scholarly journals Slowing of Sound Waves in Powdered Media

1989 ◽  
Vol 42 (6) ◽  
pp. 627 ◽  
Author(s):  
JM Brettell
Keyword(s):  
Wave Propagation ◽  
Sound Velocity ◽  
Ultrasonic Wave ◽  
Coupled Oscillators ◽  
Bulk Material ◽  
Sound Waves ◽  
Ultrasonic Wave Propagation ◽  
Fine Grain ◽  
Linear Chains

The velocities of longitudinal sound waves in powdered media are considerably less than the corresponding value in bulk material. To understand this further, an examination has been made of how the sound velocity varies with pressure for the particular case of ultrasonic wave propagation in fine-grain sand. An analysis of the data has been made by treating the particles as linear chains of coupled oscillators.

Simulation study of axial ultrasonic wave propagation in heterogeneous bovine cortical bone

2016 ◽  
Vol 140 (5) ◽  
pp. 3710-3717 ◽  
Author(s):  
Toshiho Hata ◽  
Yoshiki Nagatani ◽  
Koki Takano ◽  
Mami Matsukawa
Keyword(s):  
Wave Propagation ◽  
Cortical Bone ◽  
Ultrasonic Wave ◽  
Simulation Study ◽  
Ultrasonic Wave Propagation

scholarly journals High Frequency Ultrasonic Wave Propagation in  Anisotropic Materials

2021 ◽  
Author(s):  
◽  
Andrew Paul Dawson
Keyword(s):  
Wave Propagation ◽  
Ultrasonic Wave ◽  
High Frequency ◽  
Guided Wave ◽  
Ultrasonic Waves ◽  
Tissue Characterisation ◽  
Ultrasonic Wave Propagation ◽  
Matching Layer ◽  
Fibrous Tissues ◽  
Wave Modes

<p>The influence of highly regular, anisotropic, microstructured materials on high frequency ultrasonic wave propagation was investigated in this work. Microstructure, often only treated as a source of scattering, significantly influences high frequency ultrasonic waves, resulting in unexpected guided wave modes. Tissues, such as skin or muscle, are treated as homogeneous by current medical ultrasound systems, but actually consist of highly anisotropic micron-sized fibres. As these systems increase towards 100 MHz, these fibres will significantly influence propagating waves leading to guided wave modes. The effect of these modes on image quality must be considered. However, before studies can be undertaken on fibrous tissues, wave propagation in more ideal structures must be first understood. After the construction of a suitable high frequency ultrasound experimental system, finite element modelling and experimental characterisation of high frequency (20-200 MHz) ultrasonic waves in ideal, collinear, nanostructured alumina was carried out. These results revealed interesting waveguiding phenomena, and also identified the potential and significant advantages of using a microstructured material as an alternative acoustic matching layer in ultrasonic transducer design. Tailorable acoustic impedances were achieved from 4-17 MRayl, covering the impedance range of 7-12 MRayl most commonly required by transducer matching layers. Attenuation coefficients as low as 3.5 dBmm-1 were measured at 100 MHz, which is excellent when compared with 500 dBmm-1 that was measured for a state of the art loaded epoxy matching layer at the same frequency. Reception of ultrasound without the restriction of critical angles was also achieved, and no dispersion was observed in these structures (unlike current matching layers) until at least 200 MHz. In addition, to make a significant step forward towards high frequency tissue characterisation, novel microstructured poly(vinyl alcohol) tissue-mimicking phantoms were also developed. These phantoms possessed acoustic and microstructural properties representative of fibrous tissues, much more realistic than currently used homogeneous phantoms. The attenuation coefficient measured along the direction of PVA alignment in an example phantom was 8 dBmm-1 at 30 MHz, in excellent agreement with healthy human myocardium. This method will allow the fabrication of more realistic and repeatable phantoms for future high frequency tissue characterisation studies.</p>

Sign in / Sign up

Export Citation Format

Share Document