Effect of Er:YAG Laser Irradiation on Bonding Property of Zirconia Ceramics to Resin Cement

2013 ◽  
Vol 31 (12) ◽  
pp. 619-625 ◽  
Author(s):  
Yihua Lin ◽  
Xiaomeng Song ◽  
Yaming Chen ◽  
Qingping Zhu ◽  
Wei Zhang
Keyword(s):  
Laser Irradiation ◽  
Er:Yag Laser ◽  
Resin Cement ◽  
Zirconia Ceramics ◽  
Bonding Property

scholarly journals Effects of the combination of Er:YAG laser and sandblasting on the shear bond strength between zirconia and resin cement

2019 ◽  
Vol 18 ◽  
pp. e191449
Author(s):  
Urias Silva Vasconcelos ◽  
Thalisson Saymo de Oliveira Silva ◽  
Daylana Pacheco da Silva ◽  
Graciela Maria Oliveira Sipaúba ◽  
Valdimar da Silva Valente ◽  
...  
Keyword(s):  
Shear Strength ◽  
Bond Strength ◽  
Aluminum Oxide ◽  
Surface Treatment ◽  
Laser Irradiation ◽  
Er:Yag Laser ◽  
Resin Cement ◽  
Zirconia Ceramic ◽  
Control Group ◽  
Luting Cement

Aim: This study was conducted to determine the bond strength between zirconia ceramic and resin luting cement according to the type of surface treatment applied. Methods: Sixty zirconia cylinders measuring 4 x 4 mm were manufactured and distributed into five experimental groups and a control group (n = 10): G1 - sandblasting with 110 μm aluminum oxide; G2 - sandblasting with 30 μm Rocatec Soft®; G3 - Er:YAG laser irradiation at 400 mJ; G4 - Er:YAG laser combined with sandblasting with aluminum oxide; G5 - Er:YAG laser combined with sandblasting with Rocatec Soft®; G6 - no treatment (Control). The zirconia cylinders were bonded in the center of composite resin cylinders (6 mm diameter) using RelyX Ultimate® cement. Shear strength was measured after thermocycling (6000 cycles and 5-55° C). Data were analyzed using one-way ANOVA and Tukey's post-hoc with a 5% significance level. Results: Group 4 had a significantly higher shear strength than all the other groups, except Group 1. Group 3 had a significantly lower shear strength compared with Groups 1 and 4. Conclusion: Sandblasting with 110μm aluminum oxide particles after laser irradiation may be an effective zirconia surface treatment. The use of Er: YAG laser alone is not effective at increasing the bond between resin cement and zirconia.

Bonding property of resin cement to composite resin crown

2015 ◽  
Vol 31 ◽  
pp. e21
Author(s):  
O. Aramaki ◽  
R. Takahashi ◽  
T. Wada ◽  
M. Uo ◽  
J. Tagami
Keyword(s):  
Composite Resin ◽  
Resin Cement ◽  
Bonding Property

Effects of the Er:YAG Laser Irradiation on Titanium Implant Materials and Contaminated Implant Abutment Surfaces

2003 ◽  
Vol 21 (1) ◽  
pp. 7-17 ◽  
Author(s):  
Tomoko Matsuyama ◽  
Akira Aoki ◽  
Shigeru Oda ◽  
Takayuki Yoneyama ◽  
Isao Ishikawa
Keyword(s):  
Laser Irradiation ◽  
Er:Yag Laser ◽  
Titanium Implant ◽  
Implant Materials ◽  
Implant Abutment

Surface temperature during cavity preparation on human tooth by Er:YAG laser irradiation

CIRP Annals ◽  
2011 ◽  
Vol 60 (1) ◽  
pp. 555-558 ◽  
Author(s):  
T. Furumoto ◽  
T. Ueda ◽  
A. Kasai ◽  
A. Hosokawa
Keyword(s):  
Surface Temperature ◽  
Laser Irradiation ◽  
Er:Yag Laser ◽  
Human Tooth ◽  
Cavity Preparation

scholarly journals Er:YAG laser-induced damage to a dental composite in simulated clinical scenarios for inadvertent irradiation: an in vitro study

2021 ◽  
Author(s):  
Katharina Kuhn ◽  
Carmen U. Schmid ◽  
Ralph G. Luthardt ◽  
Heike Rudolph ◽  
Rolf Diebolder
Keyword(s):  
Laser Irradiation ◽  
Laser Fluence ◽  
Ablation Threshold ◽  
Er:Yag Laser ◽  
In Vitro Study ◽  
Vitro Study ◽  
Crater Diameter ◽  
Clinical Scenarios ◽  
Laser Induced Damage

