scholarly journals Contact patch memory of tyres leading to lateral vibrations of four-wheeled vehicles

2013 ◽  
Vol 371 (1993) ◽  
pp. 20120427 ◽  
Author(s):  
Dénes Takács ◽  
Gábor Stépán
Keyword(s):  
Large Scale ◽  
Multiple Scales ◽  
Travelling Wave ◽  
Small Scale ◽  
Global Dynamics ◽  
Contact Patch ◽  
Lateral Vibrations ◽  
Wide Range ◽  
The Stability ◽  
Wheeled Vehicles

It has been shown recently that the shimmy motion of towed wheels can be predicted in a wide range of parameters by means of the so-called memory effect of tyres. This delay effect is related to the existence of a travelling-wave-like motion of the tyre points in contact with the ground relative to the wheel. This study shows that the dynamics within the small-scale contact patch can have an essential effect on the global dynamics of a four-wheeled automobile on a large scale. The stability charts identify narrow parameter regions of increased fuel consumption and tyre noise with the help of the delay models that are effective tools in dynamical problems through multiple scales.

Drift, Stabilization and Destabilization of Patlak-Keller-Seegel Systems Due to a Short-Wave External Signal

2020 ◽  
pp. 36-48
Author(s):  
Andrey B. Morgulis ◽  
Konstantin I. Ilin
Keyword(s):  
Large Scale ◽  
Short Wave ◽  
Travelling Wave ◽  
Small Scale ◽  
External Signal ◽  
Environmental Fluctuations ◽  
The Stability ◽  
Homogeneous Environment

In this article, we explore a community of two species placed on the inhomogeneous environment. We assume interspecific taxis as well as responding to the environmental fluctuations by tactic movement. We study the effect of the small-scale environmental fluctuations on the large-scale dynamics of the community following the line of Kapitza's theory of the upside-down pendulum. It turns out that, the only conductor of the effect of the fluctuations on the large-scale patterns is some drift of species. When the fluctuation takes the form of a travelling wave, there exist the quasi-equilibria, which are equilibria on average, roughly speaking. Examining the stability of the quasi-equilibria shows that, compared to the case of the homogeneous environment, increasing the magnitude of the fluctuations can destabilize the quasi-equilibria as well as stabilize them. It depends only on the speed at which the fluctuation wave prop-agates which of these effects occurs. Anyway, the effect is exponential in the amplitude of the wave.

scholarly journals No-z Model for Magnetic Fields of Different Astrophysical Objects and Stability of the Solutions

Data ◽  
2021 ◽  
Vol 6 (1) ◽  
pp. 4
Author(s):  
Evgeny Mikhailov ◽  
Daniela Boneva ◽  
Maria Pashentseva
Keyword(s):  
Magnetic Field ◽  
Magnetic Fields ◽  
Large Scale ◽  
Point Of View ◽  
Accretion Discs ◽  
Wide Range ◽  
Astrophysical Objects ◽  
Alpha Effect ◽  
The Stability ◽  
The Magnetic Field

A wide range of astrophysical objects, such as the Sun, galaxies, stars, planets, accretion discs etc., have large-scale magnetic fields. Their generation is often based on the dynamo mechanism, which is connected with joint action of the alpha-effect and differential rotation. They compete with the turbulent diffusion. If the dynamo is intensive enough, the magnetic field grows, else it decays. The magnetic field evolution is described by Steenbeck—Krause—Raedler equations, which are quite difficult to be solved. So, for different objects, specific two-dimensional models are used. As for thin discs (this shape corresponds to galaxies and accretion discs), usually, no-z approximation is used. Some of the partial derivatives are changed by the algebraic expressions, and the solenoidality condition is taken into account as well. The field generation is restricted by the equipartition value and saturates if the field becomes comparable with it. From the point of view of mathematical physics, they can be characterized as stable points of the equations. The field can come to these values monotonously or have oscillations. It depends on the type of the stability of these points, whether it is a node or focus. Here, we study the stability of such points and give examples for astrophysical applications.

