Air temperature prediction model to control solar energy heating in a germination greenhouse at night

1998 ◽  
Vol 38 (4) ◽  
pp. 409 ◽  
Author(s):  
Ibrahim E. A. Elbatawi
Keyword(s):  
Solar System ◽  
Solar Energy ◽  
Air Temperature ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Weather Forecast ◽  
Hot Water ◽  
Outdoor Air ◽  
Maximum Temperatures ◽  
Air Temperature Prediction

Summary. The outdoor air temperature is not constant especially in spring in Okayama city. The average night temperature ranges from –2 to 20°C which is too low for the germination of most seeds. A good knowledge of the future outdoor air temperature is necessary to decide if greenhouse heating is needed for the next day. Using measured temperatures from the preceding days and considering the minimum and maximum temperatures given by the weather forecast, it was possible to accurately compute the temperature for the next day. Pumpkin, eggplant and tomato seeds were used in this study. A solar system was used to heat the air inside a greenhouse at night using an air–water–air heat exchanger and make a comparison with an unheated greenhouse. The performance of the solar collector and methods of heat exchange were tested. It was shown that the solar energy collected was sufficient for warming a nursery greenhouse overnight. The system operated with a hot water flow rate of 0.647 L/min and an air flow rate of 9.21 m3/min and could maintain the greenhouse temperature between 16 and 20°C. The quantity of heat collected and delivered by the solar system from incident solar radiation was about 50% in a day. Heating the air inside the greenhouse at night produced 100% germination for all seedlings. In comparison, in the unheated greenhouse the germination ratio was 100, 93 and 27% for pumpkin, eggplant and tomato respectively. The germination ratio outside the greenhouses was 100% for pumpkin, 67% for eggplant and zero for tomato.

A Method for Calculating the Unsaturated Humid Air Flow Section Length in the Mechanical Draft Cooling Tower Sprinkler Channel

Vestnik MEI ◽  
2021 ◽  
pp. 37-43
Author(s):  
Vasiliy Ya. Gubarev ◽  
◽  
Aleksey G. Arzamastsev ◽  
Aleksey I. Sharapov ◽  
Yuliya O. Moreva ◽  
...  
Keyword(s):  
Mass Transfer ◽  
Air Temperature ◽  
Flow Rate ◽  
Cooling Tower ◽  
Initial Conditions ◽  
Air Flow ◽  
Water Flow Rate ◽  
Flow Section ◽  
Transfer Coefficients ◽  
Humid Air

In the channels of mechanical-draft cooling tower sprinklers, a saturated air flow section may appear under certain initial conditions, the mass transfer intensity in which is limited by the steam content in the saturated air. For correctly calculating the heat and mass transfer processes in the cooling tower channel, it is necessary to have a method for determining the unsaturated air flow section length. Publications devoted to studying water cooling processes in the channels of mechanical-draft cooling tower sprinklers do not contain an assessment of the unsaturated air flow section length. A method for determining the unsaturated humid air flow section length in the mechanical-draft cooling tower sprinkler channels is proposed, which is based on the well-known criterion equations for calculating the heat transfer and mass transfer coefficients. The effect the initial air parameters have on the unsaturated air section length is studied, and graphic dependences of the unsaturated air section length are drawn up for each of the analyzed parameters. It is shown that the unsaturated humid air flow section length increases with increasing the initial air temperature. It is also found that the unsaturated air flow section length decreases with a growth in the relative air humidity. An increase in the air flow rate with a constant water flow rate leads to an increase in the unsaturated air flow section length. For the considered sprinkler channel, the saturated air region exists at an air temperature of 15°C and below, and for air temperatures above 25°C there is no saturated air flow section. It is shown that the conclusions drawn about the effect the initial air parameters have on the relative change in the unsaturated air flow section length are valid for channels of various shapes and geometric sizes. The proposed methodology and the results obtained can be used in designing mechanical-draft cooling towers and estimating their efficiency.

scholarly journals Mapping Relevant Parameters for Efficient Operation of Low-Temperature Heating Systems in Nordic Single-Family Dwellings

2018 ◽  
Vol 8 (10) ◽  
pp. 1973 ◽  
Author(s):  
Adnan Ploskić ◽  
Qian Wang ◽  
Sasan Sadrizadeh
Keyword(s):  
Low Temperature ◽  
Environmental Impact ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Hot Water ◽  
Single Family ◽  
Efficient Operation ◽  
Heating Systems

The aim of this study was to map the parameters that have the greatest impact on the environmental impact of heating systems usually used in Nordic single-family dwellings. The study focused on mapping the technical requirements for efficient operation of heating systems in a broader context. The results suggest that the ability of a heating system to be operated with a low-temperature water supply depends to a large extent on the heating demand of a building. It was shown that an increase in the water flow rate in hydronic circuits would significantly increase the thermal efficiency from analyzed heating systems. This increase would not increase the pumping power need, nor would it create noise problems in distribution network if the distribution pipes and thermostatic valves were properly selected. However, this increase in water flow rate improved the efficiency of considered closed-loop heat pump. It was further shown that the efficiency of the heat pump could be additionally improved by halving the energy needs for the domestic hot-water and circulators. The main conclusion from this study is that exergy usage, CO2 emission and thereby environmental impact are significantly lower for heating systems that are operated with small temperature drops.

