scholarly journals Bulk anyons as edge symmetries: Boundary phase diagrams of topologically ordered states

2021 ◽  
Vol 104 (7) ◽  
Author(s):  
Tsuf Lichtman ◽  
Ryan Thorngren ◽  
Netanel H. Lindner ◽  
Ady Stern ◽  
Erez Berg
Keyword(s):  
Phase Diagrams ◽  
Boundary Phase

Grain boundary phase transitions and phase diagrams

2001 ◽  
Vol 3 (8) ◽  
pp. 1113-1115 ◽  
Author(s):  
B.B Straumal ◽  
P Ziȩba ◽  
W Gust
Keyword(s):  
Phase Transitions ◽  
Grain Boundary ◽  
Phase Diagrams ◽  
Boundary Phase

Transmission electron microscope studies in special ceramics

1978 ◽  
Vol 36 (1) ◽  
pp. 268-269
Author(s):  
A. Zangvil ◽  
L.J. Gauckler ◽  
G. Schneider ◽  
M. Rühle
Keyword(s):  
Phase Diagrams ◽  
Crystal Structures ◽  
Thin Foil ◽  
Limited Extent ◽  
Complex Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Electron Microscopes ◽  
Lattice Resolution

The use of high temperature special ceramics which are usually complex materials based on oxides, nitrides, carbides and borides of silicon and aluminum, is critically dependent on their thermomechanical and other physical properties. The investigations of the phase diagrams, crystal structures and microstructural features are essential for better understanding of the macro-properties. Phase diagrams and crystal structures have been studied mainly by X-ray diffraction (XRD). Transmission electron microscopy (TEM) has contributed to this field to a very limited extent; it has been used more extensively in the study of microstructure, phase transformations and lattice defects. Often only TEM can give solutions to numerous problems in the above fields, since the various phases exist in extremely fine grains and subgrain structures; single crystals of appreciable size are often not available. Examples with some of our experimental results from two multicomponent systems are presented here. The standard ion thinning technique was used for the preparation of thin foil samples, which were then investigated with JEOL 200A and Siemens ELMISKOP 102 (for the lattice resolution work) electron microscopes.

Examination of Fracture Interfaces in Silicon Nitride

1975 ◽  
Vol 33 ◽  
pp. 60-61
Author(s):  
Nancy J. Tighe
Keyword(s):  
Silicon Nitride ◽  
Grain Boundary ◽  
Crack Growth ◽  
Subcritical Crack Growth ◽  
Slow Crack Growth ◽  
Ceramic Materials ◽  
Grain Boundary Sliding ◽  
Boundary Phase ◽  
Turbine Engines ◽  
Boundary Sliding

Silicon nitride is one of the ceramic materials being considered for the components in gas turbine engines which will be exposed to temperatures of 1000 to 1400°C. Test specimens from hot-pressed billets exhibit flexural strengths of approximately 50 MN/m2 at 1000°C. However, the strength degrades rapidly to less than 20 MN/m2 at 1400°C. The strength degradition is attributed to subcritical crack growth phenomena evidenced by a stress rate dependence of the flexural strength and the stress intensity factor. This phenomena is termed slow crack growth and is associated with the onset of plastic deformation at the crack tip. Lange attributed the subcritical crack growth tb a glassy silicate grain boundary phase which decreased in viscosity with increased temperature and permitted a form of grain boundary sliding to occur.

Characterization of intergranular cuprous oxide in polycrystalline YBa2Cu3O7-x

1988 ◽  
Vol 46 ◽  
pp. 880-881
Author(s):  
Bradley L. Thiel ◽  
Chan Han R. P. ◽  
Kurosky L. C. Hutter ◽  
I. A. Aksay ◽  
Mehmet Sarikaya
Keyword(s):  
Grain Boundary ◽  
Cuprous Oxide ◽  
Room Temperature ◽  
Boundary Phase ◽  
Spectroscopic Techniques ◽  
Transition Width ◽  
Practical Applications ◽  
Thin Foils ◽  
Superconducting Oxides

The identification of extraneous phases is important in understanding of high Tc superconducting oxides. The spectroscopic techniques commonly used in determining the origin of superconductivity (such as RAMAN, XPS, AES, and EXAFS) are surface-sensitive. Hence a grain boundary phase several nanometers thick could produce irrelevant spectroscopic results and cause erroneous conclusions. The intergranular phases present a major technological consideration for practical applications. In this communication we report the identification of a Cu2O grain boundary phase which forms during the sintering of YBa2Cu3O7-x (1:2:3 compound).Samples are prepared using a mixture of Y2O3. CuO, and BaO2 powders dispersed in ethanol for complete mixing. The pellets pressed at 20,000 psi are heated to 950°C at a rate of 5°C per min, held for 1 hr, and cooled at 1°C per min to room temperature. The samples show a Tc of 91K with a transition width of 2K. In order to prevent damage, a low temperature stage is used in milling to prepare thin foils which are then observed, using a liquid nitrogen holder, in a Philips 430T at 300 kV.

Effect of furnace atmosphere and silica content on the consolidation behaviour of magnesia partially stabilised zirconia

1990 ◽  
Vol 48 (4) ◽  
pp. 1056-1057
Author(s):  
J. Drennan ◽  
R.H.J. Hannink ◽  
D.R. Clarke ◽  
T.M. Shaw
Keyword(s):  
Liquid Phase ◽  
Silica Content ◽  
Liquid Phase Sintering ◽  
Furnace Atmosphere ◽  
Boundary Phase ◽  
Analytical Electron ◽  
Analytical Electron Microscope ◽  
Series Of Experiments ◽  
Compositional Gradients ◽  
Mobile Liquid

Magnesia partially stabilised zirconia (Mg-PSZ) ceramics are renowned for their excellent nechanical properties. These are effected by processing conditions and purity of starting materials. It has been previously shown that small additions of strontia (SrO) have the effect of removing the major contaminant, silica (SiO2).The mechanism by which this occurs is not fully understood but the strontia appears to form a very mobile liquid phase at the grain boundaries. As the sintering reaches the final stages the liquid phase is expelled to the surface of the ceramic. A series of experiments, to examine the behaviour of the liquid grain boundary phase, were designed to produce compositional gradients across the ceramic bodies. To achieve this, changes in both silica content and furnace atmosphere were implemented. Analytical electron microscope techniques were used to monitor the form and composition of the phases developed. This paper describes the results of our investigation and the presentation will discuss the work with reference to liquid phase sintering of ceramics in general.

Sign in / Sign up

Export Citation Format

Share Document