Coupled Thermo-Hydro-Geochemical Models of Engineered Barrier Systems: The Febex Project

2000 ◽  
Vol 663 ◽  
Author(s):  
J. Samper ◽  
R. Juncosa ◽  
V. Navarro ◽  
J. Delgado ◽  
L. Montenegro ◽  
...  
Keyword(s):  
Large Scale ◽  
Reference Model ◽  
Numerical Models ◽  
Full Scale ◽  
Small Scale ◽  
Model Parameters ◽  
In Situ Test ◽  
Wide Range ◽  
Engineered Barrier

ABSTRACTFEBEX (Full-scale Engineered Barrier EXperiment) is a demonstration and research project dealing with the bentonite engineered barrier designed for sealing and containment of waste in a high level radioactive waste repository (HLWR). It includes two main experiments: an situ full-scale test performed at Grimsel (GTS) and a mock-up test operating since February 1997 at CIEMAT facilities in Madrid (Spain) [1,2,3]. One of the objectives of FEBEX is the development and testing of conceptual and numerical models for the thermal, hydrodynamic, and geochemical (THG) processes expected to take place in engineered clay barriers. A significant improvement in coupled THG modeling of the clay barrier has been achieved both in terms of a better understanding of THG processes and more sophisticated THG computer codes. The ability of these models to reproduce the observed THG patterns in a wide range of THG conditions enhances the confidence in their prediction capabilities. Numerical THG models of heating and hydration experiments performed on small-scale lab cells provide excellent results for temperatures, water inflow and final water content in the cells [3]. Calculated concentrations at the end of the experiments reproduce most of the patterns of measured data. In general, the fit of concentrations of dissolved species is better than that of exchanged cations. These models were later used to simulate the evolution of the large-scale experiments (in situ and mock-up). Some thermo-hydrodynamic hypotheses and bentonite parameters were slightly revised during TH calibration of the mock-up test. The results of the reference model reproduce simultaneously the observed water inflows and bentonite temperatures and relative humidities. Although the model is highly sensitive to one-at-a-time variations in model parameters, the possibility of parameter combinations leading to similar fits cannot be precluded. The TH model of the “in situ” test is based on the same bentonite TH parameters and assumptions as for the “mock-up” test. Granite parameters were slightly modified during the calibration process in order to reproduce the observed thermal and hydrodynamic evolution. The reference model captures properly relative humidities and temperatures in the bentonite [3]. It also reproduces the observed spatial distribution of water pressures and temperatures in the granite. Once calibrated the TH aspects of the model, predictions of the THG evolution of both tests were performed. Data from the dismantling of the in situ test, which is planned for the summer of 2001, will provide a unique opportunity to test and validate current THG models of the EBS.

Geomechanical and Fracture Network Interpretation of a Devonian Outcrop

2021 ◽  
pp. 1-16
Author(s):  
Scott McKean ◽  
Simon Poirier ◽  
Henry Galvis-Portilla ◽  
Marco Venieri ◽  
Jeffrey A. Priest ◽  
...  
Keyword(s):  
Large Scale ◽  
Multiple Scales ◽  
Fracture Network ◽  
Natural Fracture ◽  
Small Scale ◽  
Nugget Effect ◽  
Schmidt Hammer ◽  
Unconventional Reservoir ◽  
Fracture Anisotropy ◽  
Fracture Intensity

Summary The Duvernay Formation is an unconventional reservoir characterized by induced seismicity and fluid migration, with natural fractures likely contributing to both cases. An alpine outcrop of the Perdrix and Flume formations, correlative with the subsurface Duvernay and Waterways formations, was investigated to characterize natural fracture networks. A semiautomated image-segmentation and fracture analysis was applied to orthomosaics generated from a photogrammetric survey to assess small- and large-scale fracture intensity and rock mass heterogeneity. The study also included manual scanlines, fracture windows, and Schmidt hammer measurements. The Perdrix section transitions from brittle fractures to en echelon fractures and shear-damage zones. Multiple scales of fractures were observed, including unconfined, bedbound fractures, and fold-relatedbed-parallel partings (BPPs). Variograms indicate a significant nugget effect along with fracture anisotropy. Schmidt hammer results lack correlation with fracture intensity. The Flume pavements exhibit a regionally extensive perpendicular joint set, tectonically driven fracturing, and multiple fault-damage zones with subvertical fractures dominating. Similar to the Perdrix, variograms show a significant nugget effect, highlighting fracture anisotropy. The results from this study suggest that small-scale fractures are inherently stochastic and that fractures observed at core scale should not be extrapolated to represent large-scale fracture systems; instead, the effects of small-scale fractures are best represented using an effective continuum approach. In contrast, large-scale fractures are more predictable according to structural setting and should be characterized robustly using geological principles. This study is especially applicable for operators and regulators in the Duvernay and similar formations where unconventional reservoir units abut carbonate formations.

