A Study of Partial Extinction and Reignition Effects in Turbulent Non-Premixed Jet Flames of CH4and CO/H2/N2with a Two-Scalar Reactedness-Mixture Fraction Presumed PDF Model

2000 ◽  
Vol 154 (1) ◽  
pp. 31-55 ◽  
Author(s):  
P. KOUTMOS ◽  
C. MAVRIDIS
Keyword(s):  
Mixture Fraction ◽  
Jet Flames ◽  
Partial Extinction ◽  
Presumed Pdf ◽  
Pdf Model

Prediction of Soot Formation Trends in Turbulent Kerosene-Air Diffusion Jet Flames With Elevated Operating Pressure

2017 ◽  
Author(s):  
Pravin Nakod ◽  
Saurabh Patwardhan ◽  
Ishan Verma ◽  
Stefano Orsino
Keyword(s):  
Environmental Protection Agency ◽  
Volume Fraction ◽  
Soot Formation ◽  
Mixture Fraction ◽  
Soot Volume Fraction ◽  
Operating Pressure ◽  
Jet Flames ◽  
Emission Standard ◽  
Radial Profiles ◽  
Air Diffusion

Emission standard agencies are coming up with more stringent regulations on soot, given its adverse effect on human health. It is expected that Environmental Protection Agency (EPA) will soon place stricter regulations on allowed levels of the size of soot particles from aircraft jet engines. Since, aircraft engines operate at varying operating pressure, temperature and air-fuel ratios, soot fraction changes from condition to condition. Computation Fluid Dynamics (CFD) simulations are playing a key role in understanding the complex mechanism of soot formation and the factors affecting it. In the present work, soot formation prediction from numerical analyses for turbulent kerosene-air diffusion jet flames at five different operating pressures in the range of 1 atm. to 7 atm. is presented. The geometrical and test conditions are obtained from Young’s thesis [1]. Coupled combustion-soot simulations are performed for all the flames using steady diffusion flamelet model for combustion and Mass-Brookes-Hall 2-equation model for soot with a 2D axisymmetric mesh. Combustion-Soot coupling is required to consider the effect of soot-radiation interaction. Simulation results in the form of axial and radial profiles of temperature, mixture fraction and soot volume fraction are compared with the corresponding experimental measured profiles. The results for temperature and mixture fraction compare well with the experimental profiles. Predicted order of magnitude and the profiles of the soot volume fraction also compare well with the experimental results. The correct trend of increasing the peak soot volume fraction with increasing the operating pressure is also captured.

Comparison of Numerical and Experimental Results of a Premixed DLE Gas Turbine Combustor

2001 ◽  
Author(s):  
Ruud L. G. M. Eggels ◽  
Christopher T. Brown
Keyword(s):  
Reaction Mechanism ◽  
Gas Turbine ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Gas Turbine Combustor ◽  
Cfd Modelling ◽  
Recirculation Length ◽  
Global Reaction ◽  
Presumed Pdf ◽  
Pdf Model

A numerical and experimental study on a premixed DLE gas turbine combustor has been performed. Experiments and CFD modelling have been carried out at isothermal and combusting conditions. The measurements were obtained at ERC using two component Laser Doppler Velocimetry. To be able to access the inner part of the combustor, the liners of the combustion chamber were outfitted with quartz windows. Temperature measurements were obtained at a few planes using a thermocouple. Modelling of the combustor has been performed using an in-house CFD code. The combustion process has been modelled using a global reaction mechanism and a Flame Generated Manifold reaction mechanism in combination with a presumed PDF model to incorporate the effect of turbulent fluctuations. The Flame Generated Manifold method uses a flame library, which has been generated by performing a number of laminar one-dimensional flame calculations at representative conditions. Comparing the numerical and experimental quite some differences are observed. The CFD model is able to predict the main features of the flow and combustion process, but does not predict the recirculation length accurately. Both combustion models, however, are able to predict the low combustion efficiency measured at the 1atm test condition.

