Accurate Mass Ratio and Heating Effects in the Dual-Line Millisecond Binary Pulsar in NGC 6397

2003 ◽  
Vol 584 (1) ◽  
pp. L13-L16 ◽  
Author(s):  
F. R. Ferraro ◽  
E. Sabbi ◽  
R. Gratton ◽  
A. Possenti ◽  
N. D’Amico ◽  
...  
Keyword(s):  
Accurate Mass ◽  
Mass Ratio ◽  
Binary Pulsar ◽  
Heating Effects

A Quantitative Theory for the Computation of Tire Friction Under Severe Conditions of Sliding

1986 ◽  
Vol 14 (1) ◽  
pp. 44-72 ◽  
Author(s):  
C. M. Mc C. Ettles
Keyword(s):  
Friction Coefficient ◽  
Flash Temperature ◽  
Contact Conditions ◽  
Quantitative Form ◽  
Heating Effects ◽  
Rubber Friction ◽  
Viscoelastic Effects ◽  
Tire Friction ◽  
Pavement Friction ◽  
Metal Polymer

Abstract It is proposed that tire-pavement friction is controlled by thermal rather than by hysteresis and viscoelastic effects. A numerical model of heating effects in sliding is described in which the friction coefficient emerges as a dependent variable. The overall results of the model can be expressed in a closed form using Blok's flash temperature theory. This allows the factors controlling rubber friction to be recognized directly. The model can be applied in quantitative form to metal-polymer-ice contacts. Several examples of correlation are given. The difficulties of characterizing the contact conditions in tire-pavement friction reduce the model to qualitative form. Each of the governing parameters is examined in detail. The attainment of higher friction by small, discrete particles of aluminum filler is discussed.

Analysis of Squalene and Its Transformation By-Products in Latent Fingermarks by Ultrahigh-Pressure Liquid Chromatography-High Resolution Accurate Mass Orbitrap™ Mass Spectrometry

2019 ◽  
Author(s):  
Buddhika Dorakumbura ◽  
Francesco Busetti ◽  
Simon Lewis
Keyword(s):  
Mass Spectrometry ◽  
Liquid Chromatography ◽  
High Resolution ◽  
Storage Conditions ◽  
Ultrahigh Pressure ◽  
Accurate Mass ◽  
Rational Approach ◽  
By Products ◽  
Over Time ◽  
High Resolution Accurate Mass

<p>Transformation of squalene and its by-products in fingermarks over time under different storage conditions (light, dark and underwater) was examined through ultrahigh-pressure liquid chromatography high resolution accurate mass Orbitrap™ mass spectrometry. Complications of assessing fingermark compositional variation over time using multiple samples with varying initial compositions were elucidated and a more rational approach was successfully demonstrated. Squalene was detected in all fresh natural fingermarks and the amount ranged between 0.20 to 11.32 μg/5 fingertips. A notable difference in the transformation of squalene was observed with different storage conditions, where a dark aquatic environment accelerated degradation of squalene compared to dark but dry conditions. Squalene monohydroperoxide was extremely short-lived in natural deposits while the amount of squalene epoxide was still increasing relative to the initial amount, after ageing under dark and aquatic conditions for up to 7 days. Some oxidation by-products of cholesterol were also tentatively identified, which exhibited a growth over time against their initial concentration under any of the storage condition tested. These by-products, therefore, show potential as biomarkers for targeted visualisation of aged deposits.</p>

Laser Failure Isolation Techniques Demonstrated On Test Structures

2008 ◽  
Author(s):  
Frank S. Arnold
Keyword(s):  
Integrated Circuits ◽  
Laser Beam ◽  
Case Studies ◽  
Induced Resistance ◽  
Simple Test ◽  
Resistance Change ◽  
Cross Sectional ◽  
Beam Focusing ◽  
Isolation Techniques ◽  
Heating Effects

Abstract To be better prepared to use laser based failure isolation techniques on field failures of complex integrated circuits, simple test structures without any failures can be used to study Optical Beam Induced Resistance Change (OBIRCH) results. In this article, four case studies are presented on the following test structures: metal strap, contact string, VIA string, and comb test structure. Several experiments were done to investigate why an OBIRCH image was seen in certain areas of a VIA string and not in others. One experiment showed the OBRICH variation was not related to the cooling and heating effects of the topology, or laser beam focusing. A 4 point probe resistance measurement and cross-sectional views correlated with the OBIRCH results and proved OBIRCH was able to detect a variation in VIA fabrication.

Sign in / Sign up

Export Citation Format

Share Document