methods for calculating the characteristics of the total SSS of conical mesh shells is carried out. The design of the tail boom is presented, the design diagram of the tail boom of the transport category rotorcraft is developed. A finite element model was created using the Siemens NX 7.5 system. The calculation of the stress-strain state (SSS) of the HC of the helicopter was carried out on the basis of the developed structural scheme using the Advanced Simulation module of the Siemens NX 7.5 system. The main zones of probable fatigue failure of tail booms are determined. Finite Element Analysis (FEA) provides a theoretical basis for design decisions.Shown is the effect of the type of technological process selected for the production of the tail boom on the strength of the HB structure. The stability of the characteristics of the PCM tail boom largely depends on the extent to which its design is suitable for the use of mechanized and automated production processes.A method for the manufacture of a helicopter tail boom from PCM by the automated winding method is proposed. A variant of computer modeling of the tail boom of a mesh structure made of PCM is shown.The automated winding technology can be recommended for implementation in the design of the composite tail boom of the Mi-2 and Mi-8 helicopters.

Delamination in the scoring and folding of paperboard

TAPPI Journal ◽  
2012 ◽  
Vol 11 (1) ◽  
pp. 61-66 ◽  
Author(s):  
DOEUNG D. CHOI ◽  
SERGIY A. LAVRYKOV ◽  
BANDARU V. RAMARAO
Keyword(s):  
Finite Element ◽  
Plane Deformation ◽  
Strain Analysis ◽  
Local Strain ◽  
Uniaxial Stress ◽  
Material Model ◽  
Element Model ◽  
Plastic Behavior ◽  
Stress Strain ◽  
Strain Fields

Delamination between layers occurs during the creasing and subsequent folding of paperboard. Delamination is necessary to provide some stiffness properties, but excessive or uncontrolled delamination can weaken the fold, and therefore needs to be controlled. An understanding of the mechanics of delamination is predicated upon the availability of reliable and properly calibrated simulation tools to predict experimental observations. This paper describes a finite element simulation of paper mechanics applied to the scoring and folding of multi-ply carton board. Our goal was to provide an understanding of the mechanics of these operations and the proper models of elastic and plastic behavior of the material that enable us to simulate the deformation and delamination behavior. Our material model accounted for plasticity and sheet anisotropy in the in-plane and z-direction (ZD) dimensions. We used different ZD stress-strain curves during loading and unloading. Material parameters for in-plane deformation were obtained by fitting uniaxial stress-strain data to Ramberg-Osgood plasticity models and the ZD deformation was modeled using a modified power law. Two-dimensional strain fields resulting from loading board typical of a scoring operation were calculated. The strain field was symmetric in the initial stages, but increasing deformation led to asymmetry and heterogeneity. These regions were precursors to delamination and failure. Delamination of the layers occurred in regions of significant shear strain and resulted primarily from the development of large plastic strains. The model predictions were confirmed by experimental observation of the local strain fields using visual microscopy and linear image strain analysis. The finite element model predicted sheet delamination matching the patterns and effects that were observed in experiments.

Sign in / Sign up

Export Citation Format

Share Document