AbstractInadvertent Er:YAG laser irradiation occurs in dentistry and may harm restorative materials in teeth. The aim of this in vitro study was to quantify Er:YAG laser-induced damage to a nanohybrid composite in simulated clinical scenarios for inadvertent direct and indirect (reflection) laser irradiation. The simulation was performed by varying the output energy (OE;direct˃indirect) reaching the specimen and the operating distance (OD;direct˂indirect). Composite specimens were irradiated by an Er:YAG laser. The ablation threshold was determined and clinically relevant parameters were applied (n = 6 for each OE/OD combination) for direct (OE: 570 mJ/OD: 10 mm, OE: 190 mJ/OD: 10 mm) and indirect irradiation (OE: 466 mJ/OD: 15 mm, OE: 57 mJ/OD: 15 mm, OE: 155 mJ/OD: 15 mm, OE: 19 mJ/OD: 15 mm). The extent of damage in the form of craters was evaluated using a laser scanning microscope (LSM) and a conventional light microscope (LM). The ablation threshold was determined to be 2.6 J/cm2. The crater diameter showed the highest value (LM: 1075 ± 18 µm/LSM: 1082 ± 17 µm) for indirect irradiation (reflectant:dental mirror) (OE: 466 mJ/OD: 15 mm). The crater depth showed the highest and comparable value for direct (OE: 570 mJ/OD: 10 mm; LSM: 89 ± 2 µm) and indirect irradiation (OE: 466 mJ/OD: 15 mm; LSM: 90 ± 4 µm). For each OD, the crater diameter, depth, and volume increased with higher laser fluence. However, the OD—and thus the laser spot diameter—also had an enlarging effect. Thus, indirect irradiation (reflectant:dental mirror) with only 47% of the laser fluence of direct irradiation led to a larger diameter and a comparable depth. The three-dimensional extent of the crater was large enough to cause roughening, which may lead to plaque accumulation and encourage caries, gingivitis, and periodontitis under clinical conditions. Clinicians should be aware that reflected irradiation can still create such craters.

Bond Strength of Resin Cement and Glass Ionomer to Nd:YAG Laser‐Treated Zirconia Ceramics

2017 ◽  
Vol 28 (4) ◽  
pp. e881-e885 ◽  
Author(s):  
Nafiseh Asadzadeh ◽  
Foojan Ghorbanian ◽  
Farzaneh Ahrary ◽  
Hamidreza Rajati Haghi ◽  
Reza Karamad ◽  
...  
Keyword(s):  
Bond Strength ◽  
Nd:Yag Laser ◽  
Resin Cement ◽  
Glass Ionomer ◽  
Zirconia Ceramics

scholarly journals Human Dental Enamel and Dentin Structural Effects after Er:yag Laser Irradiation

2014 ◽  
Vol 15 (3) ◽  
pp. 283-287 ◽  
Author(s):  
Mateus Rodrigues Tonetto ◽  
Marcelo Ferrarezi de Andrade ◽  
Shelon Cristina Souza Pinto ◽  
Darlon Martins Lima ◽  
José Roberto Cury Saad ◽  
...  
Keyword(s):  
Laser Irradiation ◽  
Soft Tissues ◽  
Er:Yag Laser ◽  
Laser System ◽  
Dental Enamel ◽  
Target Tissue ◽  
Structural Effects ◽  
Ablation Process ◽  
Dental Tissues ◽  
Laser Systems

ABSTRACT Ideally projected to be applied on soft tissues, infrared lasers were improved by restorative dentistry to be used in hard dental tissues cavity preparations — namely enamel and dentin. This paper evidentiates the relevant aspects of infrared Erbium laser's action mechanism and its effects, and characterizes the different effects deriving from the laser's beams emission. The criteria for use and selection of optimal parameters for the correct application of laser systems and influence of supporting factors on the process, such as water amount and its presence in the ablation process, protection exerted by the plasma shielding and structural factors, which are indispensable in dental tissues cavity preparation related to restorative technique, are subordinated to optical modifications caused by the interaction of the energy dissipated by these laser light emission systems in the targeted tissue substrate. Clinical relevance Differences in the action of infrared Erbium laser system in regard to the nature of the ablation process and variations on the morphological aspects observed in the superficial structure of the target tissue irradiated, may be correlated to the structural optical modifications of the substrate produced by an interaction of the energy propagated by laser systems. How to cite this article Lima DM, Tonetto MR, de Mendonça AAM, Elossais AA, Saad JRC, de Andrade MF, Pinto SCS, Bandéca MC. Human Dental Enamel and Dentin Structural Effects after Er:yag Laser Irradiation. J Contemp Dent Pract 2014;15(3):283-287.

Sign in / Sign up

Export Citation Format

Share Document