Unimportance of Surface Roughness Upon the Kapitza Resistance

1961 ◽  
Vol 123 (6) ◽  
pp. 1909-1911 ◽  
Author(s):  
W. A. Little
Keyword(s):  
Surface Roughness ◽  
Kapitza Resistance

EFFECT OF SURFACE ROUGHNESS ON THE KAPITZA RESISTANCE

1981 ◽  
Vol 42 (C6) ◽  
pp. C6-819-C6-821
Author(s):  
T. J. Shen ◽  
D. Castiel ◽  
A. A. Maradudin
Keyword(s):  
Surface Roughness ◽  
Kapitza Resistance ◽  
Effect Of Surface

Roughness measurements of nonlinear optical polymer films by scanning tunneling microscopy

1989 ◽  
Vol 47 ◽  
pp. 22-23
Author(s):  
I. H. Musselman ◽  
R.-T. Chen ◽  
P. E. Russell
Keyword(s):  
Surface Roughness ◽  
Scanning Tunneling Microscopy ◽  
Nonlinear Optical ◽  
Polymer Surface ◽  
Light Extinction ◽  
Scanning Tunneling ◽  
Silicon Substrates ◽  
Tunneling Microscopy ◽  
Optical Polymer ◽  
Total Light

Scanning tunneling microscopy (STM) has been used to characterize the surface roughness of nonlinear optical (NLO) polymers. A review of STM of polymer surfaces is included in this volume. The NLO polymers are instrumental in the development of electrooptical waveguide devices, the most fundamental of which is the modulator. The most common modulator design is the Mach Zehnder interferometer, in which the input light is split into two legs and then recombined into a common output within the two dimensional waveguide. A π phase retardation, resulting in total light extinction at the output of the interferometer, can be achieved by changing the refractive index of one leg with respect to the other using the electrooptic effect. For best device performance, it is essential that the NLO polymer exhibit minimal surface roughness in order to reduce light scattering. Scanning tunneling microscopy, with its high lateral and vertical resolution, is capable of quantifying the NLO polymer surface roughness induced by processing. Results are presented below in which STM was used to measure the surface roughness of films produced by spin-coating NLO-active polymers onto silicon substrates.

Surface roughness measurements of vanadium-contaminated fluidized cracking catalysts by atomic force microscopy

1996 ◽  
Vol 54 ◽  
pp. 866-867
Author(s):  
H. Kinney ◽  
M.L. Occelli ◽  
S.A.C. Gould
Keyword(s):  
Surface Roughness ◽  
Zeolite Y ◽  
Atomic Level ◽  
Microporous Structure ◽  
Contact Mode ◽  
Force Microscopy ◽  
Atomic Force ◽  
Before And After ◽  
Roughness Measurements ◽  
Cracking Catalysts

For this study we have used a contact mode atomic force microscope (AFM) to study to topography of fluidized cracking catalysts (FCC), before and after contamination with 5% vanadium. We selected the AFM because of its ability to well characterize the surface roughness of materials down to the atomic level. It is believed that the cracking in the FCCs occurs mainly on the catalysts top 10-15 μm suggesting that the surface corrugation could play a key role in the FCCs microactivity properties. To test this hypothesis, we chose vanadium as a contaminate because this metal is capable of irreversibly destroying the FCC crystallinity as well as it microporous structure. In addition, we wanted to examine the extent to which steaming affects the vanadium contaminated FCC. Using the AFM, we measured the surface roughness of FCCs, before and after contamination and after steaming.We obtained our FCC (GRZ-1) from Davison. The FCC is generated so that it contains and estimated 35% rare earth exchaged zeolite Y, 50% kaolin and 15% binder.

KAPITZA RESISTANCE BETWEEN CMN AND 3He AROUND THE mK

1978 ◽  
Vol 39 (C6) ◽  
pp. C6-262-C6-264 ◽  
Author(s):  
B. Hebral ◽  
G. Frossati ◽  
H. Godfrin ◽  
G. Schumacher ◽  
D. Thoulouze
Keyword(s):  
Kapitza Resistance
Sign in / Sign up

Export Citation Format

Share Document