Large Eddy Simulation of a Lean Gas Turbine Model Combustor

2009 ◽  
Author(s):  
M. Staufer ◽  
J. Janicka
Keyword(s):  
Experimental Data ◽  
Large Eddy Simulation ◽  
Flame Surface ◽  
Eddy Simulation ◽  
Partially Premixed Combustion ◽  
Large Eddy ◽  
Partially Premixed ◽  
Partially Premixed Flame ◽  
Presumed Pdf ◽  
Pdf Model

Partially premixed flames although common on many technical devices are difficult to model in numerical simulations. In this paper a Large Eddy Simulation of a lean combustor is presented. To account for mixing effects in case of partially premixed combustion, a suitable extension to the well known coherent flame model (CFM) is applied. The turbulent reaction rate of the partially premixed flame is approximated by solving an additional transport equation for the flame surface density which accounts for flame wrinkling effects as well as for the creation and destruction of flame surface due to stretch and strain effects. The variation of stoichiometry in the flame is accounted for by using a suitable presumed PDF methodology. The pdf-model represents finite rate, as well as non-equilibrium chemistry effects in the flame. The model has been validated against experimental data. The results show an overall reasonable agreement with experimental data, both in profile shapes as well as peak values.

A MULTI-DIRAC PRESUMED PDF MODEL FOR TURBULENT REACTIVE FLOWS WITH VARIABLE EQUIVALENCE RATIO

2006 ◽  
Vol 178 (10-11) ◽  
pp. 1843-1870 ◽  
Author(s):  
VINCENT ROBIN ◽  
ARNAUD MURA ◽  
MICHEL CHAMPION ◽  
PIERRE PLION
Keyword(s):  
Equivalence Ratio ◽  
Reactive Flows ◽  
Turbulent Reactive Flows ◽  
Presumed Pdf ◽  
Pdf Model

scholarly journals High-Momentum Jet Flames at Elevated Pressure, C: Statistical Distribution of Thermochemical States Obtained From Laser-Raman Measurements

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Holger Ax ◽  
Oliver Lammel ◽  
Rainer Lückerath ◽  
Michael Severin
Keyword(s):  
Gas Turbine ◽  
Mixture Fraction ◽  
Turbulent Flame ◽  
Elevated Pressure ◽  
Flame Stabilization ◽  
Strong Mixing ◽  
Single Shot ◽  
High Momentum ◽  
Jet Flames ◽  
Laser Raman

Abstract A detailed investigation on flame structures and stabilization mechanisms of confined high momentum jet flames by one-dimensional (1D)-laser Raman measurements is presented. The flames were operated with natural gas (NG) at gas turbine relevant conditions in an optically accessible high-pressure test rig. The generic burner represents a full scale single nozzle of a high temperature FLOX® gas turbine combustor including a pilot stage. 1D-laser Raman measurements were performed on both an unpiloted and a piloted flame and evaluated on a single shot basis revealing the thermochemical states from unburned inflow conditions to burned hot gas in terms of average and statistical values of the major species concentrations, the mixture fraction and the temperature. The results show a distinct difference in the flame stabilization mechanism between the unpiloted and the piloted case. The former is apparently driven by strong mixing of fresh unburned gas and recirculated hot burned gas that eventually causes autoignition. The piloted flame is stabilized by the pilot stage followed by turbulent flame propagation. The findings help to understand the underlying combustion mechanisms and to further develop gas turbine burners following the FLOX concept.

scholarly journals Reaction-rate, mixture-fraction, and temperature imaging in turbulent methane/air jet flames

2002 ◽  
Vol 29 (2) ◽  
pp. 2687-2694 ◽  
Author(s):  
Jonathan H. Frank ◽  
Sebastian A. Kaiser ◽  
Marshall B. Long
Keyword(s):  
Reaction Rate ◽  
Mixture Fraction ◽  
Jet Flames ◽  
Temperature Imaging ◽  
Air Jet
Sign in / Sign up

Export Citation Format

Share Document