scholarly journals A comparison of charcoal reflectance between crown and surface fire contexts in dry south-west USA forests

2018 ◽  
Vol 27 (6) ◽  
pp. 396 ◽  
Author(s):  
Christopher I. Roos ◽  
Andrew C. Scott
Keyword(s):  
Ponderosa Pine ◽  
Fire Severity ◽  
Prescribed Fires ◽  
Crown Fire ◽  
Fire Behaviour ◽  
Surface Fire ◽  
Surface Fires ◽  
South West ◽  
Crown Fires ◽  
Mixed Conifer Forests

The historical and modern importance of crown fires in ponderosa pine and dry mixed-conifer forests of the south-west USA has been much debated. The microscopic reflectance of charcoal in polished blocks under oil shows promise as a semiquantitative proxy for fire severity using charcoal from post-fire landscapes. We measured the reflectance of 33 modern charcoal samples to evaluate (1) whether charcoal reflectance can distinguish between crown fires and surface fires in these forests; and (2) whether surface fires with masticated fuels burn with severities similar to surface fires in grass, litter and duff fuels. The charcoal analysed was primarily collected after wildland fires under two different conditions: (l) wildfires with moderate to high severity and crown fire behaviour (n = 17), and (2) prescribed fires with low to moderate severity but no crown fire behaviour (n = 16). Statistical analysis indicates that charcoal reflectance produced in crown fires significantly differs from surface fire charcoal, particularly surface fire charcoal formed in grass, duff and litter fuels. However, charcoal produced from surface fires in masticated fuels is indistinguishable from crown fire charcoal, suggesting that fires in areas that have experienced in situ mastication may have soil impacts similar to crown fires.

Modelling the rate of fire spread and uncertainty associated with the onset and propagation of crown fires in conifer forest stands

2017 ◽  
Vol 26 (5) ◽  
pp. 413 ◽  
Author(s):  
Miguel G. Cruz ◽  
Martin E. Alexander
Keyword(s):  
Monte Carlo ◽  
Average Rate ◽  
Fire Spread ◽  
Prediction Errors ◽  
Crown Fire ◽  
Conifer Forest ◽  
Fire Behaviour ◽  
Crown Fires ◽  
Deterministic Modelling ◽  
Eastern Australia

Crown fires are complex, unstable phenomena dependent on feedback mechanisms between the combustion products of distinct fuel layers. We describe non-linear fire behaviour associated with crowning and the uncertainty they cause in fire behaviour predictions by running a semiphysical modelling system within a simple Monte Carlo simulation framework. The method was able to capture the dynamics of passive and active crown fire spread regimes, providing estimates of average rate of spread and the extent of crown fire activity. System outputs were evaluated against data collected from a wildfire that occurred in a radiata pine plantation in south-eastern Australia. The Monte Carlo method reduced prediction errors relative to the more commonly used deterministic modelling approach, and allowed a more complete description of the level of crown fire behaviour to expect. The method also provides uncertainty measures and probabilistic outputs, extending the range of questions that can be answered by fire behaviour models.

Effect of thinning and prescribed burning on crown fire severity in ponderosa pine forests

2002 ◽  
Vol 11 (1) ◽  
pp. 1 ◽  
Author(s):  
Jolie Pollet ◽  
Philip N. Omi
Keyword(s):  
Prescribed Fire ◽  
Ponderosa Pine ◽  
Stand Structure ◽  
Fire Severity ◽  
Fire Effects ◽  
Pine Forests ◽  
Crown Fire ◽  
Fuel Treatments ◽  
Ponderosa Pine Forests ◽  
Wildfire Hazard

Fire exclusion policies have affected stand structure and wildfire hazard in north American ponderosa pine forests. Wildfires are becoming more severe in stands where trees are densely stocked with shade-tolerant understory trees. Although forest managers have been employing fuel treatment techniques to reduce wildfire hazard for decades, little scientific evidence documents the success of treatments in reducing fire severity. Our research quantitatively examined fire effects in treated and untreated stands in western United States national forests. Four ponderosa pine sites in Montana, Washington, California and Arizona were selected for study. Fuel treatments studied include: prescribed fire only, whole-tree thinning, and thinning followed by prescribed fire. On-the-ground fire effects were measured in adjacent treated and untreated forests. We developed post facto fire severity and stand structure measurement techniques to complete field data collection. We found that crown fire severity was mitigated in stands that had some type of fuel treatment compared to stands without any treatment. At all four of the sites, the fire severity and crown scorch were significantly lower at the treated sites. Results from this research indicate that fuel treatments, which remove small diameter trees, may be beneficial for reducing crown fire hazard in ponderosa pine sites.