Modeling and Simulation Assessment of Solar Photovoltaic/Thermal Hybrid Liquid System Using TRNSYS

2015 ◽  
Vol 813-814 ◽  
pp. 700-706 ◽  
Author(s):  
R. Geetha ◽  
M.M. Vijayalakshmi ◽  
E. Natarajan
Keyword(s):  
Modeling And Simulation ◽  
Hybrid System ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Water Flow Rate ◽  
Exergy Efficiency ◽  
Hot Water ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Electrical Efficiency

The PV/T hybrid system is a combined system consisting of PV panel behind which heat exchanger with fins are embedded. The PV/T system consists of PV panels with a battery bank, inverter etc., and the thermal system consists of a hot water storage tank, pump and differential thermostats. In the present work, the modeling and simulation of a Solar Photovoltaic/Thermal (PV/T) hybrid system is carried out for 5 kWp using TRNSYS for electrical energy and thermal energy for domestic hot water applications. The prominent parameters used for determining the electrical efficiency, thermal efficiency, overall thermal efficiency, electrical thermal efficiency and exergy efficiency are the solar radiation, voltage, current, ambient temperature, mass flow rate of water, area of the PV module etc. The simulated results of the Solar PV/T hybrid system are analyzed for the optimum water flow rate of 25 kg/hr. The electrical efficiency, thermal efficiency, overall thermal efficiency, equivalent thermal efficiency, exergy efficiency are found to be 10%, 34%, 60%, 35% and 13% respectively. The average tank temperature is found to be 50°C.

scholarly journals A Standard-Based Method to Simulate the Behavior of Thermal Solar Systems with a Stratified Storage Tank

Energies ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 266 ◽  
Author(s):  
Edoardo Alessio Piana ◽  
Benedetta Grassi ◽  
Laurent Socal
Keyword(s):  
Solar System ◽  
Solar Energy ◽  
Storage Tank ◽  
Hot Water ◽  
Design Parameters ◽  
Fluid Temperature ◽  
Forced Circulation ◽  
Solar Systems ◽  
Solar Field ◽  
The Impact

Thermal solar systems are interesting solutions to reduce CO 2 emissions and gradually promote the use of renewable sources. However, sizing such systems and analysing their behavior are still challenging issues, especially for the trade-off between useful solar energy maximization and stagnation risk minimization. The new EPB (Energy Performance of Buildings) standard EN 15316-4-3:2017 offers several methods to evaluate the performance of a forced circulation solar system. One of them is a dynamic hourly method that must be used together with EN 15316-5:2017 for the simulation of the stratified storage tank connected with the solar loop. In this work, such dynamic hourly method is extended to provide more realistic predictions. In particular, modeling of the pump operation due to solar fluid temperature exceeding a set threshold, or due to low temperature differential between solar field and storage tank, is introduced as an on–off control. The implemented code is applied to a case study of solar system for the preparation of domestic hot water and the impact of different design parameters is evaluated. The model predicts a higher risk of overtemperature lock-out or stagnation when the solar field surface is increased, the storage volume is reduced and water consumption is set to zero to simulate summer vacation periods. Finally, a simple modulating control with a time step of a few seconds to a few minutes is introduced, quantitatively showing the resulting benefits in terms of useful solar energy increase, back-up operation savings and reduced auxiliary energy use.

A Software Optimization of the Solar Energy System Performance

2014 ◽  
Vol 899 ◽  
pp. 199-204
Author(s):  
Lukáš Skalík ◽  
Otília Lulkovičová
Keyword(s):  
Solar System ◽  
Solar Energy ◽  
System Performance ◽  
Solar Collector ◽  
Energy Demand ◽  
Fossil Fuels ◽  
Thermal Protection ◽  
Energy Systems ◽  
Energy System ◽  
Hot Water

The energy demand of buildings represents in the balance of heat use and heat consumption of energy complex in the Slovak national economy second largest savings potential. Their complex energy demands is the sum of total investment input to ensure thermal protection and annual operational demands of particular energy systems during their lifetime in building. The application of energy systems based on thermal solar systems reduces energy consumption and operating costs of building for support heating and domestic hot water as well as savings of non-renewable fossil fuels. Correctly designed solar energy system depends on many characteristics, i. e. appropriate solar collector area and tank volume, collector tilt and orientation as well as quality of used components. The evaluation of thermal solar system components by calculation software shows how can be the original thermal solar system improved by means of performance. The system performance can be improved of more than 31 % than in given system by changing four thermal solar system parameters such as heat loss coefficient and aperture area of used solar collector, storage tank volume and its height and diameter ratio.