Buoyancy effects on large-scale motions in convective atmospheric boundary layers: implications for modulation of near-wall processes

2018 ◽  
Vol 856 ◽  
pp. 135-168 ◽  
Author(s):  
S. T. Salesky ◽  
W. Anderson
Keyword(s):  
Boundary Layer ◽  
Velocity Field ◽  
Boundary Layers ◽  
Vertical Velocity ◽  
Amplitude Modulation ◽  
Large Scale ◽  
Streamwise Velocity ◽  
Small Scale ◽  
Convective Conditions ◽  
Wide Range

A number of recent studies have demonstrated the existence of so-called large- and very-large-scale motions (LSM, VLSM) that occur in the logarithmic region of inertia-dominated wall-bounded turbulent flows. These regions exhibit significant streamwise coherence, and have been shown to modulate the amplitude and frequency of small-scale inner-layer fluctuations in smooth-wall turbulent boundary layers. In contrast, the extent to which analogous modulation occurs in inertia-dominated flows subjected to convective thermal stratification (low Richardson number) and Coriolis forcing (low Rossby number), has not been considered. And yet, these parameter values encompass a wide range of important environmental flows. In this article, we present evidence of amplitude modulation (AM) phenomena in the unstably stratified (i.e. convective) atmospheric boundary layer, and link changes in AM to changes in the topology of coherent structures with increasing instability. We perform a suite of large eddy simulations spanning weakly ($-z_{i}/L=3.1$) to highly convective ($-z_{i}/L=1082$) conditions (where$-z_{i}/L$is the bulk stability parameter formed from the boundary-layer depth$z_{i}$and the Obukhov length $L$) to investigate how AM is affected by buoyancy. Results demonstrate that as unstable stratification increases, the inclination angle of surface layer structures (as determined from the two-point correlation of streamwise velocity) increases from$\unicode[STIX]{x1D6FE}\approx 15^{\circ }$for weakly convective conditions to nearly vertical for highly convective conditions. As$-z_{i}/L$increases, LSMs in the streamwise velocity field transition from long, linear updrafts (or horizontal convective rolls) to open cellular patterns, analogous to turbulent Rayleigh–Bénard convection. These changes in the instantaneous velocity field are accompanied by a shift in the outer peak in the streamwise and vertical velocity spectra to smaller dimensionless wavelengths until the energy is concentrated at a single peak. The decoupling procedure proposed by Mathiset al.(J. Fluid Mech., vol. 628, 2009a, pp. 311–337) is used to investigate the extent to which amplitude modulation of small-scale turbulence occurs due to large-scale streamwise and vertical velocity fluctuations. As the spatial attributes of flow structures change from streamwise to vertically dominated, modulation by the large-scale streamwise velocity decreases monotonically. However, the modulating influence of the large-scale vertical velocity remains significant across the stability range considered. We report, finally, that amplitude modulation correlations are insensitive to the computational mesh resolution for flows forced by shear, buoyancy and Coriolis accelerations.

scholarly journals Self-Supervised Pre-Training of Transformers for Satellite Image Time Series Classification

2020 ◽  
Author(s):  
Yuan Yuan ◽  
Lei Lin
Keyword(s):  
Time Series ◽  
Deep Learning ◽  
Large Scale ◽  
Temporal Structure ◽  
Satellite Image ◽  
Fine Tuning ◽  
Small Scale ◽  
Model Parameters ◽  
Learning Approaches ◽  
Wide Range