Interdependencies between flame length and fireline intensity in predicting crown fire initiation and crown scorch height

2012 ◽  
Vol 21 (2) ◽  
pp. 95 ◽  
Author(s):  
Martin E. Alexander ◽  
Miguel G. Cruz
Keyword(s):  
Wildland Fire ◽  
Stem Bark ◽  
Flame Length ◽  
Flame Height ◽  
Crown Fire ◽  
Fire Behaviour ◽  
Surface Fire ◽  
Crown Scorch ◽  
Fire Initiation ◽  
Bark Char

This state-of-knowledge review examines some of the underlying assumptions and limitations associated with the inter-relationships among four widely used descriptors of surface fire behaviour and post-fire impacts in wildland fire science and management, namely Byram’s fireline intensity, flame length, stem-bark char height and crown scorch height. More specifically, the following topical areas are critically examined based on a comprehensive review of the pertinent literature: (i) estimating fireline intensity from flame length; (ii) substituting flame length for fireline intensity in Van Wagner’s crown fire initiation model; (iii) the validity of linkages between the Rothermel surface fire behaviour and Van Wagner’s crown scorch height models; (iv) estimating flame height from post-fire observations of stem-bark char height; and (v) estimating fireline intensity from post-fire observations of crown scorch height. There has been an overwhelming tendency within the wildland fire community to regard Byram’s flame length–fireline intensity and Van Wagner’s crown scorch height–fireline intensity models as universal in nature. However, research has subsequently shown that such linkages among fire behaviour and post-fire impact characteristics are in fact strongly influenced by fuelbed structure, thereby necessitating consideration of fuel complex specific-type models of such relationships.

Corrigendum to: Interdependencies between flame length and fireline intensity in predicting crown fire initiation and crown scorch height

2017 ◽  
Vol 26 (4) ◽  
pp. 345 ◽  
Author(s):  
Martin E. Alexander ◽  
Miguel G. Cruz
Keyword(s):  
Wildland Fire ◽  
Stem Bark ◽  
Flame Length ◽  
Flame Height ◽  
Crown Fire ◽  
Fire Behaviour ◽  
Surface Fire ◽  
Crown Scorch ◽  
Fire Initiation ◽  
Bark Char

This state-of-knowledge review examines some of the underlying assumptions and limitations associated with the inter-relationships among four widely used descriptors of surface fire behaviour and post-fire impacts in wildland fire science and management, namely Byram's fireline intensity, flame length, stem-bark char height and crown scorch height. More specifically, the following topical areas are critically examined based on a comprehensive review of the pertinent literature: (i) estimating fireline intensity from flame length; (ii) substituting flame length for fireline intensity in Van Wagner's crown fire initiation model; (iii) the validity of linkages between the Rothermel surface fire behaviour and Van Wagner's crown scorch height models; (iv) estimating flame height from post-fire observations of stem-bark char height; and (v) estimating fireline intensity from post-fire observations of crown scorch height. There has been an overwhelming tendency within the wildland fire community to regard Byram's flame length–fireline intensity and Van Wagner's crown scorch height–fireline intensity models as universal in nature. However, research has subsequently shown that such linkages among fire behaviour and post-fire impact characteristics are in fact strongly influenced by fuelbed structure, thereby necessitating consideration of fuel complex specific-type models of such relationships.

The effect of fire front width on surface fire behaviour

1999 ◽  
Vol 9 (4) ◽  
pp. 247 ◽  
Author(s):  
B.M. Wotton ◽  
R.S. McAlpine ◽  
M.W. Hobbs
Keyword(s):  
Forest Litter ◽  
Fire Spread ◽  
Fire Behaviour ◽  
Pine Plantation ◽  
Spread Rate ◽  
Surface Fire ◽  
Flame Radiation ◽  
Surface Fires ◽  
Front Width ◽  
Fire Front

To determine the effect of fire front width on surface fire spread rates, a series of simultaneously ignited experimental fires was carried out in a pine plantation. Fires were ignited in plots with widths ranging from 0.5 m to 10 m and were burned in low wind conditions. Flame lengths were small in all fires, ranging from 20 cm to 60 cm. Since pre-heating of the forest litter from flame radiation is assumed to be an important mechanism in the spread of low intensity, low wind surface fires, it then follows that the width of a flaming front should effect on the heating of the fuel to ignition temperatures. Total flame radiation was also measured at a point 50 cm ahead of the advancing flame front for a number of the fires. Experimental results indicate that a flame radiation measured ahead of the fire stays fairly constant once the flame width is between 2 and 5 m. Theoretical flame radiation calculations confirm this trend. Rates of spread between the 5 and 10 metre width fires also appear to be similar; this indicates that, for the type of fires studied, once flame width is greater than about 2 m, radiation from any extra width of fire front has little effect on spread rate.

