Probabilistic Approach for Determining the Material Properties of Meniscal Attachments In Vivo Using Magnetic Resonance Imaging and a Finite Element Model

2015 ◽  
Vol 22 (12) ◽  
pp. 1097-1107 ◽  
Author(s):  
Kyoung-Tak Kang ◽  
Sung-Hwan Kim ◽  
Juhyun Son ◽  
Young Han Lee ◽  
Heoung-Jae Chun
Keyword(s):  
Magnetic Resonance Imaging ◽  
Finite Element ◽  
Magnetic Resonance ◽  
Finite Element Model ◽  
Material Properties ◽  
Probabilistic Approach ◽  
Element Model ◽  
Resonance Imaging ◽  
Meniscal Attachments

Finite Element Modeling of Knee Joint Contact Pressures and Comparison to Magnetic Resonance Imaging of the Loaded Knee

2003 ◽  
Author(s):  
Jiang Yao ◽  
Art D. Salo ◽  
Monica Barbu-McInnis ◽  
Amy L. Lerner
Keyword(s):  
Magnetic Resonance Imaging ◽  
Finite Element ◽  
Magnetic Resonance ◽  
Knee Joint ◽  
Material Properties ◽  
Three Dimensional ◽  
Resonance Imaging ◽  
Three Dimensional Model ◽  
Model Predictions

A finite element model of the knee joint could be helpful in providing insight on mechanisms of injury, effects of treatment, and the role of mechanical factors in degenerative conditions. However, preparation of such a model involves many geometric simplifications and input of material properties, some of which are poorly understood. Therefore, a method to compare model predictions to actual behaviors under controlled conditions could provide confidence in the model before exploration of other loading scenarios. Our laboratory has developed a method to apply axial loads to the in vivo human knee during magnetic resonance imaging, resembling weightbearing conditions. Image processing algorithms may then be used to assess the three-dimensional kinematics of the tibia and femur during loading. A three-dimensional model of the tibio-menisco-femoral contact has been generated and the image-based kinematic boundary conditions were applied to investigate the distribution of stresses and strains in the articular cartilage and menisci throughout the loading period. In this study, our goal is to investigate the contact patterns during long term loading of up to twenty minutes in the healthy knee. Specifically, we assess the use of both elastic and poroelastic material properties in the cartilage, and compare model predictions to known loading conditions and images of tissue deformations.

scholarly journals Subject-Specific Finite Element Modeling of the Tibiofemoral Joint Based on CT, Magnetic Resonance Imaging and Dynamic Stereo-Radiography Data in Vivo

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
Robert E. Carey ◽  
Liying Zheng ◽  
Ameet K. Aiyangar ◽  
Christopher D. Harner ◽  
Xudong Zhang
Keyword(s):  
Magnetic Resonance Imaging ◽  
Finite Element ◽  
Magnetic Resonance ◽  
Contact Area ◽  
Resonance Imaging ◽  
Model Predictions ◽  
Subject Specific ◽  
Skeletal Kinematics ◽  
Tibiofemoral Kinematics

In this paper, we present a new methodology for subject-specific finite element modeling of the tibiofemoral joint based on in vivo computed tomography (CT), magnetic resonance imaging (MRI), and dynamic stereo-radiography (DSX) data. We implemented and compared two techniques to incorporate in vivo skeletal kinematics as boundary conditions: one used MRI-measured tibiofemoral kinematics in a nonweight-bearing supine position and allowed five degrees of freedom (excluding flexion-extension) at the joint in response to an axially applied force; the other used DSX-measured tibiofemoral kinematics in a weight-bearing standing position and permitted only axial translation in response to the same force. Verification and comparison of the model predictions employed data from a meniscus transplantation study subject with a meniscectomized and an intact knee. The model-predicted cartilage-cartilage contact areas were examined against “benchmarks” from a novel in situ contact area analysis (ISCAA) in which the intersection volume between nondeformed femoral and tibial cartilage was characterized to determine the contact. The results showed that the DSX-based model predicted contact areas in close alignment with the benchmarks, and outperformed the MRI-based model: the contact centroid predicted by the former was on average 85% closer to the benchmark location. The DSX-based FE model predictions also indicated that the (lateral) meniscectomy increased the contact area in the lateral compartment and increased the maximum contact pressure and maximum compressive stress in both compartments. We discuss the importance of accurate, task-specific skeletal kinematics in subject-specific FE modeling, along with the effects of simplifying assumptions and limitations.

Assessing Patient-Specific Mechanical Properties of Aortic Wall and Peri-Aortic Structures From In Vivo DENSE Magnetic Resonance Imaging Using an Inverse Finite Element Method and Elastic Foundation Boundary Conditions

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Johane H. Bracamonte ◽  
John S. Wilson ◽  
Joao S. Soares
Keyword(s):  
Magnetic Resonance Imaging ◽  
Finite Element Method ◽  
Finite Element ◽  
Magnetic Resonance ◽  
Aortic Wall ◽  
Patient Specific ◽  
Resonance Imaging ◽  
Displacement Fields ◽  
Inverse Finite Element Method

Abstract The establishment of in vivo, noninvasive patient-specific, and regionally resolved techniques to quantify aortic properties is key to improving clinical risk assessment and scientific understanding of vascular growth and remodeling. A promising and novel technique to reach this goal is an inverse finite element method (FEM) approach that utilizes magnetic resonance imaging (MRI)-derived displacement fields from displacement encoding with stimulated echoes (DENSE). Previous studies using DENSE MRI suggested that the infrarenal abdominal aorta (IAA) deforms heterogeneously during the cardiac cycle. We hypothesize that this heterogeneity is driven in healthy aortas by regional adventitial tethering and interaction with perivascular tissues, which can be modeled with elastic foundation boundary conditions (EFBCs) using a collection of radially oriented springs with varying stiffness with circumferential distribution. Nine healthy IAAs were modeled using previously acquired patient-specific imaging and displacement fields from steady-state free procession (SSFP) and DENSE MRI, followed by assessment of aortic wall properties and heterogeneous EFBC parameters using inverse FEM. In contrast to traction-free boundary condition, prescription of EFBC reduced the nodal displacement error by 60% and reproduced the DENSE-derived heterogeneous strain distribution. Estimated aortic wall properties were in reasonable agreement with previously reported experimental biaxial testing data. The distribution of normalized EFBC stiffness was consistent among all patients and spatially correlated to standard peri-aortic anatomical features, suggesting that EFBC could be generalized for human adults with normal anatomy. This approach is computationally inexpensive, making it ideal for clinical research and future incorporation into cardiovascular fluid–structure analyses.

Sign in / Sign up

Export Citation Format

Share Document