Satellite image time series (SITS) classification is a major research topic in remote sensing and is relevant for a wide range of applications. Deep learning approaches have been commonly employed for SITS classification and have provided state-of-the-art performance. However, deep learning methods suffer from overfitting when labeled data is scarce. To address this problem, we propose a novel self-supervised pre-training scheme to initialize a Transformer-based network by utilizing large-scale unlabeled data. In detail, the model is asked to predict randomly contaminated observations given an entire time series of a pixel. The main idea of our proposal is to leverage the inherent temporal structure of satellite time series to learn general-purpose spectral-temporal representations related to land cover semantics. Once pre-training is completed, the pre-trained network can be further adapted to various SITS classification tasks by fine-tuning all the model parameters on small-scale task-related labeled data. In this way, the general knowledge and representations about SITS can be transferred to a label-scarce task, thereby improving the generalization performance of the model as well as reducing the risk of overfitting. Comprehensive experiments have been carried out on three benchmark datasets over large study areas. Experimental results demonstrate the effectiveness of the proposed method, leading to a classification accuracy increment up to 1.91% to 6.69%. <div><b>This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may no longer be accessible.</b></div>

scholarly journals Physical Transport Processes that Affect the Distribution of Oil in the Gulf of Mexico: Observations and Modeling

Oceanography ◽  
2021 ◽  
Vol 34 (1) ◽  
pp. 58-75
Author(s):  
Michel Boufadel ◽  
◽  
Annalisa Bracco ◽  
Eric Chassignet ◽  
Shuyi Chen ◽  
...  
Keyword(s):  
Gulf Of Mexico ◽  
Physical Environment ◽  
Large Scale ◽  
Transport Processes ◽  
Small Scale ◽  
Surface Mixed Layer ◽  
Physical Processes ◽  
Mixing Processes ◽  
Near Surface ◽  
Wide Range

Physical transport processes such as the circulation and mixing of waters largely determine the spatial distribution of materials in the ocean. They also establish the physical environment within which biogeochemical and other processes transform materials, including naturally occurring nutrients and human-made contaminants that may sustain or harm the region’s living resources. Thus, understanding and modeling the transport and distribution of materials provides a crucial substrate for determining the effects of biological, geological, and chemical processes. The wide range of scales in which these physical processes operate includes microscale droplets and bubbles; small-scale turbulence in buoyant plumes and the near-surface “mixed” layer; submesoscale fronts, convergent and divergent flows, and small eddies; larger mesoscale quasi-geostrophic eddies; and the overall large-scale circulation of the Gulf of Mexico and its interaction with the Atlantic Ocean and the Caribbean Sea; along with air-sea interaction on longer timescales. The circulation and mixing processes that operate near the Gulf of Mexico coasts, where most human activities occur, are strongly affected by wind- and river-induced currents and are further modified by the area’s complex topography. Gulf of Mexico physical processes are also characterized by strong linkages between coastal/shelf and deeper offshore waters that determine connectivity to the basin’s interior. This physical connectivity influences the transport of materials among different coastal areas within the Gulf of Mexico and can extend to adjacent basins. Major advances enabled by the Gulf of Mexico Research Initiative in the observation, understanding, and modeling of all of these aspects of the Gulf’s physical environment are summarized in this article, and key priorities for future work are also identified.

scholarly journals Dependence of Model Energy Spectra on Vertical Resolution

2016 ◽  
Vol 144 (4) ◽  
pp. 1407-1421 ◽  
Author(s):  
Michael L. Waite
Keyword(s):  
High Resolution ◽  
Large Scale ◽  
Vertical Mixing ◽  
Energy Spectra ◽  
Small Scale ◽  
Rossby Number ◽  
Vertical Resolution ◽  
Wide Range ◽  
Qualitative Shape ◽  
Vertical Grid