Crown fire behaviour in a northern jack pine – black spruce forest

2004 ◽  
Vol 34 (8) ◽  
pp. 1548-1560 ◽  
Author(s):  
B J Stocks ◽  
M E Alexander ◽  
B M Wotton ◽  
C N Stefner ◽  
M D Flannigan ◽  
...  
Keyword(s):  
Black Spruce ◽  
Significant Proportion ◽  
Weather Conditions ◽  
Crown Fire ◽  
Fire Behaviour ◽  
Fire Modelling ◽  
Crown Fires ◽  
Floor Layer ◽  
Prediction Systems ◽  
High Degree

This paper reports on the behaviour of 10 experimental crown fires conducted between 1997 and 2000 during the International Crown Fire Modelling Experiment (ICFME) in Canada's Northwest Territories. The primary goal of ICFME was a replicated series of high-intensity crown fires designed to validate and improve existing theoretical and empirical models of crown fire behaviour. Fire behaviour characteristics were typical for fully developed boreal forest crown fires, with fires advancing at 15–70 m/min, consuming significant quantities of fuel (2.8–5.5 kg/m2) and releasing vast amounts of thermal heat energy. The resulting flame fronts commonly extended 25–40 m above the ground with head fire intensities up to 90 000 kW/m. Depth of burn ranged from 1.4–3.6 cm, representing a 25%–65% reduction in the thickness of the forest floor layer. Most of the smaller diameter (<3.0 cm) woody surface fuels were consumed, along with a significant proportion of the larger downed woody material. A high degree of fuel consumption occurred in the understory and overstory canopy with very little material less than 1.0 cm in diameter remaining. The documentation of fire behaviour, fire danger, and fire weather conditions carried out during ICFME permitted the evaluation of several empirically based North American fire behaviour prediction systems and models.

Variation in wind and crown fire behaviour in a northern jack pine – black spruce forest

2004 ◽  
Vol 34 (8) ◽  
pp. 1561-1576 ◽  
Author(s):  
S W Taylor ◽  
B M Wotton ◽  
M E Alexander ◽  
G N Dalrymple
Keyword(s):  
Black Spruce ◽  
Flame Temperature ◽  
Fire Spread ◽  
Crown Fire ◽  
Fire Behaviour ◽  
Canopy Layer ◽  
Crown Fires ◽  
Video Observations ◽  
Before And After ◽  
Fire Front

Fire spread and flame temperature were examined in a series of nine experimental crown fires conducted in the Northwest Territories, Canada. Average rates of spread were 17.8–66.8 m·min–1 (0.3–1.1 m·s–1) over burning periods from about 1.5–10 min across 75 m × 75 m to 150 m × 150 m plots. Detailed maps of fire front progression revealed areas with higher rates of spread in the order of tens of metres in horizontal dimension and tens of seconds in duration in several of the fires, which is consistent with the influence of coherent wind gusts. Comparison of open and in-stand wind speed before and after burning suggests that defoliation in the canopy layer during burning would result in the flaming zone having greater exposure to the ambient wind. Estimates of flame front residence from video observations at the surface averaged 34 s; estimates from temperature measurements decreased significantly with height from 74 s at the surface to 31 s below the canopy.

Fuel treatments alter the effects of wildfire in a mixed-evergreen forest, Oregon, USA

2005 ◽  
Vol 35 (12) ◽  
pp. 2981-2995 ◽  
Author(s):  
Crystal L Raymond ◽  
David L Peterson
Keyword(s):  
Tree Mortality ◽  
Fire Regime ◽  
Fire Severity ◽  
Fire Behavior ◽  
Evergreen Forest ◽  
Fire Intensity ◽  
Crown Fire ◽  
Fuel Loading ◽  
Fuel Treatments ◽  
Surface Fire