scholarly journals Performance Enhancement of Split Air Conditioner During Evaporative Cooling Application

2021 ◽  
Vol 86 (2) ◽  
pp. 147-156
Author(s):  
Rahmat Iman Mainil ◽  
Ahmad Wisnu Sulaiman ◽  
Afdhal Kurniawan Mainil ◽  
Azridjal Aziz
Keyword(s):  
Air Temperature ◽  
Flow Rate ◽  
Air Conditioning ◽  
Evaporative Cooling ◽  
Water Flow Rate ◽  
Coefficient Of Performance ◽  
Air Conditioner ◽  
Discharge Water ◽  
Cooling Module ◽  
The Impact

The increase of condenser temperature and pressure in air-conditioning leads to decreased cooling capacity and the increase of power consumption. Evaporative cooling could improve the thermal performance of the system. In this study, the evaporative cooling module was installed before the condenser to reduce the inlet air temperature to the condenser unit. The impact of condenser air temperature on the air conditioning system's overall performance was determined by varying the cooling pad discharge water flowrate of 880, 1040, and 1200 mL/min. The cooling load of 2000 W was employed in this experiment. The obtained results were compared with the air conditioning without an evaporative cooling module. It shows that the coefficient of performance (COP) increases with the increase of discharge water flow rate. The highest COP obtained is 7.09 at the flow rate of 1200 mL/min. The compressor work reduces about 6.57 % as compared with the air conditioner without evaporative cooling application. Besides, the COP increases by 12. 95 % at the highest flow rate.

scholarly journals An experimental investigation on the coefficient of performance of the small hot water heat pump using refrigeration R410A and R32

2020 ◽  
Vol 3 (2) ◽  
pp. First
Author(s):  
Le Minh Nhut ◽  
Tran Quang Danh
Keyword(s):  
Ambient Temperature ◽  
Water Temperature ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Electric Heater ◽  
Initial Water

Hot water is an important factor in domestic life and industrial development. Today, the heat pump is used to produce hot water more and more popular because it has many advantages of saving energy compared to the method of producing hot water by the hot water electric heater. The main aim of this study is to evaluate of the coefficient of performance (COP) of the small hot water heat pump using refrigeration R410A and R32. The capacity of both hot water heat pump is similar, one using new refrigerant R32 and other using refrigerant R410A. These heat pumps were designed and installed at the Ho Chi Minh City University of Technology and Education to evaluate the COP for the purpose of application the new refrigerant R32 for hot water heat pump. The compressor capacity is 1 Hp, the volume of hot water storage tank is of 100 liters and is insulated with thickness of 30 mm to reduce the heat loss to invironment, the required hot water temperature at the outlet of condenser is 50 oC, and the amount of required hot water is 75 liters per batch and is controlled by float valve. The experimental results indicate that the COP of the heat pump using the new refrigerant R32 is higher than heat pump using refrigerant R410A from 9% to 15% when the experimental conditions such as ambient temperature, initial water flow rate through the condenser and the required temperature of hot water were the same. In addition, the effect of the ambient temperature, initial water temperature and water flow rate were also evaluated.

scholarly journals Solar water heating systems for different buildings under a hot climate; parametric optimization and economic analysis

2018 ◽  
Vol 3 ◽  
pp. 3 ◽  
Author(s):  
Kheira Tabet Aoul ◽  
Ahmad Hasan ◽  
Hassan Riaz
Keyword(s):  
Flow Rate ◽  
Tilt Angle ◽  
Water Flow Rate ◽  
Climatic Conditions ◽  
Hot Water ◽  
Solar Thermal ◽  
Design Decision ◽  
Water Heating ◽  
Heating Systems ◽  
Hot Climate

Building applied solar thermal systems are considered by different stakeholders an attractive alternative to traditional space and water heating systems. However, their performance depends largely on climatic conditions, water heating needs and operational parameters which, in turn, offer opportunities for performance optimization. The present research attempts to provide architects with a design decision tool that integrates solar thermal collectors efficiently to meet hot water demand for various building types inclusive of residential, commercial and industrial in a hot climate. The analysis is conducted numerically through a thermal model developed and executed in TRNSYS and validated experimentally. The parameters investigated include the collector tilt angle, azimuth angle and collector inlet fluid flow rate. Finally, the collector aperture area required per building foot print area is determined. The research revealed that for a 1000 m2 footprint building area of schools, offices, residential, factories and hospitals would require respectively 8 m2, 10 m2, 14 m2, 24 m2 and 38 m2 of the static collector installed at 24° tilt angle with optimal water flow rate. Additional operational aspects of collector tracking, and solar radiation concentration were investigated and further reduce the required collector area. A simple payback period analysis reveals a return on investment of 2 years applying subsidized tariff rates under the climatic conditions of, or similar to Dubai, in the United Arab Emirates.

Sign in / Sign up

Export Citation Format

Share Document