Abstract Many high-resolution atmospheric models can reproduce the qualitative shape of the atmospheric kinetic energy spectrum, which has a power-law slope of −3 at large horizontal scales that shallows to approximately −5/3 in the mesoscale. This paper investigates the possible dependence of model energy spectra on the vertical grid resolution. Idealized simulations forced by relaxation to a baroclinically unstable jet are performed for a wide range of vertical grid spacings Δz. Energy spectra are converged for Δz 200 m but are very sensitive to resolution with 500 m ≤ Δz ≤ 2 km. The nature of this sensitivity depends on the vertical mixing scheme. With no vertical mixing or with weak, stability-dependent mixing, the mesoscale spectra are artificially amplified by low resolution: they are shallower and extend to larger scales than in the converged simulations. By contrast, vertical hyperviscosity with fixed grid-scale damping rate has the opposite effect: underresolved spectra are spuriously steepened. High-resolution spectra are converged except for the stability-dependent mixing case, which are damped by excessive mixing due to enhanced shear over a wide range of horizontal scales. It is shown that converged spectra require resolution of all vertical scales associated with the resolved horizontal structures: these include quasigeostrophic scales for large-scale motions with small Rossby number and the buoyancy scale for small-scale motions at large Rossby number. It is speculated that some model energy spectra may be contaminated by low vertical resolution, and it is recommended that vertical-resolution sensitivity tests always be performed.

scholarly journals Gyrotactic swimmers in turbulence: shape effects and role of the large-scale flow

2018 ◽  
Vol 856 ◽  
Author(s):  
M. Borgnino ◽  
G. Boffetta ◽  
F. De Lillo ◽  
M. Cencini
Keyword(s):  
Large Scale ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Small Scale ◽  
Navier Stokes Equations ◽  
Preferential Sampling ◽  
Wide Range ◽  
Shape Effects ◽  
Dilute Suspensions ◽  
Large Scale Flow

We study the dynamics and the statistics of dilute suspensions of gyrotactic swimmers, a model for many aquatic motile microorganisms. By means of extensive numerical simulations of the Navier–Stokes equations at different Reynolds numbers, we investigate preferential sampling and small-scale clustering as a function of the swimming (stability and speed) and shape parameters, considering in particular the limits of spherical and rod-like particles. While spherical swimmers preferentially sample local downwelling flow, for elongated swimmers we observe a transition from downwelling to upwelling regions at sufficiently high swimming speed. The spatial distribution of both spherical and elongated swimmers is found to be fractal at small scales in a wide range of swimming parameters. The direct comparison between the different shapes shows that spherical swimmers are more clusterized at small stability and speed numbers, while for large values of the parameters elongated cells concentrate more. The relevance of our results for phytoplankton swimming in the ocean is briefly discussed.

scholarly journals Surface toughening – An industrial approach to increase the robustness of pure adhesive joints with film adhesives

2020 ◽  
Vol 234 (13) ◽  
pp. 1980-1987
Author(s):  
MJ Schollerer ◽  
J Kosmann ◽  
D Holzhüter ◽  
C Bello-Larroche ◽  
C Hühne
Keyword(s):  
Large Scale ◽  
Adhesive Bonding ◽  
Bolted Joints ◽  
Small Scale ◽  
Bonded Joints ◽  
Fiber Reinforced ◽  
Load Path ◽  
Stress Concentrations ◽  
Manufacturing Defects ◽  
Wide Range

Bonding is known for its wide range of advantages over bolted joints when joining different materials together. However, the advantages e.g. of homogeneous load distribution can quickly be lost in case of overload. For this reason, the load occurring in the adhesive is reduced by constructive measures far below the yield stress of the adhesive, which leads to a conservative joint design. And to be on the safe side, a few “chicken rivets” are then placed again. This problem is particularly well known in aviation. Highly loaded components are structurally bonded by a combination of rivets and adhesive in order to underline the advantages of structural adhesive bonding with the safety of the well-known bolted joints. Known as fail-safe design, this concept is damage tolerant and more robust against manufacturing defects through a secured double load path.  Especially when joining fiber-reinforced composites, bolts weaken the adherends of the joint and only contribute to load transfer when the brittle adhesive fails. With the help of Surface Toughening, a boltless technique for reducing stress concentrations and arresting cracks in adhesive bonded joints is available. This work describes the industrial application of this technique. Starting with coupon tests and a small scale demonstrator to ensure the compatibility with industrial manufacturing processes, such as infusion and prepreg manufacturing, a large scale demonstrator of a 2 m carbon fiber reinforced plastic (CFRP) - HTP leading edge with hybrid laminar flow control is manufactured by the industrial partner AERnnova. Verifying a simple and cost-effective application of the technology, Surface Toughening enables robust bonded joints with a minimum impact on today's process of adhesive bonding.

Sign in / Sign up

Export Citation Format

Share Document