We had the rare opportunity to quantify the relationship between fuels and fire severity using prefire surface and canopy fuel data and fire severity data after a wildfire. The study area is a mixed-evergreen forest of southwestern Oregon with a mixed-severity fire regime. Modeled fire behavior showed that thinning reduced canopy fuels, thereby decreasing the potential for crown fire spread. The potential for crown fire initiation remained fairly constant despite reductions in ladder fuels, because thinning increased surface fuels, which contributed to greater surface fire intensity. Thinning followed by underburning reduced canopy, ladder, and surface fuels, thereby decreasing surface fire intensity and crown fire potential. However, crown fire is not a prerequisite for high fire severity; damage to and mortality of overstory trees in the wildfire were extensive despite the absence of crown fire. Mortality was most severe in thinned treatments (80%–100%), moderate in untreated stands (53%–54%), and least severe in the thinned and underburned treatment (5%). Thinned treatments had higher fine-fuel loading and more extensive crown scorch, suggesting that greater consumption of fine fuels contributed to higher tree mortality. Fuel treatments intended to minimize tree mortality will be most effective if both ladder and surface fuels are treated.

Late Holocene geomorphic record of fire in ponderosa pine and mixed-conifer forests, Kendrick Mountain, northern Arizona, USA

2011 ◽  
Vol 20 (1) ◽  
pp. 125 ◽  
Author(s):  
Sara E. Jenkins ◽  
Carolyn Hull Sieg ◽  
Diana E. Anderson ◽  
Darrell S. Kaufman ◽  
Philip A. Pearthree
Keyword(s):  
Debris Flow ◽  
Ponderosa Pine ◽  
Debris Flows ◽  
Late Holocene ◽  
Conifer Forests ◽  
Fire Behaviour ◽  
Mixed Conifer ◽  
Northern Arizona ◽  
Mixed Conifer Forests ◽  
Steep Slopes

Long-term fire history reconstructions enhance our understanding of fire behaviour and associated geomorphic hazards in forested ecosystems. We used 14C ages on charcoal from fire-induced debris-flow deposits to date prehistoric fires on Kendrick Mountain, northern Arizona, USA. Fire-related debris-flow sedimentation dominates Holocene fan deposition in the study area. Radiocarbon ages indicate that stand-replacing fire has been an important phenomenon in late Holocene ponderosa pine (Pinus ponderosa) and ponderosa pine–mixed conifer forests on steep slopes. Fires have occurred on centennial scales during this period, although temporal hiatuses between recorded fires vary widely and appear to have decreased during the past 2000 years. Steep slopes and complex terrain may be responsible for localised crown fire behaviour through preheating by vertical fuel arrangement and accumulation of excessive fuels. Holocene wildfire-induced debris flow events occurred without a clear relationship to regional climatic shifts (decadal to millennial), suggesting that interannual moisture variability may determine fire year. Fire-debris flow sequences are recorded when (1) sufficient time has passed (centuries) to accumulate fuels; and (2) stored sediment is available to support debris flows. The frequency of reconstructed debris flows should be considered a minimum for severe events in the study area, as fuel production may outpace sediment storage.

scholarly journals Modelling initial mortality of Abies religiosa in a crown fire in Mexico

2016 ◽  
Vol 25 (1) ◽  
pp. 047
Author(s):  
Salomé Temiño-Villota ◽  
Dante A. Rodríguez-Trejo ◽  
Domingo M. Molina Terrén ◽  
Kevin Ryan
Keyword(s):  
Fire Severity ◽  
Negative Relationship ◽  
Crown Fire ◽  
Southern Mexico ◽  
Crown Length ◽  
Crown Fires ◽  
Morphological Variables ◽  
Crown Base Height ◽  
Abies Religiosa ◽  
The Impact

Aim of study: The objectives of this work were to determine which morphological and fire severity variables may help explain the mortality of adult Abies religiosa (Kunth) Schltdl. & Cham., to model the probability of this species after being affected by crown fire, and to obtain more elements to classify the sacred fir in terms of fire resistance. This type of studies are relevant to estimate the impact of crown fires on the climax forests that forms this species.Area of study: The burned forest was located in the southern Mexico City, borough.Material and methods: Morphological variables and fire severity indicators were collected for 335 Abies religiosa trees burned by a mixed severity fire. Logistic regression was used to analyze data and develop models that best explained tree mortality.Main results: Survival was 26.9%. The models for height (p≤0.0001), diameter at breast height (p=0.0082), crown length (p≤0.0001) and crown base height (p≤0.0001) were significant, with a negative relationship between each one of these variables and probability of mortality. The significant severity variables were lethal scorch height (p≤0.0001) and crown kill (p≤ 0.0001), which have a direct relationship with probability of mortality.Highlights: This species is moderately fire-resistant. Crown kill ≥ 70% markedly increases mortality. Silvicultural activities such as pruning, thinning and fuel management can reduce the risk of crown fires.

Sign in / Sign up

Export Citation Format

Share Document