scholarly journals Osseointegration of Coarse and Fine Textured Implants Manufactured by Electron Beam Melting and Direct Metal Laser Sintering

2017 ◽  
Vol 4 (2) ◽  
pp. 91-97 ◽  
Author(s):  
David S. Ruppert ◽  
Ola L.A. Harrysson ◽  
Denis J. Marcellin-Little ◽  
Sam Abumoussa ◽  
Laurence E. Dahners ◽  
...  
Keyword(s):  
Electron Beam ◽  
Electron Beam Melting ◽  
Laser Sintering ◽  
Direct Metal Laser Sintering

scholarly journals Effect of Various Peening Methods on the Fatigue Properties of Titanium Alloy Ti6Al4V Manufactured by Direct Metal Laser Sintering and Electron Beam Melting

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2216 ◽  
Author(s):  
Hitoshi Soyama ◽  
Fumio Takeo
Keyword(s):  
Titanium Alloy ◽  
Electron Beam ◽  
Fatigue Strength ◽  
Shot Peening ◽  
Electron Beam Melting ◽  
Surface Hardness ◽  
Laser Sintering ◽  
Laser Peening ◽  
Direct Metal Laser Sintering ◽  
Titanium Alloy Ti6al4v

Titanium alloy Ti6Al4V manufactured by additive manufacturing (AM) is an attractive material, but the fatigue strength of AM Ti6Al4V is remarkably weak. Thus, post-processing is very important. Shot peening can improve the fatigue strength of metallic materials, and novel peening methods, such as cavitation peening and laser peening, have been developed. In the present paper, to demonstrate an improvement of the fatigue strength of AM Ti6Al4V, Ti6Al4V manufactured by direct metal laser sintering (DMLS) and electron beam melting (EBM) was treated by cavitation peening, laser peening, and shot peening, then tested by a plane bending fatigue test. To clarify the mechanism of the improvement of the fatigue strength of AM Ti6Al4V, the surface roughness, residual stress, and surface hardness were measured, and the surfaces with and without peening were also observed using a scanning electron microscope. It was revealed that the fatigue strength at N = 107 of Ti6Al4V manufactured by DMLS was slightly better than that of Ti6Al4V manufactured by EBM, and the fatigue strength of both the DMLS and EBM specimens was improved by about two times through cavitation peening, compared with the as-built ones. An experimental formula to estimate fatigue strength from the mechanical properties of a surface was proposed.

Direct Metal Laser Sintering Strategies for Fabrication of Finer Resolution Cellular Structures

2020 ◽  
Author(s):  
Fatemeh Hejripour ◽  
Muhammad Abdus Salam ◽  
Gary L. Bowlin ◽  
Ebrahim Asadi
Keyword(s):  
Laser Sintering ◽  
Cellular Structures ◽  
Direct Metal Laser Sintering

Assessing Porosity in Selective Electron Beam Melting Manufactured Ti–6Al–4V by Nonlinear Impact Modulation Spectroscopy

2020 ◽  
Vol 39 (4) ◽  
Author(s):  
Jan Kober ◽  
Alexander Kirchner ◽  
Alena Kruisova ◽  
Milan Chlada ◽  
Sigrun Hirsekorn ◽  
...  
Keyword(s):  
Electron Beam ◽  
Electron Beam Melting ◽  
Modulation Spectroscopy ◽  
Selective Electron Beam Melting
Sign in / Sign up

Export Citation Format

Share Document